Samsung Shr5162 N Manual

							 
01 INTRODUCING
introducing _07
REMOTE CONTROL
RECORD
Starts or ends the 
recording. 
OPEN/CLOSE
Used to open and close 
the DVD-RW tray.
0~9
Selects a single channel 
while in live mode. Used  for inputting numeric  values. 
REC LOCK
Locks the record function.
AUDIO
Toggles Audio On and 
Off.
BACKUP
Press it for backup 
operation.ALARM
Cancels sending alarms.MODE
Select a split screen.
FR (fast rewind) 
FR (fast reverse): Used for quick backward search while in play. (-x2, -x4,  -x8, -x16, -x32, -x64)
STOP 
Ends playing. 
FF (fast forward) 
 
Used for quick forward 
search while in play. (x2, 
x4, x8, x16, x32, x64)
Play/Pause Pauses or resumes 
playing. 
MENU
Goes to the system menu 
screen or moves to the  upper menu. ZOOM
Implements the digital 
zoom (x2).
SEARCH
Goes to the search select 
screen.FREEZE
Performs the FREEZE 
function in live mode. 
UPDOWN
LEFT

RIGHT 
Used for changing 
settings or for moving the  cursor up/down/left/right.
ENTER Shows the cursor for 
channel selection in live 
mode or used as the 
selection button for menu 
configuration. 
PTZ
Toggles PTZ mode On 
and Off. TELE
Performs the TELE 
function in PTZ mode.WIDE
Performs the WIDE 
function in PTZ mode. 
SYS ID
Use for inputting or 
confirming system or 
remote control ID. PRESET
Performs the PRESET 
function in PTZ mode. VIEW
Performs the VIEW 
function in PTZ mode.
Using the NUMERIC Buttons  CHANNEL 1–9 Press the 1 to 9 button respectively.
  CHANNEL 10 Press the 0(10+) button, release, and press the 0 button again with in 3 seconds.Or press the 0(10+) button, 
release, and wait 3 seconds. 
  CHANNEL 11–16 Press the 0(10+) button, release, and press the 1 (or 2, 3, 4, 5, 6) button  again within 3 seconds.Changing the Remote Control IDAs you press the SYS ID button, input the desired 2-digit ID in order (Remote control default ID: 00). 
For instance, to change the remote control ID to 08, press the SYS ID button, and then input 0 and 8 buttons in order.
After the input completes, press the SYS ID button again in order to confirm the setting.
SHR-5162_Eng.indb   72007-06-18   ｿﾀﾀ・11:47:09 
						

							Figure 1
One Year: 24HR X 365 DAY =8,760 HRTemperature
Unit: ºCLife (Unit: HOURS)
Figure 2
08_ installation
installation
You should pay attention to the following before you use the product.
 Do not use it outdoor.
  Do not place water or liquid near the connection part or the prod
 uct.
  Do not impose excessive shock or force.
  Do not pull out the power cord unreasonably.
  Do not disassemble the product on your own.
  Do not exceed the rated input or output voltage range.
  Use the certified power cord only.
  For the product with an input ground, use a power plug with a g
 round pin.
CHECKING INSTALLATION 
ENVIRONMENT
Samsung Digital Video Recorder (hereinafter 
referred to “DVR”) is a high-tech security 
equipment that contains a high-capacity HDD 
and top-notch circuits. High temperature inside 
or outside of the product may reduce the 
product life, deteriorate performance (see the 
graph below; it explains the correlation between 
temperature and product life), and lead to a 
malfunction.
Please keep the following instructions for rack-
mounting the Samsung DVRs to proceed with 
the installation.
1.  The rack on which the DVR is mounted 
should not be sealed off.
2.  And it also can allow air circulation through  the vent.
3.  As shown in the Figure 2, we recommend  you to heap the product with other DVRs or 
use rack-mount devices at a certain space, 
or install a vent system to accommodate 
airflow.
4.  For forming a natural convection, the air  intake hole should be positioned at the 
bottom and the emission at the top.
5.  We recommend you to install each of the air  i
 ntake and emission holes with fan motors for 
sufficient airflow. (The air intake fan should 
be equipped with a filter to prevent possible 
inflow of dust and other impurities.
6. 
As shown in the Figure 1, the temperature 
inside the rack and around the DVR should 
maintain between 0 and 40°C (32 and 104°F).
HDD ADDITION
The user can add up to two hard disks to this 
product. However, there are many factors 
that can cause electric shock, accidents, 
and malfunctioning of the device inside of the 
product.
When the user does not correctly install or 
apply the proper settings, the device may not 
recognize the hard disks or the device will not 
properly run. Therefore, before adding any hard 
disks, it is recommended that you consult the 
specialist from the site where you purchased the 
product.
SHR-5162_Eng.indb   82007-06-18   ｿﾀﾀ・11:47:44    
						

							 
02 INSTALLATION
installation _09
CAUTION
[Checking HDD Data]Please, pay attention to Following 
information to minimize the 
chance of losing HDD data.
 Remember that you should protect 
HDD from any impact or misuse as 
this may cause damaged.
  The Manufacturer is not responsible 
for missing data or defects caused 
by the user’s mishandling.
Note:  
 Adding Extra HDD. Check 
in advance that the HDD 
is compatible with the 
manufacturer’s DVR.
Examples that can cause loss of data 
or damage HDD. 
  Any outside Impact on the case 
which could happen whilst  
disassembling or setting up the 
DVR.
  Power cut or incorrect shutdown 
whilst the DVR is operating.
  Moving or causing any impact on 
the DVR during operation. Please, 
back up events as soon as possible 
to minimize disappointment should 
HDD data be lost.
Things to consider when adding a 
hard disk
 When adding a hard disk, pay attention so 
that the cable doesn’t get caught between 
unsuitable places or the cable’s insulation is 
not damaged. (This may cause a malfunction 
or fire.)
  When adding a hard disk, be careful not to 
have any injury by the pointed edges inside the 
product.
  Pay attention not to lose screws or 
accessories.
If the screws or accessories are not put 
together, the product may malfunction or 
not properly operate.
  If you contact the RTC battery while adding 
hard disks, the battery failure may happen. 
In this case, you will encounter failures when 
setting the time and operating DVR.
  If you don’t connect fan power cables after 
adding hard disks, the fan failure message 
appears on the screen. This can cause 
operation failures because it raises the 
temperature inside your DVR.
  Check the compatibility list of HDDs before 
installing additional HDDs. The list of the 
compatible devices with Samsung DVR can be 
obtained from your vendor.
Setting the jumper
The jumper setting method is illustrated on the 
surface of the purchased HDD. 
Using SAMSUNG hard disk, the jumper setting 
method is as follows:
 HDD jumper for Primary Master and Primary 
Slave.
  
 Jumper setting for Secondary Master (DVD-RW) 
and Secondary Slave.
 
How to add hard disks
Before starting this work, remove the power cord 
from the outlet.
1.  Take out the screws on the left and right 
sides (5 spots for each side) and on the rear 
(1 spot).
2.  Remove the cover from the product. (Slide  t
 he cover slightly backward, lift it upward and 
remove it.)
SHR-5162_Eng.indb   92007-06-18   ｿﾀﾀ・11:47:46      
						

							BRACKET-
HDD(A)
BRACKET-
HDD(B)
BRACKET-HDD(A)
SCREW-SPECIAL
Screwdriver
Screwdriver
10_ installation
3.  There are brackets (Bracket-HDD) mounted 
on the right and left sides where you can 
mount HDDs. Remove the screws holding 
each bracket to mount an HDD onto.
4.  If you want to add a hard disk, remove  Bracket-HDD(A), power supply cable, signal 
transmission cable (IDE Cable), and fan 
cable. 5.  To add a hard disk, the built-in HDD (Primary 
Master) should have been installed. Basically 
a built-in HDD has been installed as the 
Primary Master and a DVD-RW driver as the 
Secondary Master. Before adding a hard 
disk, set the jumper for master and slave. 
The jumper setting method is illustrated 
on the surface of the purchased hard disk. 
Fix the hard disk to the Bracket using the 
(A)SCREW-SPECIAL (BWH, 6-32UNC, L10. 
5). Align the 5 spots on the bottom and 
mounting holes of the Bracket, insert the 
HDD, and then fix it using the screws.
SHR-5162_Eng.indb   102007-06-18   ｿﾀﾀ・11:47:50        
						

							BRACKET-HDD(B)
Secondary HDD 
IDE Connector Primary HDD 
IDE Connector
 
02 INSTALLATION
installation _11
6.  To add another hard disk after adding a hard disk completes, remove the Bracket-HDD(B) 
on the DVD-RW driver.
7.  Fix the hard disk to the Bracket using 4  (B)SCREW-MACHINE (6-32UNC, L4. 2) 
provided when purchasing the HDD. The 
screws should be fastened not to come 
loose. Fix the Bracket-HDD(B) using screws 
after aligning 4 spots on the bottom and 
mounting holes. 8.  When adding hard disks completes, connect 
the power supply cable, signal transmission 
cable (IDE Cable), and fan cable to the hard 
disks.
9.  After checking whether or not the  connections have no problem, close the 
cover.
10.  Fix the cover using screws. (Each of left and  right sides has 5 spots and the back side 
has 1 spot.)
SHR-5162_Eng.indb   112007-06-18   ｿﾀﾀ・11:47:52        
						

							CONNECTING THE NETWORK
Connecting to Internet through Ethernet (10/100BaseT)
12_ connecting
connecting with other devices
The illustrations are described based on SHR-5162.
CONNECTING VIDEO, AUDIO, AND MONITOR
SHR-5162_Eng.indb   122007-06-18   ｿﾀﾀ・11:47:55 
						

							 
03 CONNECTING
connecting _13
Connecting to Internet through ADSL
CONNECTING THE USB
1.  There are two USB connecting ports on the front and rear panels of the product.
2.  USB Hard Disk, USB CD/DVD, and USB  Memory can be connected through any of 
those ports.
3.  If the USB HDD is connected to the system,  it should be detected and set through 
Menu > System > Storage Setup before 
operation.
4.  The product provides the HOT PLUG feature  that allows the connection/removal of USB 
devices during system operation.
CAUTION
 The USB type of hard disk 
should be set to Master.
  If the backup USB device cannot 
be formatted in the DVR, format 
it as FAT32 using your PC.
For more details, refer to the System 
section in Chapter 5 Menu Setup.
CONNECTING THE ALARM 
INPUT/OUTPUT
The Alarm IN/OUT ports on the rear of the 
product have the following elements:
 ALARM IN 1 to 16: Alarm input ports
  ALARM RESET: When receiving an ALARM 
RESET signal, the system clears the current 
ALARM input or output signal and resumes 
alarm sensing. 
  ALARM OUT 1 to 4: Alarm output ports
 
5162 Alarm IN/OUT Ports

 
5082 Alarm IN/OUT Ports
SHR-5162_Eng.indb   132007-06-18   ｿﾀﾀ・11:47:58 
						

							14_ connecting
CONNECTING THE RS-485 
DEVICE
You can connect an RS-485 device through a 
rear port of the product. For example, you can 
connect and control PTZ cameras supporting the 
RS-485 communication. 
You can also adopt either Half Duplex or Full 
Duplex method for exchanging data.
Supportable baud rates are 600, 1200, 2400, 
4800, 9600, 19200, and 38400.
CAUTION
  Check if the RS-485 device is 
compatible with the product first.
  Then pay attention not to change 
the polarity (+/-) of RS-485 when 
connecting it. 
PTZ device 
Half Duplex Type
  Data (–)
  Data (+)
Full Duplex Type
  Rx(+)           
 
  Rx(–)
  Tx(–)
  Tx(+) 
    
  
Rear
Tx(–)           
    
Tx(+)
Rx(–) 

       
    
Rx(+)
SHR-5162_Eng.indb   142007-06-18   ｿﾀﾀ・11:48:00 
						

							CAM_01
CAM_01 V.Loss
 
04 LIVE
live _15
live
OPERATING THE SYSTEM
Turn on the power and the following Samsung 
logo appears. 
Upon completion of initializing procedure, the 
live screen appears with a beep sound. (It takes 
about one minute until a live screen comes up.) 
 If a new HDD is installed, the initialization 
may take much more time because it 
includes a new HDD initialization.
  If the live screen does not appear or 
the LEDs on the front panel repeat 
f

lickering, please check the connections. 
If the system does not operate normally, 
contact the expert from the shop where 
you bought the product.
The live screen does not affect the earlier MENU 
settings. If you reboot the system when a 
recording is in progress, the recording will start 
again.
LIVE SCREEN MODE
Live screen icons
The live screen icons display the status of current 
setup or function.
: Recording icon
Each icon represents Normal/Event 
(Alarm+Motion)/Schedule Recording.
: Recording Video Size icon
Each icon represents the recording size of 
Normal or CIF.
  Normal: Half D1—(NTSC) 720x240, (PAL) 
720x288
  CIF: CIF— (NTSC) 352x240, (PAL) 352x288
 Half D1 is an MPEG-4 video encoding 
mode in which half the horizontal 
resolution is sampled.
: Record Lock icon
It indicates that the record lock is activated. 
This icon appears when you are recording video 
i

mages while the record lock is set. To cancel the 
recording, enter the preset password.
SHR-5162_Eng.indb   152007-06-18   ｿﾀﾀ・11:48:02         
						

							16_ live
: PTZ icon
T
his icon appears when setting the PTZ device 
and it changes to yellow when operating the PTZ.
: Audio icon
This icon represents the ON/OFF status of audio 
and it changes to yellow when the audio is set to 
ON. It does not appear in Video mode or when 
the audio is disabled.
: Sensor Active icon
This icon appears in the channel linked with the 
external sensor signal when the sensor is active.
: Motion Event icon
This icon appears in the Motion Event channel 
when the motion detection is set to ON.
: Zoom icon
This icon appears while the Zoom operation 
is active and disappears by canceling the 
operation.
: Freeze icon
This icon appears in Freeze mode and 
disappears by canceling the freeze operation.
: Recording Hard Disk Full icon
This icon appears when the hard disk space is 
not sufficient when recording.
: Auto Sequence icon
This icon appears in Auto Sequence mode.
: Backup Play icon
This icon appears when the backup data is now 
played.
: Fan Error icon
This icon appears when the fan does not work 
properly.
: No HDD icon
This icon appears when there is a dysfunctional 
hard disk.
When the Fan Error icon or No HDD 
icon appears, please contact the service 
center.
V.Loss/V.Off: Video input status
When there is no video data input while the video 
is active, V.Loss appears in the channel. When 
you set the Video On/Off to OFF, V.Off appears.
Live screen modes
The SHR-5162 model receives 16 live images 
and displays them in the following 9 modes 
as shown in the picture. To see each mode in 
order, repeatedly press the MODE button on the 
front panel or remote control. But the SHR-5082 
model has no 16-split mode. 
CAM_01 CAM_01 CAM_01
CAM_01 CAM_01CAM_01
CAM_01
CAM_05 CAM_06 CAM_07 CAM_08 CAM_02
CAM_02
CAM_03
CAM_04 CAM_01
CAM_03 CAM_02
CAM_04 CAM_05
CAM_06 CAM_07
CAM_02
CAM_03
CAM_02
CAM_03 CAM_04
CAM_02 CAM_03
CAM_04 CAM_05 CAM_06 CAM_04 CAM_05 CAM_06
CAM_07 CAM_08 CAM_09CAM_01 CAM_02 CAM_03 CAM_04
CAM_05 CAM_06 CAM_07 CAM_08
CAM_09 CAM_10 CAM_11 CAM_12
CAM_13 CAM_14 CAM_15 CAM_16
8 Split Mode PIP Mode Single Mode
Auto Sequence Mode
16 Split Mode 9 Split Mode 6 Split Mode
4 Split Mode 7 Split Mode
CAM_01
CAM_01 CAM_01
CAM_01 CAM_01CAM_01
CAM_01
CAM_05 CAM_06 CAM_07 CAM_08 CAM_02
CAM_02
CAM_03
CAM_04 CAM_01
CAM_03 CAM_02
CAM_04 CAM_05
CAM_06 CAM_07
CAM_02
CAM_03
CAM_02
CAM_03 CAM_04
CAM_02 CAM_03
CAM_04 CAM_05 CAM_06 CAM_04 CAM_05 CAM_06
CAM_07 CAM_08 CAM_09CAM_01 CAM_02 CAM_03 CAM_04
CAM_05 CAM_06 CAM_07 CAM_08
CAM_09 CAM_10 CAM_11 CAM_12
CAM_13 CAM_14 CAM_15 CAM_16
SHR-5162_Eng.indb   162007-06-18   ｿﾀﾀ・11:48:03