Home > Toshiba > Communications System > Toshiba Perception Electronic Business Communications System Installation And Maintenance Manual

Toshiba Perception Electronic Business Communications System Installation And Maintenance Manual

Here you can view all the pages of manual Toshiba Perception Electronic Business Communications System Installation And Maintenance Manual. The Toshiba manuals for Communications System are available online for free. You can easily download all the documents as PDF.

Page 121

(P 
Returns REQ pr en prin t is 
lete. 
tatusofPCBXXX)--Gives thestatusofall 
location LXX, Mx or ROO), Printout 
d, but 11 list all circuits 
order of circui 
Returns REQ pr en prin t is 
ete. 
CALL TNNX (Set up a monitor link frcxn Trunk 
to the remote test 
center.F--This disusedatar te test center to establish 
Onceamonitor linkhasbeene&abl 
.ishedothertnurkscanbetested. 
The trunk to be tested (B) is siezed by a 
terminal d 
and then the test number that is to be dialed, is entered via the...

Page 122

19 P NG (PRELIMINAPY) 
PAGE 44 
Enter: [CR1 to advance the program 
o STS RLSA indicates that the trunk (A) 
S diSCOM&Xd due to a 
malfunction or soma outside influence, such as the distant end 
going on-hook or a grcund start trunk. 
the program will return to the RE1;2 pr After printing STS RLSA, 
t autcmatically.- 
s point the monitor link test center using 
established and the syst s reguesting the 
to be tested, 
Enter: CALL 
C?NNX=portnusber of the to be tested) 
Indicates that the c 
was received,...

Page 123

19 
e: tor link trunk (A) 
center DN = 730-5000 
Test DN = 730-0002 
t 03) 21 
UNEQ=N3FCBinthat 
UIUS=PCBisqui 
2. Status: IDL=Idle 
lyaisabl 
rtdisabl 
DIS TKMsOftWare disabled 
es faulty 
1 
* nse is 
. 
/  ,   / 1 I 
: 
Level 3 given in the Adhorization Pr 
error e is 
given. 
given in the Authorization pr 
. 
esent 
: 
. 
gives then  

Page 124

6 
Ctl X=Igmre line entered 
3,  

Page 125

Nov. 84 PROGRAMMING (PRJ%IMINARU P?GE 47 
D 
Authorization Procedure rmst be ccmpleted. If an OK response is 
received, proceed as follows: 
Ieast Cost Routinq 
All Paqe Access Cede 
ita nN 17 ill-a 
NOTES: 
1. All Page access code = 1, 2, or 3 digits. 
2. N= number dialed in place of * or V#l. 
3. Bewaxe of conflicts with the numbering plan and access codes--system will 
not always check.  

Page 126

Nov. 84 
PROGRAMMING (PRELIMINARY) PAGE 48 
4. CFDNA TIMER must be > RNA or RNA will prevail. 
5. DPT timer also controls A!IT LPK release. 
6. A IgYtq response allows calls from 
to a Hahdsfree Answerback 
equippedEE?TtobeansweredHands 
7. A *Y* response allows calls from the Attendant to a Handsfree Answerback 
equippedEXTto be answe.redHandsfree. 
8.CtlX= Ignore line entered 
CtlH= 
I3ackspace ,‘ 
DEL = Stop printing and return to REQ 
DELDEL= Abortprogram ,^ 
9~ I‘ ; 
p; 
* 
Authorization Procedure...

Page 127

: 
Nov, 84 
PRGRMMING (PRELIMINARY) 
PzlGE 49 
*I 
I /, 
Ja,.. 
la-1 
h-L--- 
-*. - . 
Call PiT3G$ 
1 Hold-All Calls 
Universe Night 
Charqe Acca 
Flash 
Paqing Zone 
O  4-a P inu Zone 1 
.nff Zone Z I - 
I P 
, I men I I 
1C I 
-- #2 I 
Q#2 
2.(xX= 
Ignore line entered 
Ctl H = Backspace 
DEL 
= Stop printing and return to RFl;z 
D&DEL,= 
Abort program  

Page 128

Nov. 84 
PRCGRAMMI~ (PRELIMINARY) PAGE 50 
Authorization Procedure nust be ccsrrpleted. If an OK response is 
received, proceed as follows: 
NOTES: 
1, NN= PCB location 
2. X = Circuit number 
3. A maxim of two key strips are possible: lo-key EXT = 1; 20-key EXT = 2. 
4. There are 16 different COS groups which are defined in the COS Data BLock. 
5. There are maximum of 32 Call Pick---up Groups, 
6. Classes 0 - 
7 are defined in the Toll Restriction Data Block (DIOL) IQ ~0:; p-* )I 
Program. Class 8 is 0,...

Page 129

Nov. 84 
PRGFGMMING (P-1 PiaGE 51 
I Voice Paqe 
I 
lWTES: 
1. NNN = Direct 
XXX= HuntD 
Distributed,, to remove present DN. 
Also see Station Hunt - 
2. NX is entered in place of the usual hunt DN following the EKT DN 
assignment. 
For exanp?le: N = 
Distributed Bunt Group Number (0 - 
---. ./ 
X =&xnberMmber(1-8) 
j. XXX =?LDN assigned in Trunk Data Block. 
4. Maximum ADL keys for entire system is 250. 
5. Flash key causes a 
6. LmJx= m.sec. flash (line open) to CO line. 
Port number of m to be...

Page 130

Nov. 84 PIuxmmMING(PRELLMINARY) 
PPGE 52 
I I No mrt (destination of the key feature) is assianed 
I 
,A...: --A23 is 250). 
ntered but PUG key already assiqned). 
EREXT 22 PVR NNN, PVN NNN is entered but trunk DN NNN is not yet assiqned. 
I 
! EREKT 23 ! The inmt DN is trunk DN (VCP NNN Hunt DN), 
imm nuher of Display EXTs already assigned bxinaum in 
30).  
Start reading Toshiba Perception Electronic Business Communications System Installation And Maintenance Manual

Related Manuals for Toshiba Perception Electronic Business Communications System Installation And Maintenance Manual

All Toshiba manuals