Toshiba D-r17dt User Manual

21EN
IntroductionConnectionsBasic Setup Playback
EditingOthers Function Setup
Recording
Note
• Because HDMI is an evolving technology, it is 
possible that some devices with an HDMI input may 
not operate properly with this unit.
• When using an HDCP-incompatible display device, 
the image will not be viewed properly.
• Among the devices that support HDMI, some 
devices can control other devices via the HDMI 
connector; however, this unit cannot be controlled 
by another device vice the HDMI connector.
•...

22EN
Digital Audio for Better Sound Quality 
The connections illustrated above are 
optional for better sound.
1For clear digital sound quality, use 
the DIGITAL AUDIO OUTPUT 
(COAXIAL) jack to connect your 
digital audio equipment.
If the audio format of the digital output does not 
match the capabilities of your receiver, the 
receiver will produce a strong, distorted sound or 
no sound at all.
Connecting a Dolby Digital™ decoder, DTS 
decoder or MPEG decoder
• Connecting multi-channel Dolby Digital...

23EN
Introduction ConnectionsBasic SetupPlayback
EditingOthers Function Setup
Recording
Initial Setting
Turn on this unit for the first time, you need to follow 
these steps.
1Press [ ON / STANDBY].
2Turn the TV on. Select the input to 
which the unit is connected.
3Select your desired channel preset 
type using [U / D]. Then press 
[ENTER/OK].
The unit will start getting channels available in 
your area.
Digital tuning:
Only the DVB channels receivable in your area 
are automatically scanned and...

24EN
Auto Tuning (ANALOG)
Programme the tuner to scan only the channels you 
can receive in your area.
1In stop mode, press [SETUP]. Select 
“General Setting” using [U / D], 
then press [ENTER/OK].
General Setting Menu will appear.
2Select “Channel” using [U / D], then 
press [ENTER/OK].
3Select “ANALOG Channel Setup” 
using [U / D], then press 
[ENTER/OK].
4Select “Auto Tuning” using [U / D], 
then press [ENTER/OK].
The unit will start storing channels available in 
your area.
Wait for several minutes...

25EN
Introduction ConnectionsBasic SetupPlayback
EditingOthers Function Setup
RecordingThis unit can receive the Hyper and Oscar 
frequency bands.
• If “Skip” is set to “ON”, select “Skip” using 
[U / D], then press [P]. Select “OFF” using 
[U / D], then press [L].
• If you want to decode scrambled signals, select 
“Decoder” using [U / D], then press [P]. Select 
“ON” using [U / D], then press [L].
• To store another channel, repeat steps 5 to 8.
9After completion, press [SETUP] to 
exit.
To Skip a...

26EN
Manual Tuning (DVB)
You can preset a DVB channel manually and 
individually.
1Follow steps 1 to 3 in “Auto Tuning 
(DVB)” on page 25.
2Select “Manual Tuning” using 
[U  / D ], then press [ENTER/OK].
3Select your desired position number 
using [U  / D ], then press 
[ENTER/OK].
• The tuner will begin to search up or down  automatically. When a DVB channel is found, 
the unit will stop searching.
 When “Auto” is selected the unit will search for  the channels which have not been stored in 
channels...

27EN
Introduction ConnectionsBasic SetupPlayback
EditingOthers Function Setup
Recording
TV Title List
You can create 4 different favourite lists (TV1 - TV4) 
with your preferred DVB channels and radio stations. 
By setting the certain favourite list, you can loop 
channels only within the list when you use 
[PROG.  / ].
1Follow steps 1 to 3 in “Auto Tuning 
(DVB)” on page 25.
2Select “Edit Channels” using 
[U / D], then press [ENTER/OK].
3Select the DVB channel you want to 
add to the favourite list...

28EN
TV View Operation
The following operations are available while viewing 
TV channels through this unit’s tuner.
Selecting the Audio Mode
You can switch between TV audio modes by pressing 
[AUDIO ]  on the remote control. Each mode is 
indicated on the TV screen.
 During reception of analogue bilingual broadcasts
 During the reception of DVB broadcast, when you 
press  [AUDIO ] , sound track display will appear. 
Press  [AUDIO ]  repeatedly to change the sound 
track. 
 If the programme does not...

29EN
Introduction ConnectionsBasic SetupPlayback
EditingOthers Function Setup
Recording
EPG (Electronic Programme Guide)
Electronic programme guide (EPG) gives you a list of 
DVB programmes and detailed information about the 
programmes. To call up EPG (Electronic Programme 
Guide), while viewing DVB/analogue channel or 
external input (AV1/AV2/AV3), press [GUIDE].
You can also call up EPG by following steps.
1In stop mode, press [SETUP]. Select 
“Timer Programming” using [U / D], 
then press [ENTER/OK]....

30EN
Language Setting
1Follow steps 1 to 2 in “PINCODE 
Setting for Adult Lock” on page 29.
2Select “Language” using [U / D ], 
then press [ENTER/OK].
3Select the item you want to change 
the language using [U  / D], then 
press [ENTER/OK].
Audio : Set the Audio language
Subtitle : Set the Subtitle language
Data Service: Set the Digital Teletext language
4Select a language using [ U / D ], 
then press [ENTER/OK].
5Press [SETUP] to exit.
Note
• You can also change the audio language using  [AUDIO ]  if it...