Sanyo LNS W01 Installation Manual

LCD PROJECTOR
LENS REPLACEMENT
AND
INSTALLATION PROCEDURES
English
Français
Español
Deutsch
Italiano
1AA6P1P2923-- (MV6A) 

- 1 -
E LCD PROJECTOR
LENS REPLACEMENT AND INSTALLATION PROCEDURES
CAUTION
When installing or replacing the Projection Lens, refer to this manual. For
installation of the lens, use the parts designated in the manual. Do not use the
installation manual and Light-Block Sheets in the lens package.
Check the following parts supplied to this projector.
NOTES ON LENS INSTALLATION
●Lens installation and replacement should be made by the qualified service
personnel.
●Be sure to install the lens following this...

UPPER LENS COVER 
- 2 -
E
NOTE : The installation procedure and needed parts
for lens installtaion depend on the type of the
Projection Lens. Check the Model No. of the
Projection Lens and be sure to install or replace the
lens following procedure below.
1  
Remove Lower Lens Cover. Remove 2 Screws A.
Push part B and pull Lower Lens Cover down.
(See Fig. 1.)
2  
Remove 4 Screws C. Pull Upper Lens Cover
toward front and remove. (See Fig. 2.)
3  
Remove 2 Screws D and Cover Plate on the back
of Upper Lens...

- 3 -
E
5  
Connect Lens Motor Lead to the connector
K96T on the circuit board under the lens. (The
model with Lens Motor only.) Fix Lens Motor
Lead with the wire holder on the circuit board.
For installing the lenses listed below, attaching Lens Mounting Adapters is required. Before
mounting the lens, attach Lens Mounting Adapters. Refer to LENS MOUNTING ADAPTER
INSTALLATION.
Model No.: LNS-W02, LNS-S01, LNS-M01
For installing the lenses listed below, removing Guide Pins is required. Before mounting the...

- 4 -
E
6  
This projector has 3 Light-Block Sheets. Use Light-Block Sheet corresponding with lens. (Refer to
the list below.)  
Set Light-Block Sheet through the lens. 
Make sure the shape of Light-Block Sheets and be sure to set them as shown in the Fig. 6.
NOTE:
●Be sure to set each Light-Block Sheets as shown in Fig-6.
●  Make sure the mark (TOP and BACK) on Light-Block Sheets and set them properly.
Light-Block Sheets For each lens.
Lens Model No. 
LNS-S02, LNS-S02Z, LNS-S03
LNS-M01, LNS-T02,...

- 5 -
E
7  
Adjust focus of the Projection Lens. (LNS-W01, LNS-W01Z, LNS-T01, LNS-T01Z and LNS-W03
only.) Set up the projector and project image on the screen. Loosen Focus Lens Lock Screw and
rotate Projection Lens to obtain proper focus. After adjusting focus, be sure to lock Projection Lens
with Focus Lens Lock Screw securely. (See Fig. 4.) Adjust focus of Projection Lens MODEL LNS-
W03, following Focus Adjustment on page 6.
8  
Replace Upper Lens Cover. Slide Light-Block Sheets into the guide of...

- 6 -
E
Focus Lock Screw
Focus Lock Ring
●mark (yellow)
FOCUS ADJUSTMENT (For Model LNS-W03)
Set up the projector and project image on the screen.
1.Loosen the Focus Lock Screw on the projection
lens.
2.Rotate the projection lens to obtain proper focus
on center area of the screen. 
When the distance of the screen and lens is 1 meter,
set ●mark (yellow) of the lens on Focus Lock Screw
position. 
3. Lock the Focus Lock Screw securely.
When proper focus is not observed at outer area of
the screen, proceed...

- 7 -
E
For installing the lenses listed below, attaching Lens Mounting Adapters is required.  
Model No.: LNS-W02, LNS-S01, LNS-M01
1  
Set Lens Mounting Adapters on the lens with 4
Screws. Use the round head screws. 
(See Fig. 8.)
LENS MOUNTING ADAPTER INSTALLATION
Check the following parts supplied with the adapters.
ADAPTER SCREWS     8pcs.  
(4 pcs. for mounting Adapters on the lens and 4 pcs. for mounting Lens on the projector.)
NOTE: Do not use the screws in the lens package.
2  
Mount Projection...

- 8 -
E
NOTE:  Following tabe shows approximate measurement. Actual measurement depends on lens and projectors.SPECIFICATIONS (Throw distance and screen size, screen of lens shift. )
Model No.LNS-S02 
LNS-S02Z
Zoom40
6080
100120150
180200
250300
350400500
600
LNS-W02 
LNS-W02Z
LNS-T02 
LNS-M01 
LNS-M01Z
LNS-S01
LNS-W01 
LNS-W01Z
LNS-T01 
LNS-T01Z
MINMAX
MINMAXMINMAX
MINMAXMINMAXNONENONE1.9
1.5
1.41.15.13.8
3.62.92.31.53.0
2.4
2.11.77.55.5
5.44.33.52.2
4.13.22.92.310.07.37.25.74.62.9...

LNS-S03Lentille IIIde zoom standardMoteur entraîné Moteur entraîné
- 1 -
F PROJECTEUR A LCD
PROCEDURES D’INSTALLATION ET DE REMPLACEMENT DE
LA LENTILLE
ATTENTION
●  FEUILLES DE BLOCAGE LEGER   3 unités
●  ADAPTATEURS DE MONTAGE DE LENTILLE   2 unités
●  VIS D’ADAPTATEURS   8 unités
Ce projecteur accepte les lentilles de projection mentionnées dans la liste ci-dessous.
Utilisez la lentille convenant à l’endroit où vous utilisez le projecteur.
✳ Pour installer ces lentilles, il faut fixer les adaptateurs...