Sharp AR M620N User Manual

LOADING PAPER
2-3
2
3Gently push tray 1-tray 2 into the machine.
Push the tray firmly all
the way into the
machine.
4Set the paper type.
If the paper size was changed from an AB size to an
inch size, or from an inch size to an AB size, or if the
paper type was changed, be sure to change the
appropriate settings as explained in Setting the
paper type and paper size (See page 2-10).
5Loading paper in paper tray 1/tray 2 is now
complete.
Loading paper in paper tray 3
Approximately 500 sheets of standard...

LOADING PAPER
2-4




 
Loading tabbed paper
When using tabbed paper, follow the steps below to attach the special guide to the divider plate at the bottom
edge of the tabbed paper. (Tabbed paper cannot be used in tray 4.)
1Take out the tabbed paper guide.
The guide is stored
inside the left side of the
machine as shown.
Be sure to replace the
guide when you have
finished using it.
2Pull out the tray and attach the guide.
Slide the divider plate to
the position of the
bottom edge of the
tabbed paper and...

LOADING PAPER
2-5
2
Loading paper in paper tray 5 (optional large capacity tray)
The large capacity tray can hold up to 3,500 sheets of A4 size (8-1/2 x 11) SHARP standard paper (80 g/m2 (20
lbs.)). If you wish to change the paper size, please consult your dealer (the paper size must be changed by a service
technician).
1Pull the tray out until it stops.
When the tray is in
operation, do not use
excessive force to pull
the tray out. This may
damage the  tray.
2Place the paper in the centre of the paper...

LOADING PAPER
2-6
Loading paper in the bypass tray
The bypass tray can be used to print on plain paper, postcards, label sheets, tabbed paper, and other special papers.
When using SHARP standard paper, up to 100 sheets can be loaded (up to 20 postcards) for continuous printing
similar to the other trays. For the paper types that can be used in the bypass tray, see Specifications of paper trays
(Types and sizes of paper that can be used in the trays) on page 2-8.
1Open the bypass tray.
When loading A3,...

LOADING PAPER
2-7
2




 
Important points when using the
bypass tray
Be sure to load A5 paper, 5-1/2 x 8-1/2 paper
and postcards as shown (1) horizontal loading in
the diagram below.
(1):Horizontal loading
(2):Vertical loading
When loading plain paper other than SHARP
standard paper, special media other than
postcards, SHARP-recommended transparency
film, or paper to be printed on the back, the
paper must be loaded one sheet at a time.
Loading more than one sheet at a time will cause
misfeeds.
Before...

LOADING PAPER
2-8
Specifications of paper trays (Types and sizes of paper that
can be used in the trays)
The specifications for the types and sizes of paper that can be loaded in the paper trays are shown below.
Tray No. 
(tray name)Applicable paper typesApplicable paper sizesPaper weight
Tray 1
Plain paper (Refer to the next page
More information on plain paper.)A4, 8-1/2 x 11
60 to 105g/m2
(16 to 28 lbs.)
Tray 2 A4, B5, 8-1/2 x 11
Tray 3Plain paper
(Refer to the next page More
information on plain...

LOADING PAPER
2-9
2

 More information on plain paper
Incorrect feeding may result in poor toner fusing (the toner does not adhere to the paper well and can be rubbed
off), skewed feeding, misfeeds, or other failures.

 More information on special media that can be used
Incorrect feeding may result in poor toner fusing (the toner does not adhere to the paper well and can be rubbed
off), skewed feeding, misfeeds, or other failures.

 Paper that can be used for automatic two-sided printing...

LOADING PAPER
2-10
Setting the paper type and paper size
Follow these steps to change the paper type setting when the paper type has been changed in a paper tray.  For the
paper types that can be used in each tray, see page 2-8.
1Press the [CUSTOM SETTINGS] key.
The custom setting
menu screen will
appear.
2Touch the [PAPER TRAY SETTINGS] key.
The paper tray selection
screen will appear.
3Display the setting screen of the desired
paper tray.
Touch the   key or   key to display the
setting screen of the...

LOADING PAPER
2-11
2
8Select output functions that can be used
with the selected tray.
Touch the checkboxes
under the desired items
to select them.

 User type
Select a User type when the name of the paper
type does not appear in the selections or when you
wish to select the tray attributes yourself.
Touch the   key in step 5 on the previous page
to display the user type selection screen and then
select a user type.
9Set the attributes of the paper tray only if
you have selected a user type.
Touch...

LOADING PAPER
2-12
Setting the paper size when a special size is loaded
1Perform steps 1 through 5 of Setting the
paper type and paper size (see page 2-10).
2Touch the [SIZE INPUT] key and then
touch the [AB] tab.
The size entry palette
appears.
3Touch the   key or the   key to enter
the X (width) and Y (length) dimensions of
the paper.
X (width) is initially
selected. To enter Y
(length), touch the  [Y]
key and then enter the
length.
4Touch the [OK] key.
You will return to the size
setting screen of...