Sony Bdv It1000 Operating Instructions

							41GB
Getting Started
Note on handling the subwoofer
 Do not place your hand into the slit of the subwoofer when lifting it. The speaker driver may be damaged. When 
lifting, hold the bottom of the subwoofer.
 Do not push the top of the subwoofer where the speaker unit is installed.
Slits Subwoofer
Speaker unit
 
						

							42GB
Getting Started
Caution
 Contact a screw shop or installer regarding the wall material or screws to be used.
 Use screws that are suitable for the wall material and strength. As a plaster board wall is especially fragile, attach 
the screws securely to a beam and fasten them to the wall. Install the speakers on a vertical and flat wall where 
reinforcement is applied.
 Sony is not responsible for accident or damage caused by improper installation, insufficient wall strength or 
improper screw installation, natural calamity, etc.
BDV-IT1000
1Decide the installation of the speakers.
Recommended example:
Position the front speakers so that their centers align with the TV. Position the center speaker so 
that the center of the speaker and the TV are aligned.
The surround speakers should be placed as high (or a little higher) than the front speakers.
Tip For details about positioning the speakers, see “Step 2: Positioning the System” (page 37).
Installing the speakers on a wall
Center speaker Front View
Front left speaker (L)
TVFront right speaker (R)
Top View
Front left speaker (L)Front right speaker (R) TV
 
						

							43GB
Getting Started
2Decide the speaker position and mark the screw positions.
You need two screws (not supplied) for each bracket. The following indicates the narrower 
positions of the two screws. 
3Remove the cover(s) from the speaker.
Pry up the cover by inserting a thin, flat object into the slit in the cover. 
Note When assembling, take care not to touch the speaker unit.
For the front/surround speakers For the center speaker
565 mm565 mm
Cover
Slit
Front speakerCenter speaker
Surround speaker
 
						

							44GB
Getting Started
4Connect the speaker cords to the speaker.
Thread the speaker cord through the holes in the bracket (bottom).
Use the speaker cords as follows:
 Front left speaker (L): White
 Front right speaker (R): Red
 Surround left speaker (L): Blue
 Surround right speaker (R): Gray
 Center speaker: Green
The connector and color tube of the speaker cords are the same color as the label of the jacks to be 
connected. Be sure to match the speaker cords to the appropriate terminals on the speakers: the 
speaker cord with the color tube to 3, and the speaker cord without the color tube to #. Do not 
catch the speaker cord insulation in the speaker terminals.
Insert the speaker cords into the speaker terminal of the speaker as far as they will go. Ensure that 
the cords are secure by gently pulling on them one at a time.
Note When assembling, take care not to touch the speaker unit.
Tip When removing the speaker cords from the speaker terminals, pull out the speaker cords while pressing the 
white button on the speaker terminal with a tool such as a flathead screwdriver.
Connector
Front speakerCenter speaker
Surround speakerLeft side Color tubeEx. Front speaker
Check the polarity on the label.
 
						

							45GB
Getting Started
5Attach the baffle cover to the speaker.
Use the baffle cover (short) for the front speaker and center speaker, baffle cover (long) for the 
surround speaker. Press the ends of the baffle cover over the pin(s), then press down to flush fit 
the speaker front.
Baffle cover (short)
Baffle cover (long)“J” mark Surround speaker
Front speaker
Center speaker
Baffle cover (short)
 
						

							46GB
Getting Started
6Attach the bracket (bottom) to the speaker.
Insert the bracket (bottom) into the speaker tightly.
Note When attaching the bracket, take care not to catch the speaker cord between the speaker and bracket.
 When assembling, take care not to touch the speaker unit.
7Attach the bracket (top) to the speaker.
Insert the bracket (top) into the speaker and secure it with the screw (supplied).
Note When assembling, take care not to touch the speaker unit.
Ex. Front speaker
Bracket (bottom)
Speaker cord
Front speakerCenter speaker
Surround speakerRight side Bracket (top) Screw
 
						

							47GB
Getting Started
8Secure the speaker to the wall.
Check the horizontal and vertical position and tightly attach the speaker to the wall (making sure 
the wall is sufficiently thick) using two suitable screws for each bracket  (not supplied) in order 1 
and 2.
Note When attaching the speaker, take care not to catch the speaker cord between the speaker and the wall.
 When assembling, take care not to touch the speaker unit.
9Attach the bracket cover to the speaker.
Slide the bracket cover from the front of the speaker.
2
11
2
Front/Surround speakerCenter speaker
Center speakerBracket cover
Front/Surround speaker
 
						

							48GB
Getting Started
10Attach the grille to the speaker.
Be careful with the orientation of the grille. The SONY logo should be at the bottom of the grille 
for the front/surround speaker, and at the left side of the grille for the center speaker.
Note When assembling, take care not to touch the speaker unit.
 Do not push on the attached grille. It may cause damage to the speaker unit.
“SONY” mark GrilleCenter speaker
Front/Surround speakerGrille
“SONY” mark
 
						

							49GB
Getting Started
BDV-IS1000
1Prepare screws (not supplied) that are suitable for the holes of the bracket.
2Secure the bracket to the wall using hole 1.
Tip To prevent the speaker from rotating, use the hole 2, too.
3Remove the rear cap using the wrench (supplied), and remove the speaker pedestal 
using a screwdriver (+) (not supplied).
Note The removed screw is used in a later step. Be sure not to lose the screw.
1
34 2
Rear cap Wrench (supplied)
Screw
 
						

							50GB
Getting Started
4Push A with the supplied wrench (1), and then remove the speaker cords (2).
5Thread the speaker cords through hole 3.
6Reconnect the detached speaker cords, matching 3/# to the appropriate speaker 
terminals (1), and then push the lever down completely (2).
Tip If it is difficult to push the lever down, use the wrench (supplied).
(1)
When the lever is down, the 
speaker cords are locked.When the lever is up, the 
speaker cords can be removed. (2)A
3
#3 (1)(2)