Sharp Xg C58x Projector User Manual

Easy to Use Functions
-77
Initializing the Settings
This function allows you to initialize the settings you have made in the projector.
Returning to the
Default Settings
Select “All Reset” in the “Options (2)”
menu on the menu screen.
➝ For operating the menu screen, see
pages 42 to 45.
Note
•If a password has been set, the pass-
word input box will be displayed when
selecting “All Reset”.
The following items cannot be initialized.
•C. M. S.
•“Lightness”, “Chroma” and “Hue”
respectively saved for Custom...

-78
This function can be used to display all the adjusted settings as a list on the screen.
Displaying the Adjustment Settings
Overview of All Menu
Settings
Select the “Status” menu on the menu
screen and press 
 .
➝ For operating the menu screen, see
pages 42 to 45.
-78 

Appendix
Appendix 

-80
Cleaning the lens
■Use a commercially available blower or lens
cleaning paper (for glasses and camera lenses)
for cleaning the lens. Do not use any liquid type
cleaning agents, as they may wear off the coat-
ing film on the surface of the lens.
■As the surface of the lens can easily get dam-
aged, be sure not to scrape or hit the lens.
Cleaning the exhaust and intake vents
■Use a vacuum cleaner to clean dust from the
exhaust vent and the intake vent.
Maintenance
Cleaning the projector
■Ensure that...

Appendix
-81
Replacing the Air Filter
Air filter
M4M4
M4 M4
STANDBY button
STANDBY
button
Air filter (not removable)
•
This projector is equipped with air fil-
ters to ensure the optimal operating
condition of the projector.
• The air filters should be cleaned ev-
ery 100 hours of use. Clean the filters
more often when the projector is used
in a dusty or smoky location.
• Ask your nearest Sharp Authorized
Projector Dealer or Service Center to
ex change the filter (PFILDA017WJZZ)
when it is no longer...

5Clean the air filter.
•Clean the dust off the air filter and
cover with a vacuum cleaner extension
hose.
6Replace the air filter.
•Place the air filter underneath the tabs
on the filter cover.
7Replace the filter cover.
•Slide the filter cover in the direction of
the arrow to close it.
Note
•Be sure the filter cover is securely
installed. The power will not turn on
unless it is correctly installed.
•If dust or dirt has collected inside the
bottom air filter (not removable), clean the
filter with a...

Appendix
-83
Maintenance Indicators
■The warning lights on the projector indicate problems inside the projector.
■If a problem occurs, either the temperature warning indicator or the lamp indicator will illuminate
red, and the projector will enter the standby mode. After the projector has entered the standby
mode, follow the procedures given below.
Temperature warning
indicator Lamp indicator Power indicator
About the temperature warning indicator
If the temperature inside the pro-
jector increases, due...

-84
Maintenance Indicators
Info
•If the temperature warning indicator illuminates, and the projector enters the standby mode, follow the pos-
sible solutions on the previous page and then wait until the projector has cooled down completely before
plugging in the power cord and  turning the power back on. (At least 5 minutes.)
•If the power is turned off for a brief moment due to power outage or some other cause while using the
projector, and the power supply recovers immediately after that, the lamp...

Appendix
-85
Lamp
■It is recommended that the lamp (optional: AN-C55LP) be replaced when the remaining lamp life
becomes 5% or less, or when you notice a significant deterioration in the picture and color quality.
The lamp life (percentage) can be checked with the on-screen display. See page 70.
■Purchase a replacement lamp unit of type AN-C55LP from your place of purchase, nearest Sharp
Authorized Projector Dealer or Service Center.
IMPORTANT NOTE TO U.S. CUSTOMERS:
The lamp included with this projector...

Lamp
unitAN-C55LP
User service screw
Removing and Install-
ing the Lamp Unit
Info
•Make sure that you remove the lamp by
the handle. Do not touch the glass sur-
face of the lamp unit or the inside of the
projector.
•To avoid injury to yourself and damage
to the lamp, ensure to carefully follow the
steps below.
•Do not loosen other screws except for the
lamp unit cover and lamp unit.
(Only the silver screws are loosened).
1Press STANDBY on the projector
or 
 on the remote control to
put the projector into...