Sony Bdv It1000 Operating Instructions

							71GB
Getting Started
12Press X/x to select the setting for the 
Control for HDMI function.
Select [On] to use the [Control for HDMI] 
function (page 105) when connecting Sony 
components that are compatible with the 
Control for HDMI function.
If you do not use the [Control for HDMI] 
function, select [Off].
13Press  or c.
The Setup Display for [BD Internet 
Connection] appears.
14Press X/x to select the setting for the 
BD Internet connections.
Select [Allow] to allow Internet 
connections.
If you do not allow the connections, select 
[Do not allow].
15Press  or c.
The Setup Display for [Standby Mode] 
appears.
16Press X/x to select the standby mode.
You can operate the player quickly after 
turning on this function.
Select [Quick Start] if you want to shorten 
the startup time from the standby mode. The 
default setting is [Normal].
Note Quick Start mode will increase electricity 
consumption and activate the fan in the standby 
mode.
17Press  or c.
The Setup Display for [Auto Calibration] 
appears.
18Connect the calibration mic to the 
A.CAL MIC jack on the rear panel.
Set up the calibration mic at the ear level 
using a tripod, etc. (not supplied). The front 
of each speaker should face the calibration 
mic, and there should be no obstruction 
between the speakers and the calibration 
mic.
On You can operate this unit in conjunction with a TV connected by HDMI.
Check your TV settings when using this function.
Easy Setup - Control for HDMI
COAXIAL OPTICAL
COAXIAL 75FM
AMANTENNA DIGITALHDMI
DMPORTEZW-RT10
TV
SAT/CABLE IN VIDEO OUT IR REMOTE
LAN(100)
EXTERNAL
SPEAKER SAT/CABLE
COMPONENT VIDEO  OUT
COMPONENT VIDEO  IN
A.CAL
MIC
SAT/CABLE TV
IN 1 IN 2 OUTIN
700mA
MAX ECM-AC2 AUDIO INOUT IN
AUDIO
VIDEO Y
YP
B/
PB / CBPR / CRCBPR/
CR
L R
L RDC5V DC5V 500mA  MAX
S-VIDEO VIDEO
FRONT
RFRONT
LCENTER WOOFER
A.CAL
MICE
C
M
-A
C
2
Calibration mic
Ex. BDV-IT1000
 
						

							72GB
Getting Started
19Press X/x to select [OK].
To cancel, select [Cancel].
Note Make sure that the headphones are not 
connected to the surround amplifier. You cannot 
operate the following steps with the headphones 
connected.
20Press .
[Auto Calibration] starts.
The system adjusts the speaker setting 
automatically.
Be quiet during the measurement.
Note Loud test sound is output when [Auto 
Calibration] starts. You cannot turn the volume 
down. Give consideration to children and 
neighbors.
 Before [Auto Calibration], install the surround 
amplifier in the appropriate location. If you 
install the surround amplifier in an improper 
location, such as another room, proper 
measurement will not be obtained.
 Avoid being in the measurement area and 
making noise during the measurement (which 
takes about 1 minute), as it may interfere with 
measurement.
 When you use the surround back speakers with 
the optional surround amplifier, install the 
speakers in appropriate location and turn the 
surround amplifier on.
21Confirm the conclusions of [Auto 
Calibration].
The conclusions appear on the TV screen. 
Press C/c to change the page. The first page 
shows the distance of speakers. The second 
page shows the level of speakers. If the 
conclusions are ok, unplug the calibration 
mic and press X/x to select [OK].
Note The environment of the room in which the 
system is installed may affect measurements.
 If measurement fails, follow the message then 
retry [Auto Calibration].
22Press .
Easy Setup is finished. All connections and 
setup operations are complete.
To quit the Easy Setup
Press HOME in any Step.
Tip If you change the position of the speakers, reset the 
speaker settings. See “Calibrating the Appropriate 
Settings Automatically” (page 108) and “Setting the 
Speakers” (page 110).
 If you want to change any of the settings, see 
“Settings and Adjustments” (page 117).
To recall the Easy Setup Display
1Press HOME.
The home menu appears on the TV screen.
2Press C/c to select   [Setup].
3Press X/x to select [Easy Setup], then 
press .
4Press C/c to select [Start], then press 
.
The Easy Setup display appears.
 
						

							73GB
Getting StartedStep 6: Enjoying Sound 
by Each Function
You can enjoy BD/DVD, TV, Set-top box/
digital satellite receiver, or VCR sound from all 
the speakers in this system.
1Press FUNCTION repeatedly until the 
desired function appears in the front 
panel display.
Each time you press FUNCTION, the 
function changes as follows.
“BD/DVD” t “TUNER FM” t 
“TUNER AM” t “TV” t “SAT/
CABLE” t “HDMI1” t “HDMI2” t 
“DMPORT” t …
Note When you use both the TV (AUDIO IN) jacks 
(analog connection) and DIGITAL IN (TV) jack 
(digital connection), or SAT/CABLE IN 
(AUDIO) jacks (analog connection) and 
DIGITAL IN (SAT/CABLE) jacks (digital 
connection) at the same time, the digital 
connection takes priority.
2Press DECODING MODE repeatedly 
until the decoding mode you want 
appears in the front panel display.
When you want to output the TV sound or 
stereo sound of a 2 channel source from the 
six speakers, select the “PRO LOGIC,” 
“PLII MOVIE,” or “PLII MUSIC” 
decoding mode.
For details, see page 86.
Note Depending on your TV, you may need to turn off your 
TV’s speaker to enjoy surround sound of the system.
Tip When listening to MP3 files or other compressed 
music using the DIGITAL MEDIA PORT adapter, 
you can enhance the sound.
Press DECODING MODE repeatedly until “A.F.D. 
STD” appears in the front panel display (page 86) and 
set the sound mode (page 89) to “MOVIE,” 
“MUSIC,” or “NEWS.”
To cancel, select other than “A.F.D. STD.”
 When using the additional surround amplifier 
(optional) with the surround back speakers (optional), 
you can select “PLIIx MOVIE” and “PLIIx MUSIC” 
for the decoding mode (page 86).
If distortion occurs in the sound 
of a connected component
You can reduce the input level for the connected 
component. For details, see [Attenuate - TV] 
(page 121) and [Attenuate - SAT/CABLE] 
(page 121).
Function Source
“BD/DVD” Disc that is played by the 
system
“TUNER FM”/
“TUNER AM”FM/AM radio (page 92)
“TV” TV
“SAT/CABLE” Component that is 
connected to the SAT/
CABLE jacks on the rear 
panel (page 59)
3 2 1
6 5 4
9 8 7
0
FUNCTION
DECODING
MODE
With the cover opened.
“HDMI1”/“HDMI2” Component that is 
connected to the HDMI1 
or 2 jack on the rear panel 
(page 59)
“DMPORT” DIGITAL MEDIA 
PORT adapter (page 98)
Function Source
 
						

							74GB
Playing a BD/DVD
Depending on the disc, some operations may be 
different or restricted.
Refer to the operating instructions supplied with 
your disc.
1Turn on your TV.
2Switch the input selector on the TV to 
this system.
3Press "/1.
The system turns on.
4Press FUNCTION repeatedly until “BD/
DVD” appears in the front panel 
display.
5Press A.
6Load a disc.
Place one disc on the disc tray, and then 
press A.
When you insert a commercially available 
BD-ROM or DVD VIDEO, playback 
automatically starts depending on the disc.
Note When you play an 8 cm disc, place it on the 
inner circle of the tray. Be careful that the disc is 
not skewed on the inner circle of the tray.
 Do not forcibly press the disc tray closed with 
your finger, as this may cause malfunction.
 Do not place more than one disc on the tray.
7Press C/c to select   [Video].
8Press X/x to select  , then press H 
or .
For commercially available BD-ROM or 
DVD VIDEO, playback starts.
For a BD or DVD recorded on other 
equipment, the title list appears. Press X/x 
to select  , then press H or  .
Playback starts.
9Adjust the volume by using 2 +/– on 
the remote or VOLUME +/– on the unit.
The volume level appears on the TV screen 
and in the front panel display.
Playback
 
FUNCTION VOLUMEZ
HDMI S-AIR
"/1
Disc trayFUNCTION
H
A
VOLUME +/–x
3 2 1
6 5 4
9 8 7
0
"/1
FUNCTION
xH
X./>
2 +/– /
m/M C/X/x/c, 
HOMEOPTIONS A
Number 
buttons ONE-TOUCH
PLAY
TIME
 
DISPLAY
POP UP/
MENU TOP MENUSCENE
SEARCH
A/V SYNC
VideoBD Data
 
						

							Playback
75GB
Note Depending on the system status, the volume level 
may not appear on the TV screen.
 When you set the [Control for HDMI] function to 
[On], the TV that is connected to the system with an 
HDMI cable (not supplied) can be sync-operated with 
the system. For details, see “Using the Control for 
HDMI Function for “BRAVIA” Sync” (page 105).
Tip You can change the speed at which the volume is 
turned up and down.
To turn the volume up/down quickly, press and hold 
the 2 +/– on the remote or VOLUME +/– on the 
unit.
To set the volume up/down precisely, press the 
2 +/– on the remote or VOLUME +/– on the unit 
briefly.
To turn the system off
Press "/1 while the system is on. The system 
enters standby mode.
To save power in standby mode
Press "/1 while the system is on.
To enter power saving mode, make sure that the 
system is in the following status.
– [Control for HDMI] is set to [Off] (page 105).
– [S-AIR Standby] is set to [Off] (page 102).
– [Standby Mode] is set to [Normal] 
(page 126).
To use the headphones
Connect the headphones to PHONES jack on the 
surround amplifier. The sound of the system is 
muted. For details, see page “To enjoy the sound 
by using headphones” (page 67).
Other operations
1)Scan speeds may differ with some discs.2)BD/DVD VIDEO/DVD-RW/DVD-R only.3)BD/DVD VIDEO/DVD-RW/DVD-R/DVD+RW/
DVD+R only.
Note You may not be able to use the instant replay or 
instant advance function with some scenes.
To play a restricted BD or DVD 
(Parental Control)
When you play a restricted BD
Change [BD Parental Control] in [BD/DVD 
Viewing Settings] (page 122).
When you play a restricted DVD
Change [DVD Parental Control] in [BD/DVD 
Viewing Settings] (page 122).
To Press
Stopx
PauseX
Resume play after pauseX or H
Go to the next chapter>
Go back to the 
preceding chapter. twice in a second.
When you press . once, 
you can go to the beginning 
of the current chapter.
Turn off the sound 
temporarily 
To cancel, press it again or 
2 + to adjust the sound 
volume.
Stop play and remove 
the discA
Locate a point quickly 
by playing a disc in fast 
forward or fast reverse 
(Scan)
1)
M or m while playing a 
disc. Each time you press 
M or m during scan, 
the playback speed changes 
as follows:
Playback direction
M1 (×10) t M2 (×30) 
t M3 (×120)
Reverse direction
n (×1) t m1 (×10) t 
m2 (×30) t m3 
(×120)
When you press and hold 
the button, fast forward/fast 
reverse continues at the 
selected speed until you 
release the button.
To return to normal speed, 
press H. Actual speeds 
may differ with some discs.
Replay the previous 
scene
2) (instant replay) during 
playback.
Briefly fast forward the 
current scene
3) (instant advance) 
during playback.
To Press
 
						

							76GB
When you play a restricted BD or DVD, the 
display for entering your password appears on 
the screen.
Enter your four-digit password using the 
number buttons, and press  .
Playback starts.
To register or change the password, see 
[Password] (page 123).
To play a restricted BD-RE or BD-
R (Disc Lock)
When you play a BD-RE or BD-R restricted by 
the Disc Lock function, the display for entering 
your password appears on the screen.
1Enter the four-digit password that has 
been registered when creating the disc 
using the number buttons, and press 
.
2Select a title, and press H or  .
Playback starts.
One-Touch Play (for HDMI 
connection only)
Press ONE-TOUCH PLAY. 
The system and the connected TV turn on and 
the input selector on the TV is switched to the 
system, then you can enjoy the contents of a 
disc.
Note When using the HDMI connection, there may be a 
delay before the playback picture appears on the 
screen, and the beginning portion of the playback 
picture may not be displayed.
  To use the this function, set [Control for HDMI] to 
[On] in [HDMI Settings] (page 124).
Available OPTIONS
1Press OPTIONS.
The options menu appears.
2Press X/x to select an item, then press 
.
The available items differ depending on the 
disc type or system situation.
Items Details
[Video Settings] Adjusts settings for picture 
(page 81).
[Title List] Displays the title list.
[Play] Plays the title from the 
point where you pressed x.
[Play from start] Plays the title from the 
beginning.
[Top Menu] Displays the disc’s Top 
Menu (page 78).
[Menu/Popup Menu] Displays the BD-ROM’s 
Pop-up Menu or DVD’s 
menu (page 78).
[Stop] Stops playback.
[Title Search] Searches for a title and 
starts playback from the 
beginning (page 79).
[Chapter Search] Searches for a chapter and 
starts playback from the 
beginning (page 79).
 
						

							Playback
77GB
 
If various angles (multi-angles) for a scene are 
recorded on a disc, you can change the viewing 
angle.
Press    during playback to select the 
desired angle.
Note Depending on the disc, you may not be able to change 
the angle even if multi-angles are recorded on the 
disc.
 
If subtitles are recorded on a disc, you can turn 
the subtitles on/off during playback. If 
multilingual subtitles are recorded on the disc, 
you can change the subtitle language during 
playback, or turn the subtitles on/off whenever 
you want.
Press   during playback to select the 
desired subtitle language.
Note Depending on the disc, you may not be able to change 
the subtitles even if multilingual subtitles are 
recorded on the disc. You also may not be able to turn 
them off.
When you stop the disc, the system remembers 
the point where you pressed x. As long as you 
do not remove the disc, Resume Play will work 
even if the system is set to standby mode by 
pressing "/1.
1While playing a disc, press x to stop 
playback.
2Press X/x to select  , then press H 
or .
The system starts playback from the point 
where you stopped the disc in Step 1.
Note Depending on where you stop the disc, the system 
may not resume playback from exactly the same 
point.
 The point where you stopped playing may be cleared 
when:
– you open the disc tray.
– you play another title.
– you change the settings on the system.
– you disconnect the AC power cord (mains lead).
– you remove the external memory (for BD-ROMs).
 This function may not work properly with some 
discs.
To play from the beginning of the 
title
Press OPTIONS to select [Play from start], then 
press  . Playback starts from the beginning of 
the title.
Changing the angles
Displaying the subtitles 
Resuming playback from the 
point where you stopped the 
disc
(Resume Play)
 
 
						

							78GB
To display Top Menu
A BD/DVD is divided into a lot of sections, 
which make up a picture or music feature. These 
sections are called “titles.” When you play a BD/
DVD which contains several titles, you can 
select the title you want using Top Menu.
You can also select items such as the language 
for the subtitles and the language for the sound 
using Top Menu.
1Press TOP MENU.
The disc’s menu appears on the TV screen.
The contents of the menu vary depending 
on the disc.
2Press C/X/x/c or the number buttons to 
select the item you want to play or 
change.
3Press .
To display Pop-up Menus
Some BD-ROMs contain Pop-up Menus that 
appear without interrupting playback.
1Press POP UP/MENU during playback.
The Pop-up Menu appears.
2Press C/X/x/c, the color buttons, or 
number buttons to select the item, and 
follow the on-screen instructions.
Some BD-ROMs have bonus contents and other 
data that can be downloaded to the external 
memory (local storage) for enjoyment.
1Press "/1 to turn the system off.
2Insert the external memory (not 
supplied) into the EXTERNAL slot on 
the rear of the unit.
The external memory is used as the local 
storage.
Make sure that the external memory is 
properly inserted into the unit (page 64).
3Press "/1 to turn the system on.
4Insert a BD-ROM with BonusView/BD-
Live.
The operation method differs depending on 
the disc. Refer to the operating instructions 
supplied with the disc.
To delete data in the external 
memory
You can delete unnecessary data.
1Press HOME. 
2Press C/c to select   [Video].
3Press X/x to select [BD Data], then 
press .
4Select the disc name, then press 
OPTIONS.
5Select [Erase], then press  .
6Select [OK], then press  .
The data of the selected disc will be deleted.
Note Depending on the BD-ROM, the disc name may not 
be displayed.
Tip To delete all data in the external memory at once, 
select [Erase All] in Step 5.

  instead of OPTIONS in Step 4 to skip Step 
5.
Using the BD’s or DVD’s menu
 
Enjoying BonusView/BD-Live
 
						

							Playback
79GB
You can move quickly between scenes within 
the title currently being played back.
1Press SCENE SEARCH during 
playback or in pause mode.
Playback pauses and a bar with a scene 
indicator (square-shaped – indicates the 
current point) appears at the bottom of the 
screen.
2Press and hold C/c or m/M to move 
the scene indicator to the scene you 
are searching for.
The scene indicator on the bar is displayed 
around the playing point.
3Release the button at the point you 
want to watch.
The scene at which you released the button 
is displayed in pause mode.
To search for a scene again, move the scene 
indicator using C/c or m/M.
4Press SCENE SEARCH,  , H, or X.
Playback starts.
To cancel Scene Search mode
Press SCENE SEARCH,  , H, or X.
Playback starts from the point you pressed the 
button.
Note The Scene Search function is available for titles 
longer than 100 seconds and shorter than 100 hours.
 Depending on the disc, this function may not work.
You can search for a chapter if the title contains 
chapter marks.
1Press OPTIONS during playback or in 
pause mode.
The options menu appears.
2Press X/x to select a search method, 
then press  .
 [Title Search] (for a BD-ROM/DVD 
VIDEO): Searches the desired title.
 [Chapter Search]: Searches the desired 
chapter.
The display for entering the number 
appears.
Example: Chapter Search
3Press the number buttons to enter the 
number of the title or chapter.
If you make a mistake, press CLEAR, and 
re-enter another number.
4Press .
After a while, the system starts playback 
from the selected number.
To cancel [Title Search]/[Chapter 
Search]
Press RETURN.
Searching for a scene quickly
(Scene Search)
 
Scene Search
The current pointScene indicator
Searching for a Title/Chapter
 
Chapter :
 
						

							80GB
You can check the title information, including 
the video transmission rate, etc.
Press   DISPLAY during playback.
The displayed information differs depending on 
the disc type and system status.
Example: When playing a BD-ROM
AThe current selected angle
BTitle number or name
CThe currently selected audio or subtitle setting
DAvailable functions (  angle/  audio/
 subtitle)
EPlayback information
Displays Disc type/Play mode/Video codec/
Bit rate/Playing status bar/Playing time 
(Remaining time*)
FOutput resolution/Video frequency
* Displayed when you press TIME repeatedly.
Tip You can also check the playback information in the 
front panel display.
 Press  ,  , or  , and you can check each 
type of information.
To view the playing time and 
remaining time in the front panel 
display
Press TIME repeatedly.
Each time you press TIME while playing the 
disc, the display changes: 
1 y 2
1 Playing time of the current title
2 Remaining time of the current title
Some displayed items may disappear after a few 
seconds.
Displaying the playing time 
and play information
 
DDolby Digital PlusA ngleA ngle
Mbps
English