Sanyo Dsr 3716 P Manual
Have a look at the manual Sanyo Dsr 3716 P Manual online for free. It’s possible to download the document as PDF or print. UserManuals.tech offer 550 Sanyo manuals and user’s guides for free. Share the user manual or guide on Facebook, Twitter or Google+.
English
General settings
How to set 70
1Connect the RS-485 terminal on the rear panel of
the DVR with the system controller (Figure 1).
2Display the screen as explained in
Displaying the general settings screen, and then
turn the S-dial clockwise. (P62)
The DATA SPEED 19200 indicator starts blinking.
3Turn the J-dial to select the desired DATA SPEED
(example: 9600), and then turn the S-dial twice
clockwise.
Selections: 2400/4800/9600/19200
The OFF indicator of STATUS INFO starts blinking.
4Repeat the procedure for selecting the desired
settings for each item.
STATUS INFO
OFF: The status information will not be sent.
ON: The status information will be sent.
ALARM INFO
OFF: The alarm information will not be sent.
ON: The alarm information will be sent.
ADDRESS
The address should be between 000~127.
The address is fixed, and it should match the
address of the PTZ camera. Refer to the List of
camera address for more information. (P90)
Refer to the system controllers instruction manual for
more information about the control method.
5Press the EXIT/OSD button.
FRS-485 settings
MENU
(J)(S)
DATA SPEED : 19200
STATUS INFO : ON
ALARM INFO : ON
ADDRESS : 001
6.RS-485 SET
3.GENERAL SET
STATUS INFO : OFF
EXIT/OSD
POWER MODE AU TO MENU
RS485B A
61
VIDEOCOM SWON1
234ABTELEMETRY
12V
SW
ON1
234RS-485TERMINATEOFF ON
RS-485TERMINATEOFF ON
CARD CARDMENU
RESETEJECTCARD CARDMENU
RESETEJECT
Figure 1 (Do not use telephone wires.)
System controller
(sold separately)
Straight cable Cross cableTo o t h e r
A terminals
The DVR supports straight and cross-type cables.
Straight type:
A straight cable connects connector A to A, and
B to B of the RS-485 connectors.
Cross type:
A cross cable connects connector A with B, and
B with A on the RS-485 connectors.
Pin numberConnector AConnector B
1 Not used Not used
2 Not used Not used
3AB
4BA
5 Not used Not used
6 Not used Not used
Dome camera (sold separately)
Terminator switch settings
If multiple devices are connected, terminator settings are
necessary at both ends. If the terminator settings are not
correct, correct data will not be sent to the devices.
Set the terminator switch on both ends (first device and last
device) to ON, and set it to OFF on all other devices.
English
General settings
71 How to set
The protocol (address) and the external alarm trigger
control settings are needed when operating the coaxial
superimposed dome camera.
If the protocol settings are set to OFF the ALARM REC
TRIGGER SET cannot be set.
1Connect the VIDEO IN terminal on the rear panel of
the DVR to a remotely controllable dome camera
using a coaxial cable. (Figure 1)
2Display the screen as
explained in Displaying the general settings
screen (P62).
3Turn the J-dial to select PROTOCOL/ADDRESS
SET and then turn the S-dial clockwise.
The screen is
displayed.
4Turn the J-dial to move the cursor to the channel
number (example: 06) of the VIDEO IN terminal
where the camera is connected to the rear panel of
the DVR, and then turn the S-dial clockwise.
The OFF starts blinking.
5Turn the J-dial to select the PROTOCOL setting
(example: SANYO COAX1), and then turn the S-dial
clockwise.
The address (ADD.) is preset, it cannot be modified.
Refer to List of camera addresses for more
information. (P90)Selections:
OFF: No camera control
SANYO COAX1:
Camera control by coaxial superimposition of the
SANYO (SSP) protocol.
The address is automatically displayed.
SANYO RS485:
Camera control by SANYO (SSP) protocol using
RS485.
The address is automatically displayed.
BBV COAX:
Camera control by coaxial superimposition of the
BBV protocol.
PELCO COAX:
Camera control by coaxial superimposition of the
PELCO protocol.
SANYO COAX2:
Camera control by high-speed coaxial
superimposition.
6Press the EXIT/OSD button.
7Press the FUNC. button.
The indicator on the FUNC. button and the control
indicators turn on. (P73)
Press the FUNC. button again to exit the function
control.
GCamera control settings
MENU
(J)(S)
7.CAMERA CONTROL SET
3.GENERAL SET
1. PROTOCOL/ADDRESS SET ->
2. ALARM REC TRIGGER SET ->
CH PROTOCOL ADD. CH PROTOCOL ADD.
01 OFF --- 09 OFF ---
02 OFF --- 10 OFF ---
03 OFF --- 11 OFF ---
04 OFF --- 12 OFF ---
05 OFF --- 13 OFF ---
06 OFF --- 14 OFF ---
07 OFF --- 15 OFF ---
08 OFF --- 16 OFF ---
06 OFF ---
Third-party cameras controlled by RS485, RS422
etc. are not supported. Consult with the store where
you purchased your system regarding the types of
cameras that are supported.
In order to prevent control mistakes, set the
PROTOCOL setting to OFF for channels with
cameras that are not capable of coaxial
superimposition or not of the supported types.
06 SANYO COAX1 006
EXIT/OSD
FUNC.
POWER MODE AU TO MENU
Dome camera (sold separately)
Figure 1
English
General settings
How to set 72
Depending on the settings of the selections under
ALARM RECORDING, the camera lens can be set to
move to a preset position or automatic panning when an
alarm is detected.
Confirm the ALARM RECORDING setting. (P56)
1Display the screen
using Displaying the general settings screen
(P62).
2Turn the J-dial to select ALARM REC TRIGGER
SET and then turn the S-dial clockwise.
The screen is
displayed.
3Turn the J-dial to select the camera (CH) that will do
the trigger operation when an alarm is detected and
then turn the S-dial clockwise.
The OFF starts blinking.
4Turn the J-dial to select the motion operation
(example: 05 SEQUENCE) and then turn the S-dial
clockwise.
The SEQUENCE is displayed, the cursor moves to the
OFF of the next camera so other cameras can be set
if necessary.
Selections:
OFF: No trigger operation.
PRESET (2~9/16): Moves to the preset number.
PAN: Starts auto panning.
TOUR: Starts tour operations.
SEQUENCE: Starts automatic sequence operation.
5Press the EXIT/OSD button.
6Press the FUNC. button.
The indicator on the FUNC. button and the control
indicators turn on. (P73)
Press the FUNC. button again to exit the function
control.
G-1Alarm recording trigger settings
ALARM RECORDING : OFF
PICTURE QUALITY : ENHANCED
AUDIO RECORDING : OFF
ALARM INTERLEAVE : ONLY
REC RATE: 12.5FPS, DURATION: 20SEC
PRE-ALARM RECORDING : ***
REC RATE: **** FPS, DURATION: ****
=> (01731 ALARMS CAN BE RECORDED)
ALARM TRIGGER : ALARM
MOTION SENSOR ->
MENU
(J)(S)
7.CAMERA CONTROL SET
3.GENERAL SET
1. PROTOCOL/ADDRESS SET ->
2. ALARM REC TRIGGER SET ->
CH PROTOCOL ADD. CH PROTOCOL ADD.
01 OFF --- 09 OFF ---
02 OFF --- 10 OFF ---
03 OFF --- 11 OFF ---
04 OFF --- 12 OFF ---
05 OFF --- 13 OFF ---
06 OFF --- 14 OFF ---
07 OFF --- 15 OFF ---
08 OFF --- 16 OFF ---
CH ACTION CH ACTION
01 --------- 09 ---------
02 --------- 10 ---------
03 --------- 11 ---------
04 --------- 12 ---------
05 --------- 13 ---------
06 --------- 14 ---------
07 --------- 15 ---------
08 --------- 16 ---------
Note:When several alarms are detected at the same time, it is
possible that the camera control is disabled, depending on the
camera control setting for the alarm recording.
05 SEQUENCE
EXIT/OSD
FUNC.
English General settings 73 How to set bCamera control is not possible in the following cases, even if the function indicator (FUNC.) is ON. While displaying menus, or the search menu During playback (during pause, or copy menu is display) During quad-screen, multi-screen (9/16) and plus screen display During zooming, automatic scrolling and monitor 2 display bIf another button is pressed while the following indicators are blinking (controllable state), the control function will be automatically cancelled. PRESET, IRIS, FOCUS indicators APress the FUNC. button. While the FUNC. indicator is ON, the dome cameras can be operated by using the control buttons listed under 1 ~ H. 1Preset button (PRESET) When the PRESET button is pressed followed by the camera selection button, the lens moves to the preset position, and the preset call is cancelled. Pressing the PRESET button for approximately 3 seconds will activate the registration status. Pressing on the camera selection button allows you to register it. 2Sequence button (SEQUENCE) The cameras will start automatic sequence operation. If another button is pressed, the automatic sequence operation will be cancelled. 3Tour button (TOUR) Performs tour operation. If another button is pressed, the tour operation will be cancelled. 4Automatic panning button (AUTO PAN) Performs automatic panning. If another button is pressed, panning will stop. 5Menu button (MENU) Displays the cameras internal menu on the monitor. 6Confirmation button (ENTER) This button is used to confirm the contents of the menu screen. 7Autofocus button (AF) Use this button to adjust the focus with one touch. 8Iris button (IRIS) Use this button to switch to iris adjustment mode; the IRIS indicator will start blinking. Press the ZOOM/I/FOo button to close the iris, and press the ZOOM/I/FOp button to open the iris. Press the IRIS button once again to exit the iris adjustment mode. 9Focus button (FOCUS) Use this button to switch to focus adjustment mode; the FOCUS indicator will start blinking. Press the ZOOM/I/FOo button to set the focus on nearby objects, and press the ZOOM/I/FOp button to set the focus on far-off objects. Press the FOCUS button once again to exit the focus adjustment mode. FZoom/Iris/Focus button (ZOOM/I/FO) Press the o button to shrink the screen, and press the p button to enlarge it. GPan dial (PAN) Performs panning. Turn the PAN dial clockwise to move the lens to the right, and turn it counterclockwise to move the lens to the left. Larger turning angle results in faster movement; and smaller turning angle results in slower movement. HTilt dial (TILT) Performs tilting. Turn the TILT dial clockwise to tilt the lens down, and turn it counterclockwise to tilt the lens up. G-2Camera control from the DVR PRESETMENU ENTER AF IRIS FOCUS ZOOM/I/FOAU TO PA N SEQUENCE TOURPAN 4 2 13 9F H56 78 G A
English
How to set 74
Screen setting
Menu configuration
CH 01 02 03 04 05 06 07 08
MAIN MON. OFF OFF OFF OFF OFF OFF OFF OFF
MON.2 OFF OFF OFF OFF OFF OFF OFF OFF
NETWORK OFF OFF OFF OFF OFF OFF OFF OFF
CH 09 10 11 12 13 14 15 16
MAIN MON. OFF OFF OFF OFF OFF OFF OFF OFF
MON.2 OFF OFF OFF OFF OFF OFF OFF OFF
NETWORK OFF OFF OFF OFF OFF OFF OFF OFF
CH 01 02 03 04 05 06 07 08
MAIN MON. ON ON ON ON ON ON ON ON
MON.2 ON ON ON ON ON ON ON ON
CH 09 10 11 12 13 14 15 16
MAIN MON. ON ON ON ON ON ON ON ON
MON.2 ON ON ON ON ON ON ON ON
QUAD1 QUAD2
QUAD3 QUAD4
CHECK THE SCREEN ->
01
0205
04 0306
08 07
0910 13
12
1114
16 15
CHECK THE SCREEN ->
01
02
0503
06 04
08 09 07
CHECK THE SCREEN ->
01
02
0603
07 05
10 1104
08
12 09
14 15 16 13
0302
0506
01
04
070809
12
16
03 04
13 14 1507
08
09 10 11 12
0102
05060201
0403
MAIN MON. FULL : 1SEC
QUAD : 1SEC
MON.2 FULL : 1SEC
INDIVIDUAL INTERVAL (SEC)
01: 1 02: 1 03: 1 04: 1
05: 1 06: 1 07: 1 08: 1
09: 1 10: 1 11: 1 12: 1
13: 1 14: 1 15: 1 16: 1
06
03
04
01-01-06 00:00:00
05
0605
0807
0201
0403
01
04
CH01 COLOR LEVEL : 5
1.MULTI SCREEN : NORMAL
QUAD POSITION SET ->
MULTI 9 POSITION SET ->
MULTI 16 POSITION SET ->
2.SEQUENCE : 1SEC
SEQUENCE SET ->
MAIN/MON.2 MONITOR SET ->
3.MASK : OFF
MASK SET ->
4.COLOR LEVEL SET ->
TIME PERIOD : T-1 (06:00-11:30)
TIME PERIOD : T-1 (06:00-11:30)
bDisplaying the screen settings
1Press the MENU button and use the
J-dial to select 4. SCREEN SET, and
then turn the S-dial clockwise.
The screen appears.
2Turn the J-dial, select the desired
submenu, and turn the S-dial
clockwise.
The selected screen (A~D) is
displayed. Refer to the appropriate
pages for the settings.
(S)
(J)
MENU
1.INITIAL SET ->
2.RECORD SET ->
3.GENERAL SET ->
4.SCREEN SET ->
5.POWER LOSS/USED TIME ->
(S)
(J)
AChanging the multi-screen sequence (P75)
Screen-position modification for live video and playback.
BSwitching screen at time intervals (P76)
This setting is used to scroll all live videos based on preset time intervals.
This setting specifies the monitor to use for live video display during the
time set in the time period settings (TIME PERIOD A/B).
CMasking specific camera images (P78)
This setting specifies when to use a gray pattern to mask certain camera
video on the screen.
DAdjusting color tones of the live video (P79)
This setting is used to adjust the color tone of the video on the monitor.
☞The DSR-3709PA does not display
MULTI 16 POSITION SET.
(DSR-3716PA)
English
Screen setting
75 How to set
1Display the screen as explained in
Displaying the screen settings, and then turn the
S-dial clockwise. (P74)
The NORMAL field of 1. MULTI SCREEN starts
blinking.
2Turn the J-dial, select CHANGE, and then turn the
S-dial clockwise.
Selections:
NORMAL:
No specified display positions for multi-screen
display
CHANGE:
Specified positions for multi-screen (quad/9/16)
display
The cursor moves to QUAD POSITION SET.
Turn the J-dial and select the quad, multi-9 or multi-16
screen as shown below, for changing the display
positions.
3Example: Switching the live video of the camera 5
and camera 1 on the quad screen.
1Turn the J-dial, select QUAD POSITION SET,
and then turn the S-dial clockwise.
The screen
appears.
2Turn the J-dial, select 01 to QUAD1, and then
turn the S-dial clockwise.
The 01 indicator starts blinking.
3Turn the J-dial, select 05, and turn the S-dial
clockwise.
4Turn the J-dial, select CHECK THE SCREEN,
and then turn the S-dial clockwise.
The screen with live
video appears. Check if camera 1 was replaced by
camera 5.
Press the QUAD button to check the screen of
QUAD2 and beyond.
5Turn the S-dial counterclockwise.
The screen
returns.
Repeat the operation for changing the order of multi-9
or multi-16 screen display.
4Press the EXIT/OSD button.
Press the QUAD or the MULTI buttons on the
normal live display to see the order of the display
changed.
AChanging the multi-screen sequence
(S)
4.SCREEN SET
1.MULTI SCREEN : NORMAL
QUAD POSITION SET ->
MULTI 9 POSITION SET ->
MULTI 16 POSITION SET ->
2.SEQUENCE : 1SEC
SEQUENCE SET ->
MAIN/MON.2 MONITOR SET ->
3.MASK : OFF
MASK SET ->
4.COLOR LEVEL SET ->
MENU
1.MULTI SCREEN : CHANGE
QUAD POSITION SET ->
MULTI 9 POSITION SET ->
MULTI 16 POSITION SET ->
2.SEQUENCE : 1SEC
SEQUENCE SET ->
MAIN/MON.2 MONITOR SET ->
3.MASK : OFF
MASK SET ->
4.COLOR LEVEL SET ->
CHECK THE SCREEN ->
01
02
0503
06 04
08 09 07
CHECK THE SCREEN ->
01
02
0603
07 05
10 1104
08
12 09
14 15 16 13
QUAD1 QUAD2
QUAD3 QUAD4
CHECK THE SCREEN ->
01
0205
04 0306
08 07
0910 13
12 1114
16 15
02
04 030102
04 0305
QUAD1QUAD1
05 06
08 07
0910 13
12
1114
16 15
QUAD1 QUAD2
QUAD3 QUAD4
CHECK THE SCREEN ->
02
0403
05
05
02
04 03
QUAD
EXIT/OSD
English
Screen setting
How to set 76
1Display the screen as explained in
Displaying the screen settings (P74).
The cursor moves to the 1. MULTI SCREEN position.
2Turn the J-dial to select 2. SEQUENCE, and then
turn the S-dial clockwise.
Selections: 1/2/ ... 29/30SEC/INDIV.
The 1SEC indicator starts blinking.
After specifying the number of seconds, the cursor will
not move to the SEQUENCE SET position. This way
the automatic sequence will be set to the same interval.
3Turn the J-dial to select the 2. SEQUENCE
(example: 5 seconds), and then turn the S-dial
clockwise.
4Press the EXIT/OSD button.
5Press the SEQUENCE button.
The video on the main monitor and the monitor 2 will
switch every 5 seconds.Display the screen.
1Turn the J-dial to select 2. SEQUENCE, and then
turn the S-dial clockwise.
Selections: 1/2/ ... 29/30SEC/INDIV.
The 1SEC indicator starts blinking.
2Turn the J-dial to select INDIV., and then turn the
S-dial twice clockwise.
The screen appears.
3Turn the S-dial clockwise.
The 1SEC of MAIN MON. FULL starts blinking.
4Setting the interval time between the MAIN MON.
and the MON2.
1Turn the J-dial to select 5SEC for MAIN MON.
FULL, and then turn the S-dial twice clockwise.
Selections: 1/2/ ... 29/30SEC/INDIV.
2Turn the J-dial to select 10SEC for MAIN MON.
QUAD, and then turn the S-dial twice clockwise.
Selections: 1/2/ ... 29/30SEC
3Turn the J-dial to select 15SEC for MON.2
FULL, and then turn the S-dial clockwise.
Selections: 1/2/ ... 29/30SEC/INDIV.
5Press the EXIT/OSD button.
6Press the SEQUENCE button.
The monitor video will be switched the following way:
Main monitor full-screen video every 5 seconds
Main monitor quad-screen video every 10 seconds
Monitor 2 full-screen video every 15 seconds
B
Automatic scrolling of live video of the
main monitor and the monitor 2 at
identical intervals (example: 5 seconds)
(S)
MENU
1.MULTI SCREEN : CHANGE
QUAD POSITION SET ->
MULTI 9 POSITION SET ->
MULTI 16 POSITION SET ->
2.SEQUENCE : 5SEC
SEQUENCE SET ->
MAIN/MON.2 MONITOR SET ->
3.MASK : OFF
MASK SET ->
4.COLOR LEVEL SET ->
4.SCREEN SET
2.SEQUENCE : 1SEC
2.SEQUENCE : 5SEC
EXIT/OSD
SEQUENCE
B-1
Automatic scrolling of live video of the
main monitor and the monitor 2 at
individual intervals (example: 5 seconds)
2.SEQUENCE : 1SEC
MAIN MON. FULL : 1SEC
QUAD : 1SEC
MON.2 FULL : 1SEC
(S)
MAIN MON. FULL : 5SEC
QUAD : 10SEC
MON.2 FULL : 15SEC
EXIT/OSD
SEQUENCE
English
Screen setting
77 How to set
1Display the screen as explained in
Displaying the screen settings (P74).
2Turn the J-dial, select 2. SEQUENCE, and then
turn the S-dial clockwise.
3Turn the J-dial to select INDIV., and then turn the
S-dial twice clockwise.
4Turn the S-dial clockwise.
5Turn the J-dial, select INDIV. for the MAIN MON.
FULL, and then turn the S-dial clockwise.
MAIN MON. QUAD cannot be set to INDIV..
6Turn the J-dial to select MON.2 FULL, and then
turn the S-dial clockwise.
The 1SEC (example) indicator starts blinking.
7Turn the J-dial to select 3SEC, and then turn the
S-dial twice clockwise.
1 SEC of channel 1 (01) under INDIVIDUAL
INTERVAL (SEC) starts blinking.
8Turn the J-dial to set the interval for channel 1 (01)
of the main monitor (example: 5), and then turn the
S-dial clockwise.
Repeat the procedure for setting the interval for the
other channels.
9Press the EXIT/OSD button.
ÀPress the SEQUENCE button.
1Set TIME PERIOD A and TIME PERIOD B using
(P37).
Select TIME PERIOD A or TIME PERIOD B for
SEQUENCE under SELECT TIME PERIOD.
The example uses TIME PERIOD A.
2Turn the J-dial on the screen to
select MAIN/MON.2 MONITOR SET, and then turn
the S-dial twice clockwise.
The screen appears,
and T-1 at TIME PERIOD starts blinking.
3Turn the J-dial to select the desired TIME PERIOD
(example: T-2), and then turn the S-dial twice
clockwise.
The ON indicator at CH 01 on the MAIN MON. line
starts blinking.
4Turn the J-dial, select OFF, and turn the S-dial.
Repeat the procedure to turn OFF the display of all
desired cameras.
5Press the EXIT/OSD button.
6Press the SEQUENCE button.
B-2
Automatic sequence of live video of the
main monitor (full-screen) at individual
intervals, and of the monitor 2 at identical
intervals (example: 3 seconds)
MAIN MON. FULL : INDIV.
QUAD : 1SEC
MON.2 FULL : 5SEC
INDIVIDUAL INTERVAL (SEC)
01: 5 02: 1 03: 1 04: 1
05: 1 06: 1 07: 1 08: 1
09: 1 10: 1 11: 1 12: 1
13: 1 14: 1 15: 1 16: 1
EXIT/OSD
SEQUENCE
B-3Turning off display of specified
cameras during timer-controlled
periods
QUAD POSITION SET ->
MULTI 9 POSITION SET ->
MULTI 16 POSITION SET ->
2.SEQUENCE : 1SEC
SEQUENCE SET ->
3.MASK : OFF
MASK SET ->
4.COLOR LEVEL SET ->
TIME PERIOD T-1 T-2 T-3 T-4
TIME PERIOD A 06:00 11:30 13:30 18:00
TIME PERIOD B 06:00 08:00 14:30 20:00
SELECT TIME PERIOD
SEQUENCE TIME PERIOD A
MASK TIME PERIOD A
MOTION SENSOR TIME PERIOD A
1.MULTI SCREEN : CHANGE
MAIN/MON.2 MONITOR SET ->
TIME PERIOD : T-1 (06:00-11:30)
CH 01 02 03 04 05 06 07 08
MAIN MON. ON ON ON ON ON ON ON ON
MON.2 ON ON ON ON ON ON ON ON
TIME PERIOD : T-2 (06:00-11:30)
CH 01 02 03 04 05 06 07 08
MAIN MON. OFF ON OFF ON OFF ON ON ON
MON.2 ON OFF ON OFF ON OFF ON ON TIME PERIOD : T-2 (06:00-11:30)
EXIT/OSD
SEQUENCE
English
Screen setting
How to set 78
1Set TIME PERIOD A and TIME PERIOD B using
(P37).
Select TIME PERIOD A or TIME PERIOD B for
MASK under SELECT TIME PERIOD.
The example uses TIME PERIOD A.
2Display the screen as explained in
Displaying the screen settings (P74).
The cursor moves to 1. MULTI SCREEN.
3Turn the J-dial, select 3. MASK, and then turn the
S-dial clockwise.
The OFF starts blinking.
4Turn the J-dial, select ON, and turn the S-dial
clockwise.
The cursor moves to MASK SET.
5Turn the S-dial clockwise.
The screen appears and the cursor
moves to T-1.
6Turn the S-dial, and use the J-dial to select the
desired TIME PERIOD (example: T-2), and then turn
the S-dial clockwise.
The cursor moves to 01 (CH) of the MAIN MON. line.
7Turn the J-dial to select the camera number
(example: 03) of the MAIN MON., and then turn the
S-dial clockwise.
8Turn the J-dial, select ON, and turn the S-dial
clockwise.
Repeat the procedure to turn the masking ON for all
desired cameras on MON.2 and on NETWORK.
9Press the EXIT/OSD button.
CMasking specific camera images
TIME PERIOD T-1 T-2 T-3 T-4
TIME PERIOD A 06:00 11:30 13:30 18:00
TIME PERIOD B 06:00 08:00 14:30 20:00
SELECT TIME PERIOD
SEQUENCE TIME PERIOD A
MASK TIME PERIOD A
MOTION SENSOR TIME PERIOD A
1.MULTI SCREEN : CHANGE
QUAD POSITION SET ->
MULTI 9 POSITION SET ->
MULTI 16 POSITION SET ->
2.SEQUENCE : 1SEC
SEQUENCE SET ->
MAIN/MON.2 MONITOR SET ->
MASK SET ->
4.COLOR LEVEL SET ->
(S)
MENU
4.SCREEN SET
3.MASK : ON
MASK SET ->
CH 01 02 03 04 05 06 07 08
MAIN MON. OFF OFF OFF OFF OFF OFF OFF OFF
MON.2 OFF OFF OFF OFF OFF OFF OFF OFF
NETWORK OFF OFF OFF OFF OFF OFF OFF OFF
CH 09 10 11 12 13 14 15 16
MAIN MON. OFF OFF OFF OFF OFF OFF OFF OFF
MON.2 OFF OFF OFF OFF OFF OFF OFF OFF
NETWORK OFF OFF OFF OFF OFF OFF OFF OFF
TIME PERIOD : T-1 (06:00-11:30)
CH 01 02 03 04 05 06 07 08
MAIN MON. OFF OFF ON OFF ON OFF ON OFF
MON.2 OFF ON OFF ON OFF ON OFF ON
NETWORK ON OFF ON OFF ON OFF ON OFF
CH 09 10 11 12 13 14 15 16
MAIN MON. OFF OFF OFF OFF OFF OFF OFF OFF
MON.2 OFF OFF OFF OFF OFF OFF OFF OFF
NETWORK OFF OFF OFF OFF OFF OFF OFF OFF
TIME PERIOD : T-2 (06:00-11:30)
EXIT/OSD
English
Screen setting
79 How to set
1Display the screen as explained in
Displaying the screen settings (P74).
The cursor moves to the 1. MULTI SCREEN position.
2Turn the J-dial, select 4. COLOR LEVEL SET, and
then turn the S-dial clockwise.
The screen of CH01 appears,
and the cursor moves to COLOR LEVEL.
3Press the camera selection button (example: 7) of
the channel where you want to adjust the color
level, and then turn the S-dial clockwise.
The channel switches to CH07, and the 5 field at
COLOR LEVEL starts blinking.
4Turn the J-dial, select the desired COLOR LEVEL,
and then turn the S-dial clockwise.
Selections: 1/2.../8/9/10 (darker)
The color tone of the camera video changes.
5Press the EXIT/OSD button.
DAdjusting color tones of the live video
(S)
MENU
1.MULTI SCREEN : NORMAL
QUAD POSITION SET ->
MULTI 9 POSITION SET ->
MULTI 16 POSITION SET ->
SEQUENCE SET ->
MAIN/MON.2 MONITOR SET ->
3.MASK : OFF
MASK SET ->
4.COLOR LEVEL SET ->
4.SCREEN SET
2.SEQUENCE : 1SEC
CH01 COLOR LEVEL : 5
CH07 COLOR LEVEL : 5
(S)
EXIT/OSD