Standard Horizon Receiver Phantom Series PS1000 Operating Instructions

							Page 41 Phantom PS1000
6. Press the [

]
 or [
]
 key to select the first letter of the name
of the group you want to reference in the directory.
7. Press the [
CALL(
SET)
MENU]
 key to store the first letter in
the name and step to the next letter to the right.
8. Repeat step 6 and 7 until the name is complete. The name
can consist of up to eleven characters, if you do not use all
eleven characters press the [
CALL(
SET)
MENU]
 key to move
to the next space. This method can also be used to enter a
blank space in the name. To clear the previous letter, press the [
H/L]
 key.
9. After the eleventh letter or space has been entered,
press and hold the [
CALL(
SET)
MENU]
 key to ad-
vance to the MMSI (Maritime Mobile Service Iden-
tity Number) number entry.
10. Press the [

]
 or [
]
 key to select the first digit of the MMSI
number, then press the [
CALL(
SET)
MENU]
 key to move to
the next digit. If a mistake was made entering in the number, pressing the
[
H/L]
 key to delete the wrong digit.
11. Repeat step 10 as many times as necessary to com-
plete the MMSI code (nine digits).
12 Press and hold the [
CALL(
SET)
MENU]
 key to store
the group address.
13. To enter another group address, repeat steps 5 through 12.
14. To exit this menu and return to radio operation mode press
the [
16/9]
 key.
11.7.2 Transmitting a Group Call
1. Press the [
CALL(
SET)
MENU]
 key. The DSC Op-
eration menu will appear.
2. Press the [

]
 or [
]
 key to select “
GROUP” menu,
then press the [
CALL(
SET)
MENU]
 key. The trans-
ceiver will beep, and the “Group directory” will ap-
pear. (To cancel, press the [
16/9]
 key)
3. Press the [

]
 or [
]
 key to select the “Group” you
want to contact.
4. Press the [
CALL(
SET)
MENU]
 key to transmit the
Group DSC signal.
5. After the GROUP CALL is transmitted, all the radios
in the group will switch to the designated channel.
6. Listen to the channel to make sure it is not busy, then key
the microphone and call the other vessels you desire to com-
municate with. 
						

							 Phantom PS1000 Page 42
11.7.3 Receiving a Group Call
1. When a group call is received, “RECEIVED GROUP” will ap-
pear on the LCD, and a ringing alarm sound.
2. The radio automatically switches to the requested channel.
3. Press any key to stop the alarm.
4. Press the [

]
 or [
]
 key to see the MMSI of the vessel
transmitting the Group Call.
5. Monitor the channel for the person calling the Group for a
message.
6. If you want to respond, monitor the channel to make sure it is clear, then
press the PTT on the mic and talk to the calling ship(s).
NOTE
After a Group call is received, the time the call was made and the ships
MMSI or vessels name will appear on the LCD.
11.8  POSITION REQUEST
Advancements in DSC have made it possible to poll the location of another
vessel and show the position of that vessel on the display of the Phantom
PS1000. Standard Horizon has taken this feature one step further, if any Stan-
dard Horizon GPS is connected to the Phantom PS1000, the polled position of
the vessel is shown on the display of the GPS chart plotter making it easy to
navigate to the location of the polled vessel. This is a great feature for anyone
wanting to know the position of another vessel. For example your buddy that is
catching fish, or finding the location of a person you are cruising with.
NOTE
The other vessel must have an operating GPS receiver connected to its
DSC transceiver and must not have its transceiver set to deny position
requests.  (Refer the section “11.6.1 Setting up the Individual / Posi-
tion Call Directory” to enter information into the individual directory).
11.8.1 Setting up Position Reply
The Phantom PS1000 can be set up to automatically or manually send your
position to another vessel. This selection is important if you are concerned
about someone polling the position of your vessel that you may not want to. In
the manual mode you will see the MMSI or persons name shown on the display
allowing you to choose to send your position to the requesting vessel. 
						

							Page 43 Phantom PS1000
1. Press and hold down the [
CALL(
SET)
MENU]
 key
until “
RADIO SETUP” menu appears.
2. Press the [

]
 key to select “
DSC SETUP” menu,
then press the [
CALL(
SET)
MENU]
 key.
3. Press the [

]
 or [
]
 key to select “
POS REQUEST”
menu, then press the [
CALL(
SET)
MENU]
 key.
4. Press the [

]
 or [
]
 key to select “
Au” or “oF.”
In “
Au” mode, after a DSC Position Request is re-
ceived, the radio will automatically transmit your vessels po-
sition. In “
oF” mode, the CMP25 RAM+ Microphone’s dis-
play will show who is requesting the position.
5. Press the [
CALL(
SET)
MENU]]
 key to store the selected setting.
6. To exit this menu and return to radio operation mode press the [
16/9]
 key.
The PS1000 has the capability to turn off the Position Request ringer.
1. Press and hold down the [
CALL(
SET)
MENU]
 key
until “
RADIO SETUP” menu appears.
2. Press the [

]
 key to select “
DSC SETUP” menu,
then press the [
CALL(
SET)
MENU]
 key.
3. Press the [

]
 or [
]
 key to select “
DSC BEEP” menu,
then press the [
CALL(
SET)
MENU]
 key.
4. Press the [

]
 or [
]
 key to select “POS REQUEST,”
then press the [
CALL(
SET)
MENU]
 key.
5. Press the [

]
 or [
]
 key to select “oF.”
6. Press the [
CALL(
SET)
MENU]
 key to store the se-
lected setting.
7. To exit this menu and return to radio operation mode
press the [
16/9]
 key.
If you wish to return to enabling the ringer tone, just repeat the above proce-
dure, pressing the [

]
 or [
]
 key to select “on” in step “5” above.
11.8.2 Transmitting a Position Request to Another Vessel
1. Press the [
CALL(
SET)
MENU]
 key. The DSC Op-
eration menu will appear.
2. Press the [

]
 or [
]
 key to select “
POS REQUEST”
menu, then press the [
CALL(
SET)
MENU]
 key. The
transceiver will beep, and the “Position Request direc-
tory” will appear. (To cancel, press the [
16/9]
 key)
3. Press the [

]
 or [
]
 key to select the “name” you
want to contact.
4. Press the [
CALL(
SET)
MENU]
 key to transmit the 
						

							 Phantom PS1000 Page 44
Position Request DSC signal.
5. After a DSC position request is transmitted, the trans-
ceiver remains on channel 70 until position data is
received from the polled vessel.
6. When the Phantom PS1000 receives the position
from the polled vessel, 
RECEIVED POS REPLY” will
appear on the LCD.
7. Press the [

]
 or [
]
 key to see the name and posi-
tion (LAT/LOG) of the vessel polled vessel.
8. If the Phantom PS1000 does not receive a reply,
the LCD will display “
NO REPLY.” Press the [

]
 key
and select “
SEND” to transmit the call again or “EXIT”
to exit the Position Request mode.
NOTE
If the Phantom PS1000 does not receive position data
from the polled vessel, the LCD will show “
NO POSITION
DATA
.”
11.8.3 Receiving a Position Request
When a position request call is received from another vessel, a ringing alarm
will sound and POS REQUEST will be show in the LCD. Operation and trans-
ceiver function differs depending on the setting of section “11.8.1 Setting up
Position Reply.”
Automatically reply:
1. When a position request call is received, a calling alarm
sounds 4 times. Then requested position coordinates are
transmitted automatically to the vessel requesting your ves-
sels position.
2. To exit from position request display, press any key.
Manually reply:
1. When a position request call is received from an-
other vessel,  “
RECEIVED POS REQUEST” will ap-
pear on the LCD and a ringing alarm sounds 4 times.
2. Press the [

]
 key to see the MMSI of the vessel
transmitting the Position Request. 
						

							Page 45 Phantom PS1000
3 Select type of reply function “SEND” or “NO REPLY”
by using the [

]
 or [
]
 key.
4. When “
SEND” is selected, press the
[
CALL(
SET)
MENU]
 key. And your position will be
transmitted to the requesting vessel.
5. To exit from position request display, press the [
16/9]
 key.
11.9  POSITION SEND
The feature is similar to Position Request, however instead of requesting a
position of another vessel this function allows you to send your position to an-
other vessel. Your vessel must have an operating GPS receiver connected for
the Phantom PS1000 to send the position.
11.9.1 Setting up a Position Send Ringer
The PS1000 has the capability to turn off the Position Send ringer.
1. Press and hold down the [
CALL(
SET)
MENU]
 key
until “
RADIO SETUP” menu appears.
2. Press the [

]
 key to select “
DCS SETUP” menu,
then press the [
CALL(
SET)
MENU]
 key.
3. Press the [

]
 or [
]
 key to select “
DSC BEEP” menu,
then press the [
CALL(
SET)
MENU]
 key.
4. Press the [

]
 or [
]
 key to select  “
POS SEND”
menu, then press the [
CALL(
SET)
MENU]
 key.
5. Press the [

]
 or [
]
 key to select “
oF.”
6. Press the [
CALL(
SET)
MENU]
 key to store the se-
lected setting.
7. To exit this menu and return to radio operation mode
press the [
16/9]
 key.
If you wish to return to enabling the ringer tone, just repeat the above proce-
dure, pressing the [

]
 or [
]
 key to select “
on” in step “5” above.
11.9.2 Transmitting a DSC Position Send Call
1. Press the [
CALL(
SET)
MENU]
 key. The DSC Op-
eration menu will appear.
2. Press the [

]
 or [
]
 key to select “
POS SEND” menu,
then press the [
CALL(
SET)
MENU]
 key. The trans-
ceiver will beep, and the “Position Send directory”
will appear. (To cancel, press the [
16/9]
 key)
3. Press the [

]
 or [
]
 key to select the “name” you
want to contact.
4. Press the [
CALL(
SET)
MENU]
 key to send your position
to the selected vessel. 
						

							 Phantom PS1000 Page 46
11.9.3 Receiving a DSC Position Send Call
When another vessel transmits their vessels location to the PS1000 the follow-
ing will happen:
1. When the Position Send Call is received, “
RECEIVED POS
SEND
” will appear on the LCD and a ringing sound will be
produced.
2. Press any key to stop ringing.
3. Press the [

]
 or [
]
 key to see the name and posi-
tion (LAT/LOG) of the of the vessel transmitting the
Position Send Call. 
						

							Page 47 Phantom PS1000
MEMO 
						

							 Phantom PS1000 Page 48
12  RADIO SETUP
12.1 LCD DIMMER
This selection sets up the display backlight intensity or to turn it off. Default
setting is level “3.”
1. Press and hold down the [
CALL(
SET)
MENU]
 key until
“
RADIO SETUP” menu appears.
2. Press the [
CALL(
SET)
MENU]
 key, then press the [

]
 or
[
]
 key to select “
DIMMER” menu.
3. Press the [
CALL(
SET)
MENU]
 key.
4. Press the [

]
 or [
]
 key to select the desired level. You will
be able to see the effects of your changes. The dimmer
level can be set from “
0 (off)” to “3.”
5. Press the [
CALL(
SET)
MENU]
 key to store  the selected level.
6. Press the [
16/9]
 key to return to radio operation.
12.2 LCD CONTRAST
This selection sets up the display for best viewabilty for the operation. Default
setting is level “4.”
1. Press and hold down the [
CALL(
SET)
MENU]
 key until
“
RADIO SETUP” menu appears.
2. Press the [
CALL(
SET)
MENU]
 key, then press the [

]
 or
[
]
 key to select “
CONTRAST” menu.
3. Press the [
CALL(
SET)
MENU]
 key.
4. Press the [

]
 or [
]
 key to select the desired level. You will
be able to see the effects of your changes. The contrast
level can be set from “
0” to “7.”
5. Press the [
CALL(
SET)
MENU]
 key to store the selected level.
6. Press the [
16/9]
 key to return to radio operation. 
						

							Page 49 Phantom PS1000
12.3 TIME OFFSET
This selection sets the time offset between local time and UTC (time GPS
sends to radio). Time is displayed when GPS position (LAT/LON) is displayed
by pressing the [
NAV]
 key. Default setting is level “00.”
1. Press and hold down the [
CALL(
SET)
MENU]
 key until
“
RADIO SETUP” menu appears.
2. Press the [
CALL(
SET)
MENU]
 key, then press the [

]
 or
[
]
 key to select “
TIME” menu.
3. Press the [
CALL(
SET)
MENU]
 key.
4. Press the [

]
 or [
]
 key to select time offset from UTC.
See illustration below to find your offset time from UTC. If
“
00” is assigned, the time is the same as UTC (Universal
Time Coordinated or GMT Greenwich Mean Time).
5. Press the [
CALL(
SET)
MENU]
 key to store the time offset.
6. Press the [
16/9]
 key to return to radio operation.
OFFSET TIME TABLE 
						

							 Phantom PS1000 Page 50
“True” mode “Magnetic” mode
12.4  CHANGING GPS INFORMATION TO
VESSEL POSITION OR COG
Allows customizing the NAV data showing GPS Information. Factory default is
“Your Vessel’s Current Position,” however, following the steps below the GPS
Information can be changed to “Course Over Ground (COG).”
1. Press and hold down the [
CALL(
SET)
MENU]
 key until
“
RADIO SETUP” menu appears.
2. Press the [
CALL(
SET)
MENU]
 key, then press the [

]
 or
[
]
 key to select “
NAV DISPLAY” menu.
3. Press the [
CALL(
SET)
MENU]
 key.
4. Press the [

]
 or [
]
 key to select “
Pos (Your Vessel’s Cur-
rent Position)” or “
Cru (Course Over Ground).”
5. Press the [
CALL(
SET)
MENU]
 key to store the selected set-
ting.
6. Press the [
16/9]
 key to return to radio operation.
12.5  CHANGING COG TO TRUE OR MAGNETIC
Allows customizing the NAV data showing GPS Course Over Ground (COG).
Factory default is “True,” however, following the steps below the COG can be
changed to “Magnetic.”
1. Press and hold down the [
CALL(
SET)
MENU]
 key until
“
RADIO SETUP” menu appears.
2. Press the [
CALL(
SET)
MENU]
 key, then press the [

]
 or
[
]
 key to select “
MAGNETIC” menu.
3. Press the [
CALL(
SET)
MENU]
 key.
4. Press the [

]
 or [
]
 key to select “
on (Magnetic)” or “of
(True).”
5. Press the [
CALL(
SET)
MENU]
 key to store the selected set-
ting.
6. Press the [
16/9]
 key to return to radio operation.
In the “True” mode, the display shows direction with “
T.” Mean-
while, the the display shows with “
M” in the “Magnetic” mode.