Sony Bdv It1000 Operating Instructions

							External Audio Device
101GB
You can enjoy the system’s sound by using the 
S-AIR receiver. The S-AIR receiver can be 
installed anywhere, regardless of the location of 
the unit, for enjoying the system’s sound in 
another room.
For details of the S-AIR receiver, refer to the 
operating instructions of the S-AIR receiver.
1Set the ID of the S-AIR receiver to that 
of the main unit.
 To set the ID of the unit, see “To set the ID 
of the unit” (page 99).
 To set the ID of the S-AIR receiver, refer 
to the operating instructions of the S-AIR 
receiver.
2Press S-AIR MODE on the remote of the 
main unit.
The S-AIR mode appears in the front panel 
display. Each time you press S-AIR 
MODE, the S-AIR mode changes.

: The S-AIR receiver outputs 
sound according to function set on the 
unit.
 “SEPARATE”: You can set the desired 
function for the S-AIR receiver while unit 
functions do not change.
3Select the desired function on the 
S-AIR receiver.
xWhen “PARTY” is set
The S-AIR receiver’s function changes 
sequentially as you press FUNCTION of 
the main unit (page 73).
xWhen “SEPARATE” is set
The S-AIR receiver’s function changes as 
follows.
“MAIN UNIT” t “TUNER FM” t 
“TUNER AM” t “DMPORT” t …
To enjoy the same function as the unit, 
select “MAIN UNIT.”
When “TUNER FM” or “TUNER AM” is 
selected on the unit, you can only select the 
same band for the tuner on the S-AIR 
receiver. In this case, when you select other 
than “TUNER FM” or “TUNER AM” on 
the unit, you can select any band for the 
tuner on the S-AIR receiver.
4Adjust the volume on the S-AIR 
receiver.
Note When the sound is other than 2 channel stereo, multi 
channel sound is downmixed to 2 channel.
 The sound of the S-AIR receiver may be cut off by 
operation of the unit.
To control the system from the 
S-AIR receiver
You can control the system from the S-AIR 
receiver by using the following buttons.
For details, refer to the operating instructions of 
the S-AIR receiver.
Enjoying the system’s sound in 
another room
For the S-AIR receiver
Press Operation
H, X, x, 
./>Share the same operations on the 
remote and unit.
S-AIR CH Change the function of the system.
 
						

							102GB
You can enjoy the S-AIR receiver while the unit 
is in standby mode by setting [S-AIR Standby] 
to [On].
1Press "/1.
The system turns on.
2Press HOME.
The home menu appears on the TV screen.
3Press C/c to select   [Setup].
4Press X/x to select [System Settings], 
then press  .
5Press X/x to select [S-AIR Standby], 
then press  .
6Press X/x to select the desired setting.
 [On]: You can enjoy the S-AIR receiver 
while the unit is in standby mode or turned 
on.

: You cannot enjoy the S-AIR 
receiver while the unit is in standby mode.
7Press .
The setting is made.
Note When you set [S-AIR Standby] to [On], the power 
consumption during the standby mode increases.
 When you turn the system off while [S-AIR Standby] 
is set to [On], “S-AIR” flashes (when sound 
transmission between the unit and S-AIR receiver is 
not established), or lights up (when sound 
transmission between the unit and S-AIR receiver is 
established) in the front panel display.
 If you turn the system off with the disc tray opened 
while [S-AIR Standby] is set to [On], the disc tray 
may not close automatically.
 When the wireless transceiver is not inserted in the 
unit, you cannot set the [S-AIR Standby].
 [S-AIR Standby] is set to [Off] automatically when 
the wireless transceiver is removed from the unit.
When you use the additional surround amplifier 
(optional) with surround back speakers 
(optional), set the SURROUND SELECTOR 
switch to SURROUND BACK. For details 
about the surround back speakers, see “About 
the surround back speaker” (page 38).
It is easy to set the same ID for the unit and an 
S-AIR sub unit, such as a surround amplifier or 
S-AIR receiver, to establish sound transmission. 
However, neighbors may also receive your 
system’s sound if IDs are the same, or you may 
receive the sound from neighbors. To prevent 
this, you can identify the unit with a specific 
S-AIR sub unit by performing the pairing 
operation.
xBefore pairing
Sound transmission is established by the ID 
(example).
Enjoying the S-AIR receiver 
while the unit is in standby 
mode
For the S-AIR receiver
Using the surround amplifier 
for the surround back speakers
For the surround amplifier
Identifying the unit with a 
specific S-AIR sub unit 
(Pairing operation)
For the surround amplifier
For the S-AIR receiver
HDMI S-AIR
This unit
ID A
ID A
S-AIR sub unitID A
S-AIR sub unit Your room
Neighbor
 
						

							External Audio Device
103GB
xAfter pairing
Sound transmission is established between the 
paired unit and S-AIR sub unit(s) only.
To perform pairing
1Place the S-AIR sub unit that you want 
to pair near the unit.
Note Remove headphones from the surround 
amplifier (if connected).
2Match the IDs of the unit and the S-AIR 
sub unit.
 To set the ID of the unit, see “To set the ID 
of the unit” (page 99).
 To set the ID of the surround amplifier, 
see “To set the ID of the surround 
amplifier” (page 100).
 To set the ID of the S-AIR receiver, refer 
to the operating instructions of the S-AIR 
receiver.
3Press HOME.
The home menu appears on the TV screen.
4Press C/c to select   [Setup].
5Press X/x to select [System Settings], 
then press  .
6Press X/x to select [S-AIR Pairing], 
then press  .
The confirmation display appears.
7Press C/c to select [OK], then press 
.
The unit starts pairing.
To not perform pairing, select [Cancel].
8Start pairing of the S-AIR sub unit.
xFor the surround amplifier
Press POWER on the surround amplifier to 
turn on the surround amplifier and press 
PAIRING on the rear panel of the surround 
amplifier.
The PAIRING indicator of the surround 
amplifier flashes red when pairing starts.
When sound transmission is established, 
the PAIRING indicator of the surround 
amplifier turns red and the confirmation 
display appears.
Tip To press PAIRING on the rear panel of the 
surround amplifier, a slim instrument, such as a 
paper clip, can be used.
xFor the S-AIR receiver
Refer to the operating instructions of the 
S-AIR receiver.
When sound transmission is established, 
the confirmation display appears.
Note Perform the pairing within several minutes after 
Step 8. If you do not, the pairing is canceled 
automatically and the confirmation display 
appears. To perform pairing, select [OK]. To 
return to the previous display, select [Cancel].
9Press C/c to select the next operation.
xTo finish pairing
Select [Finish], then press  .
xTo perform pairing of another S-AIR 
sub unit
Select [Continue], then press  .
Note If you perform the pairing operation between the unit 
and another S-AIR sub unit (page 102), sound 
transmission established by ID is canceled.
 When you perform pairing, [(Pairing)] appears beside 
ID on the display for selecting ID.
HDMI S-AIRThis unit
ID A
S-AIR sub unitID A ID A
S-AIR sub unit Your room
Neighbor
PairingNo transmission
 
						

							104GB
To cancel pairing
Perform the ID setting of the unit according to 
the procedure of “To set the ID of the unit” 
(page 99). If you select a new ID (you can select 
the same ID as before), pairing is canceled.
If you use multiple wireless systems which 
sharing the 2.4 GHz band, such as wireless LAN 
or Bluetooth, the transmission of S-AIR 
products or other wireless systems may be 
unstable. In this case, the transmission may be 
improved by changing the following [S-AIR RF 
Change] setting.
1Press HOME.
The home menu appears on the TV screen.
2Press C/c to select   [Setup].
3Press X/x to select [System Settings], 
then press  .
4Press X/x to select [S-AIR RF Change], 
then press  .
5Press X/x to select the desired setting.
: Normally select this. The system 
changes the setting to [On] or [Off] 
automatically.
 [On]: The system transmits sound by 
searching the better channel for 
transmitting.
 [Off]: The system transmits sound by 
fixing the channel for transmitting.
6Press .
The setting is made.
7When you set to [Off], select the ID so 
that sound transmission is most stable 
(page 99).
Note In most cases, you will not need to change this 
setting.
 If [S-AIR RF Change] is set to [Off], transmission 
between the unit and S-AIR sub unit can be 
performed using one of the following channels.
– S-AIR ID A: equivalent channel for Wi-Fi 
channel 1
– S-AIR ID B: equivalent channel for Wi-Fi 
channel 6
– S-AIR ID C: equivalent channel for Wi-Fi 
channel 11
 The transmission may be improved by changing the 
transmission channel (frequency) of the other 
wireless system(s). For details, refer to the operating 
instructions of the other wireless system(s).
If sound transmission is 
unstable
For the surround amplifier
For the S-AIR receiver
 
						

							Other Operations
105GB
Using the Control for 
HDMI Function for 
“BRAVIA” Sync
This function is available on TVs with the 
“BRAVIA” Sync function only.
By connecting Sony components that are 
compatible with the Control for HDMI function 
with an HDMI cable (not supplied), operation is 
simplified as below:
– Theatre Mode (page 106)
– One-Touch Play (page 106)
– System Power Off (page 107)
– Volume Limit (page 107)
– System Audio Control (page 107)
– Language Follow (page 107)
Control for HDMI is a mutual control function 
standard used by CEC (Consumer Electronics 
Control) for HDMI (High-Definition 
Multimedia Interface).
The Control for HDMI function will not work in 
the following cases:
– When you connect this system to a 
component which is not compatible with the 
Control for HDMI function.
– A component does not have an HDMI jack.
There are convenient buttons on the system’s 
remote for operating the TV, such as 
THEATRE, ONE-TOUCH PLAY, AV "/1. For 
details, see “Controlling the TV or Other 
Components with the Supplied Remote” 
(page 111) and refer to the operating 
instructions of the TV.
Note Depending on the connected component, the Control 
for HDMI function may not work. Refer to the 
operating instructions supplied with the component.
 The Control for HDMI function may not work if you 
connect a component other than Sony, even if the 
component is compatible with the Control for HDMI 
function.
(Control for HDMI - Easy Setting)
The system is compatible with the Control for 
HDMI - Easy Setting function. If the TV is 
compatible with the Control for HDMI - Easy 
Setting function, you can set the system’s 
[Control for HDMI] function automatically by 
setting the TV. For details, refer to the operating 
instructions of the TV.
If the TV is not compatible with the Control for 
HDMI - Easy Setting function, set the Control 
for HDMI function of the system and TV 
manually.
Note Displayed items vary depending on the country model.
1Make sure that the system is 
connected to the TV and the connected 
components (which should be 
compatible with the Control for HDMI 
function) using HDMI cables.
2Turn on the TV and press [/1 to turn on 
the system.
3Switch the input selector on your TV so 
that the signal from the system through 
the HDMI input appears on the TV 
screen.
4Set the Control for HDMI function of the 
system and TV.
The Control for HDMI function for the 
system and the connected component is 
simultaneously set to on.
During the setting, “SCANNING” appears 
in the front panel display. After you finish 
the setting, “COMPLETE” appears in the 
front panel display. Wait until the setting is 
complete.
Other Operations
3 2 13 2 1
THEATRE
OPERATION CHANGESTB TV BD
AV
BRAVIA  Sync
ONE-TOUCH
PLAY
Preparing for the Control for 
HDMI function
 
						

							106GB
Note For details on setting the TV and the connected 
components, refer to their operating 
instructions.
If “SCANNING” or “COMPLETE” 
does not appear after performing 
in Control for HDMI – Easy Setting
Set the Control for HDMI function to on for the 
system and the connected components 
individually.
1Press HOME.
The home menu appears on the TV screen.
2Press C/c to select   [Setup].
3Press X/x to select [HDMI Settings], 
then press  .
The options for [HDMI Settings] appear.
4Press X/x to select [Control for HDMI], 
then press  .
5Press X/x to select [On], then press 
.
The Control for HDMI function is set to on.
6Set the Control for HDMI function of the 
connected component to on.
For details on setting the connected 
component, refer to its operating 
instructions.
7Select the input of the system 
connected to the component you want 
to use the Control for HDMI function for 
(HDMI1, HDMI2), and repeat Step 6.
If you add or reconnect the 
component
Perform steps of “Preparing for the Control for 
HDMI function” again.
Note During the setting of the Control for HDMI function 
for the system, the System Audio Control function 
does not work.
 If the Control for HDMI function for the connected 
component cannot be set simultaneously by setting 
“CONTROL FOR HDMI” of the TV, set the Control 
for HDMI function using the menu of the connected 
component.
 For details on setting the TV and the connected 
components, refer to their operating instructions.
Tip The default setting of the Control for HDMI function 
of the system is [Off].
(Theatre Mode)
When you press THEATRE, the system 
automatically switches to the optimum video 
mode for watching movies and the speaker 
output also switches automatically. When 
connected with a Theatre Mode-compatible TV 
using the HDMI cable, the TVs video mode 
switches to Theatre Mode.
(One-Touch Play)
By only pressing ONE-TOUCH PLAY, the TV 
turns on, the TV is set for BD/DVD input 
selector, and the system starts playing a disc 
automatically.
The system and TV work as follows (e.g.):
When playing back a connected component, the 
system and the TV turn on automatically and 
switch to the appropriate HDMI input.
Note Make sure the HDMI connection is correct, and set 
the [Control for HDMI] to [On].
 Depending on the TV, the beginning of the content 
may not be played back.
 Depending on the disc, playback may take a while to 
start.
 One-Touch Play does not work when you press H.
Using the Theatre Mode
Watching BD/DVD by a single 
button press
This system TV
Turns on. (If not already 
turned on.)
r
Switches to “BD/DVD” 
function.
r
Starts playing the disc and 
outputs the sound.Turns on. (If not already 
turned on.)
r
Switches to HDMI input.
r
Minimizes sound level.
(System Audio Control)
 
						

							Other Operations
107GB
(System Power Off)
When you turn the TV off by using the POWER 
button on the TV’s remote or AV "/1 on the 
system’s remote, the system turns off 
automatically.
Note Before using the System Power Off function, set the 
function for TV power. For details, refer to the 
operating instructions of the TV.
 Depending on the status, the system or the connected 
components may not turn off automatically. For 
details, see the operating instructions supplied with 
the connected components.
(Volume Limit)
If you change the output method of the TV to the 
system speaker on the TV menu or by pressing 
THEATRE, loud sound may be output 
depending on the volume level of the system. 
You can prevent this by limiting the maximum 
level of the volume. For details, see [Volume 
Limit] (page 124).
(System Audio Control)
You can enjoy TV sound in this system by easy 
operation.
To use this function, connect the system and the 
TV with an audio cord (not supplied) and an 
HDMI cable (not supplied) (page 57).
You can use the System Audio Control function 
as follows:
 You can enjoy TV sound from the speakers of 
the system by means of a simple operation. For 
details, see the operating instructions of the 
TV. When the system is turned on, the TV sound 
will be output from the speakers of the system.
 When the TV sound is output form the 
speakers of the system, you can adjust the 
volume and turn off the sound of the system 
using the TV remote.
Note If the TV is turned on before turning on the system, 
TV sound will not be output for a moment.
 While the TV is in PAP (picture and picture) mode, 
the System Audio Control function will not work. 
When the TV exits PAP mode, the output method of 
the TV returns to the one before PAP mode.
 When you switch the TV input selector, or depending 
on the status of the connected components, the 
system may switch the input automatically.
Tip You can connect the system and the TV audio 
digitally. For details, see page 57.
(Language Follow)
When you change the language for the on-screen 
display of the TV, the systems on-screen 
display language is also changed after turning 
the system off and on.
Turning the system off in sync 
with the TV
Setting the Maximum Volume 
Level of the System
Enjoying TV sound from the 
speakers in this system
Changing the language for the 
on-screen display of the TV
 
						

							108GB
Calibrating the 
Appropriate Settings 
Automatically
[Auto Calibration]
D. C. A. C. (Digital Cinema Auto Calibration) 
can set the appropriate surround sound 
automatically.
Note The system outputs a loud test sound when [Auto 
Calibration] starts. You cannot turn the volume 
down. Give consideration to children and neighbors.
 Make sure that the headphones are not connected to 
the surround amplifier. You cannot operate the 
following Steps with the headphones connected.
1Press HOME.
The home menu appears on the TV screen.
2Press C/c to select   [Setup].
3Press X/x to select [Audio Settings], 
then press  .
4Press X/x to select [Auto Calibration], 
then press  .
The confirmation display for [Auto 
Calibration] appears.
5Connect the calibration mic to the 
A.CAL MIC jack on the rear panel.
Set up the calibration mic at the ear level 
using a tripod, etc. (not supplied). The front 
of each speaker should face the calibration 
mic, and there should be no obstruction 
between the speakers and the calibration 
mic.
6Press X/x to select [OK].
To cancel, select [Cancel].
COAXIAL OPTICAL
COAXIAL 75FM
AMANTENNA DIGITALHDMI
DMPORTEZW-RT10
TV
SAT/CABLE IN VIDEO OUT IR REMOTE
LAN(100)
EXTERNAL
SPEAKER SAT/CABLE
COMPONENT VIDEO  OUT
COMPONENT VIDEO  IN
A.CAL
MIC
SAT/CABLE TV
IN 1 IN 2 OUTIN
700mA
MAX ECM-AC2 AUDIO INOUT IN
AUDIO
VIDEO Y
YP
B/
PB / CBPR / CRCBPR/
CR
L R
L RDC5V DC5V 500mA  MAX
S-VIDEO VIDEO
FRONT
RFRONT
LCENTER WOOFER
A.CAL
MICE
C
M
-A
C
2
Calibration mic
Ex. BDV-IT1000
 
						

							Other Operations
109GB
7Press .
[Auto Calibration] starts.
The system adjust the speaker setting 
automatically.
Be quiet during the measurement.
Note Before [Auto Calibration], make sure that the 
surround amplifier turns on and you install the 
surround amplifier in the appropriate location. If 
you install the surround amplifier in an improper 
location, such as another room, proper 
measurement will not be obtained.
 When you use the additional surround amplifier 
for the surround back speakers (optional), make 
sure that the additional surround amplifier turns 
on and you install the additional surround 
amplifier in the appropriate location.
 Avoid being in the measurement area and 
making noise during the measurement (about 1 
minute), to avoid measurement failure. During 
the measurement, test signals are output from 
the speakers.
 The environment of the room in which the 
system is installed may affect measurements.
 Loud test sound is output when [Auto 
Calibration] starts. You cannot turn the volume 
down. Give consideration to children and 
neighbors.
 If an error message appears, follow the message, 
then select [OK].
An error message appears when:
– the headphones are connected to the surround 
amplifier.
– the calibration mic is not connected.
– front speakers are not correctly connected.
– surround speakers are not correctly 
connected.
– surround back speakers (optional) are not 
correctly connected.
– subwoofer is not connected.
8Confirm the conclusions of [Auto 
Calibration].
The conclusions appear on the TV screen. 
Press C/c to change the page. The first page 
shows the distance of speakers. The second 
page shows the level of speakers.
Note If measurement fails, follow the message then 
retry [Auto Calibration].
9Press X/x to select [OK] or [Cancel], 
then press  .
xThe measurement is OK.
Disconnect the calibration mic, then select 
[OK]. The result is implemented.
xThe measurement is not OK.
Follow the message, then select [OK] to 
retry.
Note While the Auto Calibration function works:
– do not turn off the power.
– do not press any button.
– do not change the volume.
– do not change the function.
– do not change the disc.
– do not insert or eject a disc.
– do not connect the headphones to the surround 
amplifier.
– do not disconnect the calibration mic.
Tip You can check the distance between the listening 
position and each speaker. See page 110.
 
						

							110GB
Setting the Speakers
[Speaker Settings]
To obtain the best possible surround sound, set 
connection of the speakers and their distance 
from your listening position. Then use the test 
tone to adjust the level and the balance of the 
speakers to the same level.
Note You cannot operate [Speaker Settings] when you 
connect headphones to the surround amplifier.
1Press HOME.
The home menu appears on the TV screen.
2Press C/c to select   [Setup].
3Press X/x to select [Audio Settings], 
then press  .
4Press X/x to select [Speaker Settings], 
then press  .
The [Speaker Settings] display appears.
5Press X/x to select the item, press  .
Setup the following settings.
x[Connection]
If you do not connect center or surround 
speakers, set the parameters for [Center] and 
[Surround]. Since the front speaker and 
subwoofer setting is fixed, you cannot change 
them.
When you use the additional surround amplifier 
for the surround back speakers (optional) 
(page 37), set [Surround Back] also.
[Front]
[Yes]
[Center]
[Yes]: Normally select this.
[None]: Select this if no center speaker is used. 
[Surround]
[Yes]: Normally select this.
[None]: Select this if no surround speaker is 
used.
[Surround Back]
[Yes]: Select this if surround back speaker is 
used.[None]
: Select this if no surround back speaker 
is used.
[Subwoofer]
[Yes]
x[Distance]
When you move the speakers, be sure to set the 
parameters of the distance (A) from the 
listening position to the speakers.
You can set the parameters from 0.0 to 7.0 
meters.
The speakers in the illustration correspond to the 
following:
1Center speaker
2Front left speakers (L)
3Front right speakers (R)
4Subwoofer
5Surround left speakers (L)
6Surround right speakers (R)
7Surround back left speakers (L)
8Surround back right speakers (R)
[Front L/R] 3.0 m: Set the front speaker 
distance.
[Center] 3.0 m
*: Set the center speaker distance.
[Surround L/R] 3.0 m
*: Set the surround speaker 
distance.
[Surround Back L/R] 3.0 m
*: Set the surround 
back speaker distance.
[Subwoofer] 3.0 m
: Set the subwoofer distance.* This item appears when you set to [Yes] in the 
[Connection] setting.
A
A
2
5
786 1
43