Sharp Xg C58x Projector User Manual

Connections and Setup
-27
90°
90°
Example of Standard Setup
Setting up the Screen
Position the projector perpendicular to the screen with all feet flat and level to achieve an optimal image.
Note
•The projector lens should be centered in the middle of the screen. If the horizontal line passing through the
lens center is not perpendicular to the screen, the image will be distorted, making viewing difficult.
•For optimal image, position the screen so that it is not in direct sunlight or room light. Light...

-28
H
Screen
L:Projection distanceLens center Base line:
Horizontal line passing through
the lens center
STRETCH Mode (16:9)
Picture (Screen) size Projection distance [L]Distance from the lens centerDiag. [χ]Width Height Maximum [L1] Minimum [L2] to the bottom of the image [H]
300 (762 cm) 261 (663 cm)147 (373 cm)50 6 (15.4 m) 39 3 (12.0 m) –415 / 16(–12.6 cm)
250 (635 cm) 218 (554 cm)123 (312 cm)42 (12.8 m) 32 8 (10.0 m) –41 / 8(–10.5 cm)
225 (572 cm) 196 (498 cm)110 (279 cm)3710 (11.5 m) 29 5 (9.0 m)...

Connections and Setup
-29
Picture (Screen) size Projection distance [L]Distance from the lens centerDiag. [χ
]Width Height Maximum [L1] Minimum [L2] to the bottom of the image [H]
300 (762 cm) 261(663 cm)147 (373 cm)
250 (635 cm) 218(554 cm)123 (312 cm)
225 (572 cm)196(498 cm)110 (279 cm)
200 (508 cm) 174(442 cm)98 (249 cm)
150 (381 cm) 131(333 cm)74 (188 cm)
133 (338 cm)116(295 cm)65 (165 cm)
106 (269 cm)92 52 (132 cm)
100 (254 cm) 8749 (124 cm)
92 (234 cm) 8045 (114 cm)
123 10
103 3
93
82 8
62 1
55 1...

-30
AN-C27MZ (Optional accessory)
Throw ratio
1:2.7 to 4.3
Picture (Screen) size Projection distance [L]Distance from the lens center 
to the bottom of the image [H]Diag. [χ
]Width
Height
Maximum [L1] Minimum [L2]
300 (762 cm) 261 (663 cm)147 (373 cm)
250 (635 cm) 218 (554 cm)123 (312 cm)
225 (572 cm)196 (498 cm)110 (279 cm)
200 (508 cm) 174 (442 cm) 98 (249 cm)
150 (381 cm) 131 (333 cm) 74 (188 cm)
133 (338 cm)116 (295 cm) 65 (165 cm)
106 (269 cm)92 (234 cm) 52 (132 cm)
100 (254 cm) 87 (221 cm)49 (124...

Connections and Setup
-31
Note
•There is an error of ± 3% in the formula above.
•Values with a minus (–) sign indicate the distance of the lens center below the bottom of the image. STRETCH Mode (16:9)
Picture (Screen) size Projection distance [L]Distance from the lens centerDiag. [χ]Width Height Maximum [L1] Minimum [L2] to the bottom of the image [H]
300 (762 cm) 261 (663 cm)147 (373 cm)33 2 (10.1 m) 26 5 (8.0 m) –5(–12.7 cm)
250 (635 cm) 218 (554 cm)123 (312 cm)27 7 (8.4 m) 22 (6.7 m) –43 / 16(–10.6...

-32
When using the default setting.
▼On-screen Display
Projecting a Reversed/Inverted Image
Projection from behind the screen
■Place a translucent screen between the projector and the au-
dience.
■Reverse the image by setting “Rear” in “PRJ Mode”. See
page 71 for use of this function.
Projection using a mirror
■Place a mirror (normal flat type) in front of the lens.
Info
•When using a mirror, be sure to carefully position both the pro-
jector and the mirror so the light does not shine into the eyes of...

Basic Operation
Basic Operation 

Image Projection
▼Keycode input box
-34
Lamp
indicatorPower
indicator
INPUT
button
',", \, |
buttons
MENU
button ENTER
button
ON button
', ", \, |
buttons MENU button ENTER
button
Basic Procedure
Connect the required external equipment to the pro-
jector before operating the following procedures.
Info
•The language preset at the factory is English.
If you want to change the on-screen display
to another language, reset the language ac-
cording to the procedure on page 
36.
1Plug the power...

Basic Operation
-35
3Press , ,  or  on
the remote control to select the
INPUT mode.
•After pressing  once on the projector,
use 
 to select the desired input mode.
Note
•When no signal is received, “NO
SIGNAL.” will be displayed. When a
signal that the projector is not pre-
set to receive is received, “NOT
REG.” will be displayed.
•When “Auto Search” is “ON”, the
INPUT modes with signals can be
selected. (see page 64.)
•The INPUT mode is not displayed
when “OSD display” is set to “Level
A” or “Level B”....

Image Projection
5Press  to temporarily turn
off the sound.
Note
•Pressing  again will turn the
sound back on.
Selecting the On-screen
Display Language
The on-screen display language of the projec-
tor can be set to English, German, Spanish,
Dutch, French, Italian, Swedish, Portuguese,
Chinese, Korean or Japanese.
1Press .
•The menu will be displayed.
2Press \ or | to select “Lan-
guage”.
3Press ' or " to select the de-
sired language, and then press
.
4Press .
•The desired language will be set...