Standard Horizon Receiver Phantom Series PS1000 Operating Instructions

Page 11 Phantom PS1000
2. Connect the red power wire to a 13.8 VDC ±20% power source. Connect
the black power wire to a negative ground.
3. If an optional remote extension speaker is to be used, refer to next section
for connections.
4. It is advisable to have a Certified Marine Technician check the power output
and the standing wave ratio of the antenna after installation.
8.3 CMP25 RAM+ MICROPHONE INSTALLATION
1. Connect the RAM+ MIC Cable to the RAM MIC CONNECTOR on the rear
panel of the Phantom...

 Phantom PS1000 Page 12
RAM+ or External Speaker Selection
By default the CMP25 RAM+ internal speaker is turned on, however using the
RAM+ mic this speaker can be turned off so the external speaker can be used.
1. Press and hold down the [
CALL(
SET)
MENU]
 key until
“
RADIO SETUP” menu appears.
2. Press the [
CALL(
SET)
MENU]
 key, then press the [

]
 or
[
]
 key to select “
EXT SPK” menu.
3. Press the [
CALL(
SET)
MENU]
 key.
4. Press the [
]
 or [

]
 key to turn the External Speaker “
on.”
5....

Page 13 Phantom PS1000
8.5  CONNECTION OF GPS WITH NMEA OUTPUT
• The GPS must have the NMEA Output turned on and set to 4800 Baud in
the setup menu. If there is a selection for parity select none.
• For further information on interfacing /setting up your GPS. Please contact
the manufacturer of the GPS receiver.
•Phantom PS1000 can read NMEA-0183 version 2.0 or higher.
• The NMEA supported sentences are:
Input: GLL, GGA, RMC and GNS (RMC sentence is recommended)
Output: DSC and DSE
(DSC sentences to...

 Phantom PS1000 Page 14
8.7  CHANGING THE TIME OFFSET
A GPS supplies UTC time to the radio. To show the correct time an offset will
need to be entered using the following proceedure.
1. Press and hold down the [
CALL(
SET)
MENU]
 key until
“
RADIO SETUP” menu appears.
2. Press the [
CALL(
SET)
MENU]
 key, then press the [

]
 or
[
]
 key to select “
TIME” menu.
3. Press the [
CALL(
SET)
MENU]
 key.
4. Press the [

]
 or [
]
 key to select time offset from UTC.
See illustration below to find your offset...

Page 15 Phantom PS1000
8.8  CHANGING COG TO TRUE OR MAGNETIC
Allows customizing the NAV data showing GPS Course Over Ground (COG).
Factory default is “True,” however, following the steps below the COG can be
changed to “Magnetic.”
1. Press and hold down the [
CALL(
SET)
MENU]
 key until
“
RADIO SETUP” menu appears.
2. Press the [
CALL(
SET)
MENU]
 key, then press the [

]
 or
[
]
 key to select “
MAGNETIC” menu.
3. Press the [
CALL(
SET)
MENU]
 key.
4. Press the [

]
 or [
]
 key to select “
on...

 Phantom PS1000 Page 16
8.10  OPTIONAL MMB-84 FLUSH MOUNT INSTALLATION
1. To assist in flush mounting, a template has been included. Use this tem-
plate to find the mounting location.
2. Use the template to mark the location where the rectangular hole is to be
cut. Confirm the space behind the dash or panel is deep enough to accom-
modate the transceiver (at least 15 cm deep).
There should be at least 1 cm between the transceiver’s heatsink and any
wiring, cables or structures.
3. Cut out the rectangular...

Page 17 Phantom PS1000
MEMO 

 Phantom PS1000 Page 18
9  CONTROLS AND INDICATORS
NOTE
This section defines each control, switch, and connector of the Phan-
tom PS1000 Transceiver and CMP25 RAM+ Microphone. For detailed
operating instructions refer to section “10. BASIC OPERATION.”
9.1  PHANTOM PS1000 TRANSCEIVER 

Page 19 Phantom PS1000
PWR key
NOTE
The Phantom PS1000 is designed to be flush mounted or bracket
mounted in a dry cool area when there is limited mounting areas. When
it is bracket mounted the power switch on the Phantom PS1000 is not
used instead use the PWR key located on the top of the RAM+ mic(s).
Turns the transceiver on and off. To turn the transceiver on, press and hold
this key until this switch illuminates orange. To turn it off, press and hold this
ke y until the illumination turns off. When...

 Phantom PS1000 Page 20
9.2  CMP25 RAM+ MICROPHONE
SQUELCH CONTROL (
SQL)
Activates the squelch adjusting
mode.
Press this key to activate the squelch
adjusting mode. Press the [
]
 or [

]
key to adjust the squelch.
VOLUME KEY (
VOL)
Activates the volume adjusting
mode.
Press this key to activate the volume
adjusting mode. Press the [
]
 or [

]
to adjust the volume.
POWER SWITCH (
PWR)
Press and hold down this key to turn
to the transceiver and RAM+ Mic on
and off.
PTT (
Push-To-Talk)
 SWITCH...