Singer 2454 Manual

19Faites
connaissance
de votre 
machine Faites
connaissance
de votre 
machine
Conozca 
su
máquina Conozca 
su
máquinaSelectores SelectoresSélecteurs58Sélecteur de longueur du point
Ce sélecteur contrôle lespace entre les points. La 
marque en relief est lindicateur. Le chiffre plus élevé 
donnera le point plus écarté. Consultez les 
ajustements recommandés pour connaître la longueur 
du point la plus indiquée pour votre couture.  Selector del largo de la puntada
Este selector regula el espacio entre los...

20Getting to
know your
machine Getting to
know your
machine1.Raise needle to its highest position.
2.Loosen needle clamp screw and remove needle.
3.With flat side of needle to the back, insert new needle 
up  into clamp as far as it will go.
4.Tighten needle clamp screw securely. Changing needles1.Raise needle to its highest position by turning hand 
wheel toward you.
2.Raise presser foot using presser foot lifter at back of 
machine.
3.Push toe of presser foot (1) up, until it snaps off the 
shank (2)....

RECOMMENDED SETTINGS
Pattern:  Straight stitch (A)
StitchLenght:2-5
   
Foot:Zipper (available at Sewing Centers)
   Adjusting the zipper foot
When the zipper teeth are to the left of the needle 
(illustration 1):
 Slide the adjusting block (A) across to the right.
 Snap-on the foot to the left side of the pin.
When the zipper teeth are to the right of the needle  
(illustration 2):
 Slide the adjusting block (A) across to the left.
 Snap-on the foot to the right side of the pin.211.Eleve la aguja a su...

22Getting to
know your
machine Getting to
know your
machine
12
Changing screw-on 
presser feet with shank1.Raise needle and presser foot.
2.Remove the needle.
3.Loosen presser foot screw (1) and remove presser foot 
with shank (2), guiding it toward you and to the right.
4.To replace presser foot with shank, hook shank around 
the presser bar and tighten presser foot screw with the 
use of a coin.
5.Replace the needle.(For some optional presser feet)55Ojalador OjaladorBoutonnièrePerensatelas:  Especial (...

23Faites
connaissance
de votre 
machine Faites
connaissance
de votre 
machine
Conozca 
su
máquina Conozca 
su
máquina1.Eleve la aguja y el prensatelas.
2.Retire la aguja.
3.Afloje el tornillo (1) y quite el prensatelas (2), 
guiándolo hacia Vd. y a la derecha.
4.Para sustituir el prensatelas, enganche el tronco 
alrededor de la barra prensatelas y ajuste el tornillo 
con una moneda.
5.Recoloque la aguja. 1.Eleve la aguja y el prensatelas.
2.Retire la aguja.
3.Afloje el tornillo (1) y quite el prensatelas...

24Getting to
know your
machine Getting to
know your
machine53
Boutonniére
et boutons Boutonniére
et boutons
Ojales y 
botones Ojales y 
botonesWinding a bobbin is quick and easy when you follow the 
directions below. Always wind the bobbin before 
threading the machine and needle.
1.Place spool of thread on spool pin.
2.Slide spool pin holder (2) firmly over rim of spool to 
prevent thread from tangling.
Note: Use the kind of the holder according the spool 
size. 
3.Lead thread from spool and snap into...

Buttonholes
and
buttons Buttonholes
and
buttonsAttaching a buttonRECOMMENDED SETTINGS
Stitch Width:  Pattern  B  or  C  according to the button
holes distance.
Foot:  Button Sewing (H), available at your local Sewing
  Center.1.Attach feed cover an button sewing presser foot. Raise 
the bobbin thread and pull both threads to the back of 
the presser foot (illustration 1).
2.Place the fabric and button under the presser foot. 
Turn hand wheel toward your direction observing if 
needle in the left side...

341226Preparing
the 
machine Preparing
the 
machinePreparing
the 
machine Preparing
the 
machine511.Raise presser foot.
2.Turn hand wheel toward you until needle is in its 
highest position.
3.Open and remove bobbin visor and remove empty 
bobbin.
4.Pull approximately 4  (10 cm) of thread from 
replacement bobbin and insert bobbin into case 
(illustration 1).
Note: While unwinding, the bobbin should turn from 
right to left.
5.Holding bobbin in place, guide thread into notch (A) 
(illustration 2) and...

21Overcasting is used to prevent the fabric edges to fray 
out. To involve the fabric edges with a stitch, zigzag 
stitching shall be used.
RECOMMENDED SETTINGS
Pattern: Zigzag stitch (B, C, D)
Stitch length: 
Foot: General purpose presser foot (B)
Place fabric under presser foot, positioning the edge 
of the fabric in the center of the foot slot, as shown in 
illustration .
2. Adjust stitch width so that one stitch is inside the 
fabric and the other is out, as shown in illustration 2. 
This procedure...

28Preparing
the 
machine Preparing
the 
machine49
4
1
256731.Raise take-up lever to highest position by 
turning hand wheel toward you.
2.Raise presser foot to release thread 
tension.
3.Place spool of thread on spool pin. Use 
adequate spool pin holder to hold spool 
firmly in place.
4. Slide spool pin holder firmly over rim of 
spool to prevent thread from hangling.
5.Lead thread from spool and snap into thread 
guide (1) and holding thread ends in each 
hands snap thread into upper thread guide, 
as...