Standard Horizon Receiver Phantom Series PS1000 Operating Instructions

							Page 11 Phantom PS1000
2. Connect the red power wire to a 13.8 VDC ±20% power source. Connect
the black power wire to a negative ground.
3. If an optional remote extension speaker is to be used, refer to next section
for connections.
4. It is advisable to have a Certified Marine Technician check the power output
and the standing wave ratio of the antenna after installation.
8.3 CMP25 RAM+ MICROPHONE INSTALLATION
1. Connect the RAM+ MIC Cable to the RAM MIC CONNECTOR on the rear
panel of the Phantom PS1000, then tighten the Cable Nut (See Figure 2).
2. Referring to Figure 3, make a 1.2” (30 mm) hole in the wall, then insert  the
RAM+ MIC Cable into this hole. Connect the Gasket and Mount Base to the
RAM+ MIC Cable Connector using the Nut.
3. Drill the four Screw holes (approx. 2 mm) on the wall, then install the Mounting
Base to the wall using four screws.
4. Connect the CMP25 RAM+ Microphone to the RAM+ MIC Cable Connec-
tor. The installation is now complete.
5. Wires for a external speaker are provided on the RAM+ mic cable. Connect
any 8 Ohm external speaker. When connected the RAM+ controls the vol-
ume level of this speaker.
Wall
Gasket
Mounting Bracket RAM MIC CableCap
Nut
EXP SP Cable for the RAM+ MIC
Figure 2
Figure 3 
						

							 Phantom PS1000 Page 12
RAM+ or External Speaker Selection
By default the CMP25 RAM+ internal speaker is turned on, however using the
RAM+ mic this speaker can be turned off so the external speaker can be used.
1. Press and hold down the [
CALL(
SET)
MENU]
 key until
“
RADIO SETUP” menu appears.
2. Press the [
CALL(
SET)
MENU]
 key, then press the [

]
 or
[
]
 key to select “
EXT SPK” menu.
3. Press the [
CALL(
SET)
MENU]
 key.
4. Press the [
]
 or [

]
 key to turn the External Speaker “
on.”
5. Press the [
CALL(
SET)
MENU]
 key to store the selected set-
ting.
6. Press the [
16/9]
 key to return to radio operation.
8.4  ACCESSORY CABLE
Blue: NMEA IN (+) from GPS navigation receiver
Green: NMEA IN (–) from GPS navigation receiver
Gray: NMEA OUT (+) to GPS navigation receiver
Brown: NMEA OUT (–) to GPS navigation receiver
When connecting the GPS navigation receiver, strip off about 1 inch (2.5 cm) of
the specified wire’s insulation, then splice the ends together using proper wa-
terproofing techniques.
Wire Color/Description
BLUE- NMEA Input (+)
GREEN - NMEA Input (–)
GRAY- NMEA Output (+)
BROWN-NMEA Output (–)
Connection Examples
Connect to NMEA (+)
 output of GPS
Connect to NMEA (–)
 output of GPS
Connect to NMEA (
+)
 input of GPS
Connect to NMEA (–)
 input of GPS
GPS Receiver
Green Blue NMEA OUT
NMEA OUT
NMEA IN
NMEA IN(  )
(  )(  )
(  ) Gray
Brow n 
						

							Page 13 Phantom PS1000
8.5  CONNECTION OF GPS WITH NMEA OUTPUT
• The GPS must have the NMEA Output turned on and set to 4800 Baud in
the setup menu. If there is a selection for parity select none.
• For further information on interfacing /setting up your GPS. Please contact
the manufacturer of the GPS receiver.
•Phantom PS1000 can read NMEA-0183 version 2.0 or higher.
• The NMEA supported sentences are:
Input: GLL, GGA, RMC and GNS (RMC sentence is recommended)
Output: DSC and DSE
(DSC sentences to Standard Horizon Plotter for Position Polling)
If you have further inquires, please feel free to contact Product Support at:
Phone: (800) 767-2450
Email: 
[email protected]
8.6  CHECKING GPS CONNECTIONS
After battery, GPS and the RAM+ microphone(s) have been connected, press
the power switch on the Phantom PS1000 and press and hold the power key
on a RAM+ mic, a small satellite icon will apper on the top right
corner of the LCD display. To see additional GPS information,
press the [
NAV]
 key momentarily. The Phantom PS1000 shows
“time,” “latitude,” and “Longitude” alternately every two seconds.
To hide the navigation information, press the [
NAV]
 key again.
Manufacturer/Model
Lowrance Portable
Magellan Fixed Mount
Magellan Portable
Northstar
Raytheon 420
Raytheon 520 / 620
Raytheon RL SERIES
Simrad
Sitex Neptune, Nautilus
Wires
Orange
Black (GND)
Gray
Black (GND)
Orange
Black (GND)
Yellow
Black (GND)
Yellow
Brown
Blue
Brown
White
Brown
White
Brown
Gray
Brown
PS1000
Blue
Green
Blue
Green
Blue
Green
Blue
Green
Blue
Green
Blue
Green
Blue
Green
Blue
Green
Blue
Green
Wires
Green
Blue
Brown
White
Blue
White
Black
Blue
Black (GND)
Brown
Black (GND)
Yellow
Green
Green
Black
White
Black
White
Black (GND)
Manufacturer/Model
STANDARD HORIZON
Furuno GP30, 36
Furuno GP1650, 1850
Garmin Fixed Mounts
Garmin Portables
JRC GPS500
JRC 100 SERIES
JRC 200 SERIES
Lowrance Fixed Mount
PS1000
Green
Gray
Blue
Blue
Green
Blue
Green
Blue
Green
Blue
Green
Blue
Green
Blue
Green
Blue
Green
Blue
Green 
						

							 Phantom PS1000 Page 14
8.7  CHANGING THE TIME OFFSET
A GPS supplies UTC time to the radio. To show the correct time an offset will
need to be entered using the following proceedure.
1. Press and hold down the [
CALL(
SET)
MENU]
 key until
“
RADIO SETUP” menu appears.
2. Press the [
CALL(
SET)
MENU]
 key, then press the [

]
 or
[
]
 key to select “
TIME” menu.
3. Press the [
CALL(
SET)
MENU]
 key.
4. Press the [

]
 or [
]
 key to select time offset from UTC.
See illustration below to find your offset time from UTC. If
“
00” is assigned, the time is the same as UTC (Universal
Time Coordinated or GMT Greenwich Mean Time).
5. Press the [
CALL(
SET)
MENU]
 key to store the time offset.
6. Press the [
16/9]
 key to return to radio operation.
OFFSET TIME TABLE 
						

							Page 15 Phantom PS1000
8.8  CHANGING COG TO TRUE OR MAGNETIC
Allows customizing the NAV data showing GPS Course Over Ground (COG).
Factory default is “True,” however, following the steps below the COG can be
changed to “Magnetic.”
1. Press and hold down the [
CALL(
SET)
MENU]
 key until
“
RADIO SETUP” menu appears.
2. Press the [
CALL(
SET)
MENU]
 key, then press the [

]
 or
[
]
 key to select “
MAGNETIC” menu.
3. Press the [
CALL(
SET)
MENU]
 key.
4. Press the [

]
 or [
]
 key to select “
on (Magnetic)” or “of
(True).”
5. Press the [
CALL(
SET)
MENU]
 key to store the selected set-
ting.
6. Press the [
16/9]
 key to return to radio operation.
8.9  CHANGING GPS INFORMATION TO
VESSEL POSITION OR COG
Allows customizing the NAV data showing GPS Information. Factory default is
“Your Vessel’s Current Position,” however, following the steps below the GPS
Information can be changed to Cruise Information (COG: Course Over Ground
and SOG: Speed Over Ground).”
1. Press and hold down the [
CALL(
SET)
MENU]
 key until
“
RADIO SETUP” menu appears.
2. Press the [
CALL(
SET)
MENU]
 key, then press the [

]
 or
[
]
 key to select “
NAV DISPLAY” menu.
3. Press the [
CALL(
SET)
MENU]
 key.
4. Press the [

]
 or [
]
 key to select “
Pos (Your Vessel’s Cur-
rent Position)” or “
Cru (Course Over Ground).”
5. Press the [
CALL(
SET)
MENU]
 key to store the selected set-
ting.
6. Press the [
16/9]
 key to return to radio operation. 
						

							 Phantom PS1000 Page 16
8.10  OPTIONAL MMB-84 FLUSH MOUNT INSTALLATION
1. To assist in flush mounting, a template has been included. Use this tem-
plate to find the mounting location.
2. Use the template to mark the location where the rectangular hole is to be
cut. Confirm the space behind the dash or panel is deep enough to accom-
modate the transceiver (at least 15 cm deep).
There should be at least 1 cm between the transceiver’s heatsink and any
wiring, cables or structures.
3. Cut out the rectangular hole and insert the transceiver.
4. Fasten the brackets to the sides of the transceiver with the lock washer nut
combination; so that the mounting screw base faces the mounting surface
(see Figure 4).
5. Turn the adjusting screw to adjust the tension so that the transceiver is tight
against the mounting surface.
Figure 4. MMB-84 Flush Mount Installation
BracketAdjusting Screw
Lock-washer nut combination 
						

							Page 17 Phantom PS1000
MEMO 
						

							 Phantom PS1000 Page 18
9  CONTROLS AND INDICATORS
NOTE
This section defines each control, switch, and connector of the Phan-
tom PS1000 Transceiver and CMP25 RAM+ Microphone. For detailed
operating instructions refer to section “10. BASIC OPERATION.”
9.1  PHANTOM PS1000 TRANSCEIVER 
						

							Page 19 Phantom PS1000
PWR key
NOTE
The Phantom PS1000 is designed to be flush mounted or bracket
mounted in a dry cool area when there is limited mounting areas. When
it is bracket mounted the power switch on the Phantom PS1000 is not
used instead use the PWR key located on the top of the RAM+ mic(s).
Turns the transceiver on and off. To turn the transceiver on, press and hold
this key until this switch illuminates orange. To turn it off, press and hold this
ke y until the illumination turns off. When the power is turned on, the trans-
ceiver is set to the last selected channel.
This switch is connected in parallel with the switch with the same name on
the front panel of the CMP25 RAM+ Microphone.
RAM+ MIC CONNECTOR
Connects the Phantom PS1000 to the CMP25 RAM+ Microphone.
ACCESSORY CONNECTION CABLE
Connects the Phantom PS1000 to a GPS. See section “3. OPTION” for a list
of speakers STANDARD HORIZON offers.
DC INPUT CABLE
Connects the radio to a DC power supply capable of delivering 12V DC.
ANTENNA JACK
Connects an antenna to the transceiver. Use a marine VHF antenna with
an impedance of 50 ohms. 
						

							 Phantom PS1000 Page 20
9.2  CMP25 RAM+ MICROPHONE
SQUELCH CONTROL (
SQL)
Activates the squelch adjusting
mode.
Press this key to activate the squelch
adjusting mode. Press the [
]
 or [

]
key to adjust the squelch.
VOLUME KEY (
VOL)
Activates the volume adjusting
mode.
Press this key to activate the volume
adjusting mode. Press the [
]
 or [

]
to adjust the volume.
POWER SWITCH (
PWR)
Press and hold down this key to turn
to the transceiver and RAM+ Mic on
and off.
PTT (
Push-To-Talk)
 SWITCH
Activates transmission.
[
H/L]
 KEY
Toggles between high and low power. When the [
H/L]
 key is pressed while
the transceiver is on channel 13 or 67, the power will temporarily switch
from “LO” to “HI” power until the PTT is released. The [
H/L]
 key does not
function on transmit inhibited and low power only channels.
[
] 
/ [

]
 KEY
These keys are used to select channels, adjust the volume and squelch
level, and to choose the item selection of different functions (such as the
DSC operation).
[
16/9]
 KEY
Immediately recalls channel 16 from any channel location. Holding down
this key recalls channel 9. Pressing the [
16/9]
 key reverts to the previous
selected working channel.
Secondary use
Press and hold the [
16/9]
 key then press the [
WX]
 key to switch the USA,
International or Canadian channels.
SCAN DW
NAVWX
CA LL
SETME M IC
U.I.C
M
E
NU16
9