Toshiba D Vr7kc2 Owner Manual

							91EN
Disc 
Management
Recording
Playback
Introduction
Connections
Basic Setup
Editing
Function Setup
VCR Function
Others
1 OSD Language (Default : English)
Set  the l anguage  for the  on-screen d isplay.
Use [K / L] to select a language, then press [ENTER].
OSD Language
English
Français
Español
Your  setting  will be activated.
2 Screen Saver (Default : 10 minutes)
Set  the  time  to activate  the screen  saver function  on the 
TV  screen.
Use [K / L] to select a setting, then press [ENTER].
Screen Saver
OFF
1 minute
5 minutes
10 minutes
15 minutes
Your  setting  will be activated.
3 FL Dimmer (Default: Bright)
Set  the  front p anel display  brightness.
Use [K / L] to select a setting, then press [ENTER].
FL Dimmer
Bright
Dark
You can choose  one from “ Bright”  or “Dark”.
The d isplay  will not l ight  up when  the unit  is in  standby 
mode.  This is a Power Saving mode (ECO) for standby.
4
  Press [SETUP] to exit.
Press [STOP  C] if you  are playing  back a disc.
1
  Press [SETUP] and use [K / L] to 
select “General Setting”, then press 
[ENTER].
2
 Use [K / L] to select “Display”, then press [ENTER].
3
 Use [K / L] to select a desired item, then press [ENTER].
Submenu  will appear.
OSD Language
Screen Saver
FL Dimmer123
Display
GENERAL SETTING
OPEN/
CLOSE INPUT
SELECT HDMI
.@/: ABC GHI
PQRS TUV
SPACE
SETUP DISPLAY AUDIO TIMER
PROG.
DISC MENU
CLEAR RETURN TOP MENU
WXYZ
JKL MNO DEF
ENTER
INSTANT
SKIP
PLAY
DVD
VCR
PAUSE REV
SKIP
STOPSKIP
FWD
1.3x/0.8x
PLAYTIME SLIP
TIMER SET ZOOM
SEARCH
REPEAT REC
REC MODE
DUBBING CH
ENTER
SETUP
STOP




&1($%@%73,$@&/@WJOEE


 


 



 
						

							92 EN
GENERAL SETTING
1 Progressive (Default : OFF)
This unit is compatible  with the p rogressive  scan system. 
The  feature p rovides you with  the higher d efinition 
images  than the traditional  output system d oes. To utilize 
this  feature,  you must  set progressive  scan mode  to “ON”.
1)  Use [K / L ] to select “ON“, then press [ENTER].
Progressive
ON
OFF
2)  Use [{ / B] to select “Yes“, then press [ENTER].
Activating progressive scan:
Check your TV has progressive scan
and connect with component video cable.
NOTE : 
  If there is no picture or picture is
  distorted after selecting “Yes”,
  Wait about 15 seconds for auto recovery.
Activate?                                 Yes  No
3)  Use [K / L] to select “Yes“ within 15 seconds, then press [ENTER].
Your  setting  will be activated.
Note
• If your TV is  compatible with p rogressiv e scan  (480p) , you  
are  recommend ed  to  use  the HDMI or  component v id eo  
cabl e (commercially  a vail abl e) to  connect  this unit  to the  
TV.  (Refer  to pages  21-22.) I f not,  use the RCA vi deo  cabl e 
and  set the p rogressiv e scan  to “OFF”.
• If  the  Progressive S can image  is distorted,  you can 
cancel  Progressive S can by p ressing  and holding 
[SETUP]  for more  than 3 seconds d uring DVD 
playback. T he “Progressive”  setting will be “OFF”.
• When  selecting “No ” or  not p ressing  any buttons  on 
the  unit  or remote  control within 15 second s at  step 3, 
p rogressiv e scan  remains  to be “ OFF”  (interl ace scan).  
2 TV Aspect (Default: 16:9 Wide)
You can select  the TV aspect  ratio to match  the formats  of 
what  you are playing  back with the unit  and your TV 
screen  (4:3 standard  or 16:9 widescreen TV).
Use [K / L] to select a desired option, then press [ENTER].
TV Aspect
4:3 Letter Box
4:3 Pan & Scan
16:9 Wide
If you have a standard TV:
Select “4:3 Letter  Box”, so that  black  bars appear  on the 
top  and  bottom  of the TV screen  when playing  back a 
wide-screen p icture. Select “4:3 Pan & Scan”  for a full 
height p icture with both  sides  trimmed  when playing 
back  wide-screen p icture.
If you have a widescreen TV: Select “16:9 Wide”.
Press  [STOP  C] if you  are playing  back a disc.
1
  Press [SETUP] and use [K / L] to 
select “General Setting”, then press 
[ENTER].
2
 Use [K / L] to select “Video”, then press [ENTER].
3
 Use [K / L] to select a desired item, then press [ENTER].
Progressive
TV Aspect
Select Video123
Submenu  will appear.
4
 Refer 1 to 2 on this page and set 
the selected item.
• For 3,  refer  to “Connection  to an External 
Device“  on page 47.
5
  When you finish with the setting, 
press [SETUP] to exit.
Video
OPEN/
CLOSE INPUT
SELECT HDMI
.@/: ABC GHI
PQRS TUV
SPACE
SETUP DISPLAY AUDIO TIMER
PROG.
DISC MENU
CLEAR RETURN TOP MENU
WXYZ
JKL MNO DEF
ENTER
INSTANT
SKIP
PLAY
DVD
VCR
PAUSE REV
SKIP
STOPSKIP
FWD
1.3x/0.8x
PLAYTIME SLIP
TIMER SET ZOOM
SEARCH
REPEAT REC
REC MODE
DUBBING CH
ENTER
SETUP
STOP




&1($%@%73,$@&/@WJOEE


 


 



 
						

							93EN
Disc 
Management
Recording
Playback
Introduction
Connections
Basic Setup
Editing
Function Setup
VCR Function
Others
3
 Use [K / L] to select a desired item, 
then press [ENTER].
DivX R
 VOD
DivX Subtitle12
1 DivX®  VOD
This  unit allows  you to play  back the files p urchased  or 
rented  from DivX® VOD  (video-on-demand)  services. The 
files  are available  on the  internet. W hen you p urchase  or 
rent D ivX® VOD  files on the  internet,  you will be asked  to 
enter  an activation/registration  code. This menu  item 
provides  you with  the activation/registration  code.
On  how  to activate  this unit  for the D ivX® VOD  file 
playback, visit  www.divx.com/vod.
Your registration code is :
To learn more visit
www.divx.com/vod DivX
 R VOD
Note
• 
One  registration  code is only v alid for one D ivX® VOD 
file.
• You  must first d ownload  the file from  the internet 
and play  it back  on this  unit  before  you are able  to 
get  another  code.
• You  must follow  this step  every  time you p urchase  or 
rent  a DivX® VOD  file from  the internet.
• For  more  information  for DivX®, please v isit 
http://www.divx.com/vod.
• The  registration  code will be d isplayed  in 8 
characters  consist of numbers  between 0 to 9 and 
capital letters  chosen randomly.
2 DivX Subtitle (Default : OFF)
Set the D ivX® subtitle.
Use [K / L] to select a setting, then press [ENTER].
DivX Subtitle
OFF
English
French
Spanish
German
Italian
Swedish
Your  setting  will be activated.
4
  When you finish with the setting, 
press [SETUP] to exit.
DivX®
1
  Press [SETUP] in stop mode and use [K / L] to select “General Setting”, 
then press [ENTER].
2
 Use [K / L] to select “DivX”, then press [ENTER].
Playback
Display
Video
Recording
Clock
Channel
DivX
HDMI
Reset All
GENERAL SETTING
SE-R0297
OPEN/
CLOSE INPUT
SELECT HDMI
.@/: ABC GHI
PQRS TUV
SPACE
SETUP DISPLAY AUDIO TIMER
PROG.
DISC MENU
CLEAR RETURN TOP MENU
WXYZ
JKL MNO DEF
ENTER
INSTANT
SKIP
PLAY
DVD
VCR
PAUSE REV
SKIP
STOPSKIP
FWD
1.3x/0.8x
PLAYTIME SLIP
TIMER SET ZOOM
SEARCH
REPEAT REC
REC MODE
DUBBING CH
ENTER
SETUP




&1($%@%73,$@&/@WJOEE


 


 



 
						

							94 EN
1
  Press [SETUP] in stop mode and use [K / L] to select “General Setting”, 
then press [ENTER].
2
 Use [K / L] to select “HDMI”, then press [ENTER].
Playback
Display
Video
Recording
Clock
Channel
DivX
HDMI
Reset All
• You  cannot  select HDMI when  an HDMI cable is 
not  connected  or the TV’s  external  input 
channel  is not  set to HDMI.
3
 Use [K / L] to select a desired item, 
then press [ENTER].
Format
HDMI Audio
RGB Range123
4
  When you finish with the setting, press [SETUP] to exit.
1 Format (Default : RGB)
You  can select  the color  space  for HDMI output. 
Set  the  appropriate  color space  for your d isplay d evice.
Use [K / L] to select a setting, then press [ENTER].
•  When  the connected device  is not  compatible  with the 
Y/Cb/Cr, HDMI signal  is output  as RGB  regardless  of the 
setting.
Format
RGB
YCbCr
Your  setting  will be activated.
HDMI
GENERAL SETTING
SE-R0297
OPEN/
CLOSE INPUT
SELECT HDMI
.@/: ABC GHI
PQRS TUV
SPACE
SETUP DISPLAY AUDIO TIMER
PROG.
DISC MENU
CLEAR RETURN TOP MENU
WXYZ
JKL MNO DEF
ENTER
INSTANT
SKIP
PLAY
DVD
VCR
PAUSE REV
SKIP
STOPSKIP
FWD
1.3x/0.8x
PLAYTIME SLIP
TIMER SET ZOOM
SEARCH
REPEAT REC
REC MODE
DUBBING CH
ENTER
SETUP




&1($%@%73,$@&/@WJOEE


 


 



 
						

							95EN
Disc 
Management
Recording
Playback
Introduction
Connections
Basic Setup
Editing
Function Setup
VCR Function
Others
2 HDMI Audio (Default : ON)
If  you d o not  want  to output  the audio  through HDMI 
(when  you digitally  output  the audio  through  the 
COAXIAL DIGITAL AUDIO  OUT jack to your  audio  system, 
etc.),  you can set the HDMI audio  output off.
Use [K / L] to select a setting, then press [ENTER].
•  Set  to “OFF”  when  the HDMI sound  is not  output.
HDMI Audio
ON
OFF
Your  setting  will be activated.
3 RGB Range (Default : Normal)
You  can adjust  the RGB  range  to make  the dark areas  of 
the HDMI images  brighter.
Use [K / L] to select a setting, then press [ENTER].
•  Select “Enhanced“  if the  black-white  contrast is not  clear.
•  This  setting  is effective  only for HDMI RGB  output.
RGB Range
Normal
Enhanced
Your setting  will be activated.
GENERAL SETTING
HDMI (cont’d)




&1($%@%73,$@&/@WJOEE


 


 



 
						

							96 EN
Reset the setting  to default.
1
  Press [SETUP] in stop mode and use 
[K / L] to select “General Setting”, 
then press [ENTER].
2
 Use [K / L] to select “Reset All”, then press [ENTER].
Playback
Display
Video
Recording
Clock
Channel
DivX
HDMI
Reset All
3
  Select “Yes” using [K / L] , then press [ENTER].
Reset to factory default?
Ye sNo
“Are  you sure?”  will appear.  S elect “Yes”  using 
[K / L]  and then p ress [ENTER].
Your  setting  will be initialized.
 Reset  All
Note
• The  settings l isted below  will remain  unchanged 
even  after resetting  to the  factory d efault.
 - Clock  setting
 - Channel  setting
 -  OSD language  setting
 -  Parental lock  setting
 - DivX® VOD  code
 - Timer p rograms
GENERAL SETTING
SE-R0297
OPEN/
CLOSE INPUT
SELECT HDMI
.@/: ABC GHI
PQRS TUV
SPACE
SETUP DISPLAY AUDIO TIMER
PROG.
DISC MENU
CLEAR RETURN TOP MENU
WXYZ
JKL MNO DEF
ENTER
INSTANT
SKIP
PLAY
DVD
VCR
PAUSE REV
SKIP
STOPSKIP
FWD
1.3x/0.8x
PLAYTIME SLIP
TIMER SET ZOOM
SEARCH
REPEAT REC
REC MODE
DUBBING CH
ENTER
SETUP




&1($%@%73,$@&/@WJOEE


 


 



 
						

							97EN
Disc 
Management
Recording
Playback
Introduction
Connections
Basic Setup
Editing
Function Setup
VCR Function
Others
VCR FUNCTIONS
Playback
 Recording
1) Press  [I/y ON/STANDBY] on the remote control or 
the front panel of the unit.
When  you are playing  back a cassette  tape, turn on the 
TV  and  be sure  to select  the input  to which  the unit  is 
connected.
Press [VCR].
2) Insert a prerecorded cassette tape. Press [PLAY B]  to begin playback.
3) During playback, press [PAUSE F]. Playback  will pause  and sound  will be muted.
4) Press  [PLAY  B] to resume playback.
5) Press  [STOP  C] to stop playback.
6) Press  [OPEN/CLOSE  A] to eject the cassette tape.
Note
• When a cassette  tape ends d uring playback,  fast-
forward  or normal  recording,  the unit  will 
automatically  rewind to the  beginning  of the 
cassette  tape. After rewinding  finishes, the unit  will 
eject  the cassette  tape.
• When  a cassette  tape without  erase-protection  tab is 
inserted,  the unit  will start playback  automatically.
• Tracking  will be automatically  adjusted upon 
playback. T o adjust  the tracking  manually, press 
[CH 
 / ].
•  Playback  will stop  when  you change  the output 
mode.
Press [VCR] first.
Before recording, make sure:
•  The d esired channel  is selected  by pressing 
[the Number buttons]  or [CH 
 / ].
•  There  is a cassette  tape with an erase-protection  tab in 
the  unit.
•  The d esired recording  speed is selected  in SP (standard 
playback)  or SLP (super l ong playback)  mode by 
pressing  [REC MODE].
Recording speed:
Tape speed Recording / playback time
Type of tape T60 T120 T160
SP 1hour 2hours 2-2/3hours
SLP 3hours6hours8hours
•  Refer  to pages 43-46 for  instructions on timer  recording.
1) Press  [REC  I] to begin the recording.
To  temporarily  stop recording  or to  resume  it, press 
[PAUSE  F]. After the unit  has been  in pause  mode  for 
5  minutes,  it will  stop  automatically  to protect  the 
cassette  tape and the v ideo  head  from d amage.
2) Press  [STOP  C] when the recording is completed.
Accidental erasure prevention
To prevent  accidental  recording on a 
recorded  cassette tape, remove  its erase-
protection  tab. To record  on it later,  cover 
the  hole  with  cellophane  tape.
erase-protection tab
Caution on using S-video, component, or HDMI 
connection for VCR: 
•  Only  the playback  audio / video  are available  with these 
connections.
•  Under  the conditions l isted below,  the playback  image 
and  audio  cannot  be output. U se the  standard video 
connection,  in such  case;
-   during DVD recording.
•  HDMI video  resolution  cannot be changed  when the 
unit  is in VCR  mode.
 Information on VCR Functions
Note
• This function  is available  only when  the unit  is 
connected  by the VIDEO  OUT jack.




&1($%@%73,$@&/@WJOEE


 


 



 
						

							98 EN
VCR FUNCTIONS
One-touch Timer Recording (OTR)Index Search
This feature  allows you to set  the  recording l ength simply 
by p ressing  [REC I] on the  remote  control.
Press [VCR] first.
1) During normal recording, press [REC I] to begin  the one-touch timer recording.
You  can select  a fixed  recording  time by pressing 
[REC  I] repeatedly.
(0:30)( 1:00)(Normal recording)
(7:30)
(8:00)
When the one-touch timer recording is finished, the 
unit will turn off automatically.
To  change  the recording l ength during the one-touch 
timer  recording, press  [REC I] repeatedly  until the 
desired length  appear.
To  cancel  the one-touch  timer recording  within the 
specified  time, press  [STOP C].
Note
• The remaining  recording time will be d isplayed  on 
the  front p anel display d uring one-touch  timer 
recording.  Press [DISPLAY]  to see  it on  the TV screen.
•  You cannot pause the one-touch timer recording.
• If VCR  the one-touch  timer recording  is completed 
during DVD playback  or recording,  the VCR will be in 
stop  mode  and the DVD keeps  the current  mode.
• Unlike  a timer  recording,  you can p erform  the 
following  operations d uring the one-touch  timer 
recording.
 - 

 Turning  off the p ower  (One-touch  timer recording 
will  be canceled.).
 - Using  [REC I] or [STOP  C].
• When  the one-touch  timer recording  is finished  and 
the p ower  is turned  off, the  unit  will switch  to the 
standby  mode automatically  if a timer  recording  has 
been p rogrammed.  Press [TIMER SET]  to cancel  the 
standby  mode for using  the unit  continuously.
• This  function  is available  only when  the unit  is 
connected  by the VIDEO  OUT jack.
An index  mark will be assigned  at the  beginning  of each 
recording  you make. Y ou may  skip to a specific  marked 
point  by following  the steps  below.
Press [VCR] first.
1) Press [SEARCH] so that “INDEX SEARCH” menu  appears.
2) Using [the Number buttons], enter the number of  recordings you wish to skip within 30 seconds.
 
 INDEX SEAR CH
         03
3) Press  [REV  E], [FWD D] to start index search.
If  you  want  to go  in the  forward direction, press 
[FWD  D].
If  you  want  to go  in the  reverse d irection, press 
[REV  E].
After  index  search,  the VCR  will play  back the cassette 
tape  automatically.
Pro.1 Pro.2 Pro. 3Pro.4 Pro.5
02 01 01 02 03
Beginning 
of tape End 
of tape
CURRENT PROGR
AM
INDEX MARK
Note
• You can make  the index  mark up to 20.
• This  function  is available  only when  the unit  is 
connected  by the VIDEO  OUT jack.




&1($%@%73,$@&/@WJOEE


 


 



 
						

							99EN
Disc 
Management
Recording
Playback
Introduction
Connections
Basic Setup
Editing
Function Setup
VCR Function
Others
VCR FUNCTIONS
Time SearchOther Operations
This  feature  allows you to go  to a specific p oint on a 
cassette  tape by entering  the exact  amount  of time  you 
wish  to skip  in order  to reach  the point.
Press [VCR] first.
1) Press [SEARCH] repeatedly so that “TIME SEARCH”  menu appears.
2) Using [the Number buttons], enter your desired  time to skip within 30 seconds.
You  can set the  time  up to 9:59.
 TIME SEAR CH
       2:50
3) Press  [REV  E], [FWD D] to start time search.
If  you  want  to go  in the  forward direction, press 
[FWD  D].
If  you  want  to go  in the  reverse d irection, press 
[REV  E].
After  time search,  the unit  will play  back the cassette 
tape  automatically.
Note
•  Index search and time search are not available 
during recording.
•  Press  [STOP  C] to stop  the search.
• If  the  end  of the  cassette  tape is reached during 
search,  this unit  will cancel  the search  and rewind  the 
cassette  tape.
• This  function  is available  only when  the unit  is 
connected  by the VIDEO  OUT jack.
Press [VCR] first.
Fast forward:
When  the unit  is in  stop  mode, press  [FWD D] to fast 
forward  the cassette  tape.
Rewind:
When  the unit  is in  stop  mode, press  [REV E] to rewind 
the  cassette  tape.
To cue or review picture during playback (picture search):
Press [REV E], [FWD  D] during playback.
Press  it again  and the unit  will search  in super  high 
speed.  (in the SLP  mode only)
To freeze the picture on TV screen during playback 
(still mode):
Press  [PAUSE  F]. Each time  you p ress the button,  the 
picture  will be forwarded  by one  frame.
If  the p icture  begins  to vibrate v ertically  during  the still 
mod e, stabil iz e  the p icture  by pressing  [CH  / ] on  
remote  control.
If the p icture  is distorted  or rolling v ertically,  adjust the 
vertical  hold control  on your TV, if  equipped.
Counter reset:
Press  [CLEAR]  to reset  the counter  to “0:00:00”.
To playback in slow motion:
Press  [PAUSE  F] d uring playback,  then press [FWD  D].
Press  [FWD  D] or [REV E]  repeatedly during slow 
motion playback  to select  the desired  speed.
Automatic rewind:
When  a cassette  tape is played  back or fast  forwarded  to 
its  end,  the cassette  tape will rewind  to the  beginning, 
stop  and eject  itself.
To repeat a playback indefinitely without touching 
[PLAY  B] (Auto  Repeat  Playback):
D uring  normal playback, press  [REPEAT]. When  a tap e is  
played  to its  end,  the tape will  rewind  to the  beginning  and 
start playback  itself. To cancel  the Auto Repeat Playback,

 
p ress  [REPEAT]  again.
When you playback a cassette tape recorded in Hi-Fi 
stereo:
Press [AUDIO ] on  the  remote  control to select H i-Fi or 
MONO  for playback  sound mode.
•  If  you  have connected  a stereo TV to  this unit,  select “HIFI”.
•  If  you  have  connected  a monaural TV to  this unit,  select 
“MONO”.
HIFIYour Selection
Type of recorded tapenon H i-Fi tapes
H i-F i tapes 
recor ded in 
H i-F i stereo
H i-F i tapes 
recor ded second 
audio p rogram
H
i-F i tapes 
recor ded main 
audio p rogram MONO
M onaura l
L+R
M ain  audio 
program
S econd  audio 
program
M
onaura l
R-channel
L-channel
R
M ain  audio 
pro
 gram
S econd  audio 
program
M
onaura l
L
M ain  audio 
program
S econd  audio 
program
Note
• Still/slow  mode will stop  after 5 minutes  to prevent 
damage  to the  cassette  tape and the v ideo head.
• To  return  to playback  from the picture  search/still/
slow  mode, press  [PLAY B].




&1($%@%73,$@&/@WJOEE


 


 



 
						

							100 EN
TROUBLESHOOTING
Before requesting  service for this  unit,  check  the table  below  for a possible  cause of the p roblem  you are experiencing. 
Some  simple  checks  or a minor  adjustment  on your p art may  eliminate  the problem  and restore p roper operation.
Symptom Remedy
D V
D •
V CR The p
ower d oes not turn  on. • Check that the AC power  cord is connected  securely.
• Check  the breaker  (in case  of power  failure).
•  Press  [TIMER SET]  to cancel  the timer  standby  mode.
There  is no p icture. • Re-connect  the connecting  cords securely.
• Check  if the  connecting  cords are damaged.
• Check  the connection  to your TV (pages 19-22).
• Check  if the p rogressive  scan mode  is set  correctly  according  to your TV 
(page 9 2).
• Switch  the input  selector  on your TV (such  as to “L1”)  so that  the signal 
from  the unit  appears  on the TV screen.
TV

 p rogram  rece ption d oes not fi  ll the 
TV  screen. • T
ry to  set  the  channels  with “Auto Channel  Preset” or “M anual Channel 
Preset ” in “C hannel”  menu (pages  27-28).
• S elect  a channel  of any TV p rogram using  [CH 
 / ].
TV  channels  cannot be changed .• Switch  the input  to TV .
• C onnect  the RF coa xial  cable  correct ly (pages 19-24).
TV program p ictures are distorted. • Check if all  the  connections  are made  correctly  (pages 19-24).
• Adjust TV  antenna.
• Adjust  the picture.  (Refer to the TV
 ’s  instruction  manual.)
•  P lace  the unit  and TV  farther apart.
•  P lace  the TV  and any bunched  RF coa xial  cables  farther  apart.
Playback picture  is distorted. • Keep the device  which  may cause  electrical disturbances,  such as a 
cellular p hone, away.
Playback picture  or TV program from 
the d evice  connected  through the unit 
is d istorted. • If 
the playback picture  output from a DVD player, VCR  or tuner  goes 
through  the unit  before  reaching  your TV, the  copy-protection  signal 
applied  to some p rograms  could affect p icture q uality. D isconnect  the 
playback device  in question  and connect  it directly  to your TV.
The  clock display d oes not appear  on 
the  front p anel display. • Check 
that the AC power  cords connected  securely.
•  (In  case  of power  failure) C heck the breaker  and “Clock”  setting.
• When  the unit  is in  standby  mode, front panel display  is off  because 
Power S aving mode  is applied  to this p roduct.
No  analog TV closed  captions are 
output. • If 
you  are using HDMI connection  to watch  the TV programs  through 
this  unit’s  tuner,  analog TV closed  caption cannot be output. T ry using 
other  connection.
There  is no  sound. • Re-connect  all connections  securely.
• Check  if the  connecting  cord is damaged.
• Check  the connections  to the  amplifier  input.
• Check  if the  input d evice setting  on the  amplifier  is correct.
• When  the unit  is in p ause  mode  or in slow-motion playback  mode, 
sound  is not  output. T his is not  a malfunction.
• When  the unit  is in  fast  forward  or fast  reverse  mode, sound  is not 
output. T his is not  a malfunction.
• If  the  audio  signal does  not come  through  the DIGITAL AUDIO  OUT 
(COAXIAL) j ack, check  the setting  in “Audio  Out” (page 89).
• While  the setup  menu  or timer p rogramming d isplay is shown,  or while 
the  screen  saver is active,  the audio  is muted.
No DTS sound  on digital  output. • Change the setting  menu for “DTS” to “ ON”.
No DTS sound  from analog  output • This unit has no analog  sound output  when playing  back the selected 
DTS  sound  mode.
Nothing  was recorded  even though 
you  set the  timer  setting  correctly. • There 
was a p ower  failure d uring  record ing.
• The  unit’s internal  clock  stoppe d due to a p ower  failure  that l asted  for 
more  than 30 second s.  Reset  the c lock  (p age 30).
• The p rogram  contains  copy p rotection  signals that  restricts  copying.
• The  timer  setting  overl appe d with  another  setting that has p riority.
Timer  recording d oes not start. • No disc is inserted.
•  

A disc  is not  recordable  (finalized DVD- RW/-R, finalized DVD+R,  a fully 
recorded disc,  etc.). 
Timer  recording  is not  complete  or did 
not  start  from  the beginning. • The 
timer  setting  overlapped  with another  setting that has p riority 
(page 46).
•  

Disc  space  was not enough.
•  “Mak e Recording C ompatible“ is not  set to “ ON”,  when  recording  onto 
DVD+RW/+R  that was recorded  on other  unit.




&1($%@%73,$@&/@WJOEE