Telrad Digital Telrad Avanti 3020, 3015d Set User Guide
Here you can view all the pages of manual Telrad Digital Telrad Avanti 3020, 3015d Set User Guide. The Telrad Digital manuals for Telephone are available online for free. You can easily download all the documents as PDF.
Page 11
4 Avanti 3020 and Avanti 3015D sets is active. Pressing this button when the telephone is idle changes the display contrast. [FLASH] Depending on system programming, this button is used to disconnect or to send Flash Signal to the connected remote exchange. Programmable buttons The following buttons on your set have already been pro- grammed to perform specific functions. The System Administrator can program these buttons to perform other functions. If the function of certain buttons does not match...
Page 12
Avanti 3020 and Avanti 3015D sets 5 DN buttons DN buttons are buttons associated with specific Directory Numbers. The first DN button is your Primary DN button, which has the same number as your extension. The Primary DN but- ton is used for making and receiving most of your calls. Whenever you pick up the handset, your Primary DN but- ton, or - if it is not available - another DN button lights green. If no DN buttons are available, no DN button lights, you do not receive dial tone, and you cannot...
Page 13
6 Avanti 3020 and Avanti 3015D sets NOTE for each applicable feature. Consult your System Administrator for further details about the programming of your telephone set. Outside line buttons One or more of the buttons on your telephone may be associated with either specific lines or outside line groups. To access a line for dialing outside the system, press an outside line button. Floating buttons Calls on outside lines for which no button has been defined, may be associated with a button just for...
Page 14
Avanti 3020 and Avanti 3015D sets 7 DISTINCTIVE RINGING You can program telephone sets located close to each other with distinctive rings, to enable you to identify which telephone is ringing. Nine different rings are available. To change the ring for your telephone set 1. Press [*] and [#] simultaneously. 2. Press one of the dialpad buttons ([1] - [9] ). When you hear the ring that you want: 3. Press [#] . 4. Lift and replace the handset. Your telephone set re-initializes and all telephone rings...
Page 15
8 Avanti 3020 and Avanti 3015D sets MUTE If you want to talk to someone in your office during a call, without the connected party hearing, you can disable the handset or telephone set microphone. To enable or disable the microphone (MUTE) • Press [MUTE] during a conversation. To enable or disable the handset microphone (HANDSET MUTE) During a handset call: • Press [HS MUTE] (if programmed). NOTE If your set is Single Audio Path (SAP), pressing [MUTE] deactivates both microphones. ALLOWING OTHER...
Page 16
Avanti 3020 and Avanti 3015D sets 9 HOT DIALPAD The hot dialpad enables you to dial and activate features without lifting the handset or pressing [SPKR] first. NOTE The instructions in this guide assume that you have hot dialpad capability. 3020&3015D.txt.book Page 9 Tuesday, August 3, 1999 1:14 PM
Page 17
10 Avanti 3020 and Avanti 3015D sets INTERNAL CALLS To place a non-ringing call • Dial the extension number. To place a ringing call 1. Dial tone access code [1] . 2. Dial the extension number. If the extension you called is busy (CALLBACK) When you dial an extension and hear busy tone, you can activate the Callback feature: 1. On the Avanti 3020, press {CALL BACK}. On the Avanti 3015D, press {CLLBCK}. When the called extension becomes available, your tele- phone rings. Then: 2. Press [SPKR] or lift...
Page 18
Avanti 3020 and Avanti 3015D sets 11 BARGE INTO A CONVERSATION Depending on system programming you may be able to break into another conversation.When you dial an exten- sion and hear busy tone: • On the Avanti 3020, press {BARGE IN}. On the Avanti 3015D, press {BRG IN}. A warning tone is heard by all parties, depending on system programming. PAGE CALLS You can make announcements through an external page unit, or through the speakers of all DIGITAL telephones in a page zone. 1. Press [FEATURE] ....
Page 19
12 Avanti 3020 and Avanti 3015D sets ANSWERING CALLS When you receive a call an indicator flashes green on a telephone set that is programmed with DN buttons. For internal calls the top line of the display shows the name of the caller and their extension number. For external calls the display shows the trunk name and number. You usually also hear a ring, unless your set has been programmed not to ring. NOTE On outside line calls: Telrads DIGITAL systems support Caller Name and Caller...
Page 20
Avanti 3020 and Avanti 3015D sets 13 CALL WAITING You may hear either a ring or a beep, indicating a second call, while already engaged in a conversation. You can answer the call without disconnecting the first call. To answer a second call 1. Press [HOLD] ; The first call is put on hold. The indicator for that line flashes green. 2. Press the DN or outside line button that is flashing green; you receive the second call. To return to the first call 1. Press [HOLD] ; 2. Press the flashing DN...