Toshiba Perception Electronic Business Communications System Installation And Maintenance Manual

Nov. 84 
PRaRAMMINc;(PRELIMINARY) 
EWE 63 
Programhas already been started. 
been reached or St? was entered previously. (REQ = SIT) 
Invalid response. 
53IT or KPT was entered in response to FSQ 
but the SCH entry is 30, 60, or NONE. 
WI? was entered in response to Rn;;, but the program has not 
been started. 
KorrectSTARTTIME& DATE, enter=SiT)  

0 84 PEuxRmMIm(PmNARY) 
PZGE 64 
Authorization Procedure must be 
received, proceed as follows: If an WX response is 
the RCVRport RGO=PCBxmmber, X-Circuit 
1. 
= Ignore line en 
Ctl H= Backspace 
DEL= Stop printing and r&xt.rn to 
DEL DEL= Abort program 
Authorization Prxedure mst be cmpleted. If an VK~ response is 
received, proceed as follows: 
i 7 
3 I8 
t  

NOTES: PRcmmMI:ivG(PRELIMINARY) 
PZGE 65 
1, A mximum of 16 Trunk Groups (normally O-15) are possible. 
If Private 
Lines axe to be equipped, the code VVLn is 
in place of 
2, TKTcannotbechanged,DataBlackmstbe r 
(OUT) and data 
entered. 
3. xx= 
TrunkGroup tobe stepped to if this group is busy. 
4*COSismeaningfulonlyfarT~~SA/DIDT~. 16 CC§groups areprovided 
and aredefined in theClass of ServiceDataBlo&. 
5. List the digits which are to be ignored for the plrpose of Toll/Code 
Restriction. 
digit. These...

* 84 
PRoGRAMMlNG (PREUMINARY) 
PIu;E 66  

e 84 
PRc3csmmNG (PRELIMIWY) 
P&SE 67 
TABLE O-2 
Station Lines/ 
8 Attendant Lines 
5 
m 
Norbtransmission Compensated 
z1 (2mwire facility * 2dB loss 
and not impedance compensated) 
l - 
EZ 
z O Transmission Compensated 
b--z (a-wire facility % 2dB loss 
or impedance compensated Station Lines/ 
Attendant Lines Non 
Non-transmission 
Compensated 
(2.wire facility 
c 2dl3 loss and 
not impendance 
compensated) 
1 
1 ‘NL 
Transmission 
Compensated 
(2-wire facility 
4 2dB loss or 
impedance 
compensated,...

Nov. 84 PRcmAMmNG(PRELIMINARY) 
PAGE 68 
Authorization Procedure mst be completed. If an * response is 
received, proceed as follows: 
NOTE: 
1. NN= 
TrunklXBrnmber, X=Circuitnumber. 
2. YY- Trunk Group Number (O-15 or PUL). 
3. GMNcannotbe changed, Data Blockwstbe removed (OUT) and 
entered. 
4. This pranp?t is *i$ only for n;P PVL, 
ION is the DN assigned to a. px 
kJCis&,:  ; 
: I 
5. is the trunks Night station. This 
can alsobe changed by 
aning forTIE/CCSA/DlD 
.trunks). program to activate 
te...

e 84 PRGRAMMING (PRELIMINARY 
1 ~CSYF~FEX~IATIEVLIDIDCSA TIE 
ll?ORlXIXIXIXfX X X 
Y Y 
1 P&SE 69 
Authorization Procedure mst be completed. If an V?Kn response is 
received, proceed as follows: 
ITEM PROW3 USER EknRY 
ICR Utility #1 or #2 
OK 
DICl, DuJ2 1 
- DISK 
LOADIN - 
w 
I Data Tab1e TYP= TYPE PAR, ACT, AM3 
(DXl.1 2 
I 
-a- 
RT%, MM! 
(DIE21 2 
I 
NOTES: 
1, ICR Utilities are divided bet-en two programs: 
Enter: DLCl Ear PAR (Misc. Parameters) 
-- ___. 
Mrca Code Table) 
AOC (Area/Office Code...

e a4 NG (PRELIMINARY) 
PSE 70 
2. If DICl was entered, possible responses are PAR, KT or A!32 
If DE2 was entered, possible response are KTB or MDT, 
en TYPE is pr 
ted, proceed as foil 
Directory Assistance (555) DAC 
call Allcw 
Directory Assistance (555) 
LDl D NNNNNN (DeleteCodes) 
YOIFN 
I 
I 
Xx (RcuteTable tobeused 
I 
I 
&forms the system if interchangeable codes areused (Officecodes with 
NO/lx format). 
2. Defines the area code in which the system is located. Used for routing 
dialed numbers...

NcYrEs: Nov. 84 
PRZRAMMING (PRETJMINARY) 
P&E 71 
1. ~iclears RN0114 and assigns all area codes to table RN0 15. 
NNOUT. clears RbDNN and assigns area codes frcxn table NN to RND15. 
2,InputareacodestobeaddedtothisRNO. 
format N O/IX are permitted (N=2 9, X=0 9). A maximum of 160 ties in the 
possible area codes. At start-up RN15 contains all 
deleted frcxn RN 15. As codes are added toRNO114, they are automatically 
3. Input codes tobe deleted from this RNO. 
they are automatically added to RNJ 15. As...

Nov. 84 
PRCGRAMMING (PfUILIMINARY) 
PAGE 72 
NWIES: 
1, CUT - Will clear all Rake Tables 
N - Will clear Route Table NN. 
2. Rake definition -- 
 6 routes, Format is: 
XX= Trunk Group = Modify Digits Table to be applied (M-D. Table 
must be entered). 
3. sting Route Schedule data is printed autmatically after the response to 
EQ6 prompt is entered. 
4. Time of day interval for this routing schedule: 
5. Maxhm Ctiinsd entrees for IC3, IC2, LCl is 6 routes. Do not assign the 
.saxne route to store than...