Toshiba Strata Dk14, Dk40i, Dk424 Programming Manual

							System & Station
Program 70 – Verified Account Code Toll Restriction Assignments
Strata DK Programming 5/993-145
System & Station
Program 70 – Verified Account Code Toll Restriction 
Assignments
Processor Type:DK14, DK40i, All RCTUs
Program Type:System
Initialized Default:000 for all VACNs




  6SNU   +ROG  6SNU +ROG 6SNU+ROG 6SNU+ROG
ProcessorVA C NProcessorVACN
DK14 000~299 RCTUBA/BB 000~299
DK40i 000~299 RCTUC/D 000~299
RCTUA 000~299 RCTUE/F 000~499
VACNVAC Digit 
Restrict CodeVAC Restrict 
CodeVACNVAC Digit 
Restrict CodeVAC Restrict 
CodeVACNVAC Digit 
Restrict CodeVAC Restrict 
Code
VAC Restrict Code (00~10)
00 =No Station Toll Restriction
01 =Area Code Toll Restriction
02 =Area Code Toll Restriction and 0 or 1 as 1st (or 
2nd digit)
03 =Class 1 T.R.07 = Class 5 T.R.SELECT = Verified Account Code 
Number (VACN)
DATA = VAC Digit Restriction
0 = No Digit Restriction
1 = Digit Restriction 
						

							System & Station
Program 70 – Verified Account Code Toll Restriction Assignments
3-146Strata DK Programming 5/99
Program 70 Overview
A Toll Restriction Class can be assigned with this program to each of the 300 Verified Account 
Codes assigned in Program 69. This class of restriction overrides the normal station class of 
restriction assigned in Program 48 when a VAC is entered at the station. The station resumes its 
Program 48 restriction after the call is disconnected.
When a Forced or Voluntary Verified Account Code is dialed at a station after accessing a CO line 
and before dialing a telephone number, the station temporarily assumes the Toll Restriction Class 
assigned to the Verified Account Code. When Program 70 is initialized, all Verified Account 
Codes are assigned as not Toll Restricted (data = 00). Verified Account Code Toll Restriction class 
assignments are not user programmable; so if the assignments are not known, it is recommended to 
assign a number (block) of Verified Account Codes to each type of Toll Restriction class. For 
example: 
VACs 000~050 = no restriction
VACs 051~100 = total restriction
VACs 101~150 = Class 1, etc.
©When stations enter VACs they will be unrestricted. 
©Range programming is not available.
©If dial “0” credit card dialing is allowed, use Program 43 to allow designated stations/CO lines 
credit card calling. 
						

							System & Station
Program 71 – DNIS
Strata DK Programming 5/993-147
System & Station
Program 71 – DNIS
Processor Type:DK40i, all RCTUs
Program Type:System
Initialized Default:All Programs blank
DNIS Addresses
Program 71-0: DID / Tie / DNIS / ANI Lines
Program 71-1~3: DNIS Number and ANI Line Routing Assignments
DNIS/ANI Routing Destinations
ProcessorDNIS AddressANI AddressProcessorDNIS AddressANI Address
DK14 NA NA RCTUBA/BB 000~349 349
DK40i 000~199 199 RCTUC/D 000~499 499
RCTUA 000~199 199 RCTUE/F 000~499 499




  6SNU   +ROG  6SNU  +ROG 6SNU+ROG 6SNU+ROG




  6SNU   +ROG  6SNU +ROG 6SNU+ROG 6SNU+ROG
Route to Ports[PDN][PhDN]DH [DN]ACDIMDU/RMDSNetwork Table
DK40i 0000~0027 0500~0527 0900~0915 NA #031 #300~#399
RCTUA 0000~0031 0500~0531 0900~0915 NA #035 #300~#399
RCTUBA/BB 0000~0079 0500~0589 0900~0915 #090~#097 #085 #300~#499
RCTUC/D 0000~0239 0500~0739 0900~0915 #250~#265 #245 #300~#599
RCTUE/F 0000~0335 0500~0835 0900~0915 #345~#360 #340 #400~#699
All Processors: External Page = #039
All processors except RCTUE/F: Night Ring Over External Page = #271
Night Ring Over External Page for RCTUE/F = #366
DNIS Number (2~5 digits)
Press LED Button 01 to blank out data.DNIS Address (see legend above)
Ringing Destination (see legend below)
Use LED Button 01 to blank out data.Enter 1, 2, or 3
1 = Day Ring Assignment
2 = Day2 Ring Assignment
3 = Night Ring Assignment
DNIS Address (see legend above)
For ANI-only lines, enter address (only one assignment is 
provided for ANI lines without DNIS, see legend above). 
						

							System & Station
Program 71 – DNIS
3-148Strata DK Programming 5/99
Program 71-4: DNIS and ANI Only Lines Voice Mail ID Assignments
Program 71-5: DNIS Number Name Display
DNIS Record Sheet




  6SNU   +ROG  6SNU  ‡‡‡ +ROG 6SNU+ROG 6SNU+ROG




  6SNU   +ROG  6SNU  ‡‡‡ +ROG 6SNU+ROG 6SNU+ROG
DNIS 
AddressDNIS Number
(1~5 digits) 
71-0DNIS Number
Routing Points (71-
1, 71-2, 71-3)DNIS Number
VM ID Code (1~16 digits)
71-4DNIS Number Name
(1~16 characters)
71-5
123
VM ID Code
Enter VM ID code that should be sent to Voice Mail 
when the selected DNIS number Call-Forwards or 
rings directly to Voice Mail (1~16 digits).
Press LED Button 02 to enter 

Press LED Button 03 to enter #
Press LED Button 04 to enter Pause
DNIS Address 
(see legend above)
Important!DNIS VM ID codes operate with in-
band DTMF tone VM integration only; 
not with SMDI VM integration.
DNIS NAME TAG (up to 16 characters)
Use the character entry procedures that follow 
Program 93 record sheets. NAME TAG displays on 
LCD telephones when a DNIS Call rings in.DNIS Address
 (see previous legend) 
						

							System & Station
Program 71 – DNIS
Strata DK Programming 5/993-149
System & Station
Program 71-0 Overview
Defines the DID / Tie / DNIS / ANI line extension numbers that the system should be able to 
receive. Each extension number can be from two to five digits; normally the local telephone 
company and/or the DNIS long distance carrier company will provide a list of these numbers.
Each RCTU supports a different quantity of DNIS or DID/Tie line extension numbers (shown 
above in the Program Sequence).
To assign a DNIS and/or normal Tie/DID line to Program 70-0 assignments: Program 17, LED 05 
must be turned ON for the line. In this case, Tie lines do not follow Program 04 assignments and 
DID lines do not follow Program 
09 assignments. When this program is used with normal (non-
DNIS or non-ANI) Tie and/or DID Lines -Program 17, LEDs 06, 07, and 08 must be OFF.
Program 71-1~71-3 Overview
Assigns the routing destination of each DNIS and/or normal Tie/DID line extension number and/or 
the routing destination of Automatic Number Identification (ANI) only lines. 
Important!Program 71-1 assigns DNIS numbers to route to selected [DN] buttons and makes 
them flash when the DNIS number is called. When assigning DNIS numbers to route 
to Directory Numbers ([PDNs], [SDNs], [PhDNs]) using program 71-1, Program 
*71, *72, and *73 must also be used to assign the telephones, on which the [DNs] 
appear, to ring. When assigning DNIS numbers to route to ACD and DH groups 
using Program 71, the telephones (and appropriate [PDN], [SDN], or [PhDN]) in 
these groups must also be assigned to ring in Program *71, *72, and *73.
DNIS 
AddressDNIS Number
(1~5 digits) 
71-0DNIS Number
Routing Points (71-
1, 71-2, 71-3)DNIS Number
VM ID Code (1~16 digits)
71-4DNIS Number Name
(1~16 characters)
71-5
123 
						

							System & Station
Program 71 – DNIS
3-150Strata DK Programming 5/99
A DNIS and/or Tie/DID extension number and/or ANI only line can be assigned to route one of 
the following destinations: 
©Primary Directory Number [PDN] - secondary appearances of this [PDN] will also ring if 
Programmed to ring in Program *71, *72, and/or *73
©Phantom Directory Number
©Distributed Hunt Group
©ACD Group
©Outside telephone number routed externally over the Public Telephone Network
©The system remote maintenance modem
©Night ringing over the external page
©The external voice paging system (Private Network Tie lines only)
A DNIS number or ANI only line can be assigned to route to one destination only in each of the 
three system ringing modes (Day, Day2 and Night); the destination can be unique or different in 
each ringing mode. For each DNIS Tie/DID extension number, the routing destination can be a 
unique destination or it can be the same destination as that assigned to other DNIS numbers. To 
assign lines that receive both ANI and DNIS with each call to Program 71-1 assignments: Program 
17, LED 05, 07 and 08 must be turned ON; for lines that receive DNIS digits only, LED 05 and 08 
must be ON.
This program can also be used with non-DNIS or non-ANI Tie and/or DID lines to route calls. In 
this case, the normal Tie digit assignments in Program 04 and DID digit assignments in Program 

09 will not be active - Program 17, LED 06, 07, 08 must be OFF and LED 05 must be ON for 
normal Tie/DID lines. 
The last address (499 for RCTUC3/D3, RCTUE3/F3; 349 for RCTUBA3/B3; and 199 for 
RCTUA3 or DK40i) in Program 71-0 is used to assign ANI only lines to a routing destination. All 
ANI only lines must be assigned to the same routing destination; this destination can be unique in 
each of the ringing modes (Day/Day2/Night).
To assign an ANI only Tie/DID line to Program 71-1 assignments: Program 17, LED 05 must be 
turned OFF and LED 07 and 08 must be ON for lines that receive ANI digits only.
Program 71-4 Overview
This feature is available when using DTMF In-band VM integration only; it is not provided with 
SMDI VM integration.
This Program assigns a Voice Mailbox ID (VMID) number to each DNIS/Tie/DID extension 
number and/or ANI only lines. This allows each DNIS/Tie/DID extension number and/or ANI 
only lines to be routed to a unique Voice Mail box when the number directly rings or is Call 
Forwarded to the Voice Mail system. When a DNIS/Tie/DID extension number or ANI line rings a 
station that has call forwarding set to Voice Mail, the DNIS/Tie/DID extension or ANI VMID is 
sent to the VM machine (if programmed in Program 71-4). If a DNIS/Tie/DID extension or ANI 
VMID is not programmed, the Call Forwarding station’s VMID is sent to the voice mail machine 
when the DNIS/Tie/ DNIS extension or ANI call forwards to VM. This program can also be used 
with non-DNIS Tie and/or DID lines to assign VMID digits to normal Tie or DID numbers.
The last address (499 for RCTUC3/D3, RCTUE3/F3; 349 for RCTUBA3/B3, and 199 for 
RCTUA3 or DK40i) in Program 71-4 can be used to assign a VMID code to ANI only lines. All 
ANI only lines will be directed to the same Voice Mailbox.
To assign an ANI only Tie/DID line to Program 71-4 assignments: Program 17, LED 05 must be 
turned OFF and LED 07 and 08 must be ON for lines that receive ANI digits only.  
						

							System & Station
Program 71 – DNIS
Strata DK Programming 5/993-151
System & Station
Program 71-5 Overview
This program is used to assign names to each DNIS number. The names for each DNIS/Tie/DID 
extension number is normally supplied by the customer. Each DNIS name can be up to 16 
alphanumeric characters. The DNIS/Tie/DID extension name will display on a telephone’s LCD 
when the DNIS/Tie/DID extension number rings the telephone directly or is transferred, Call 
Forwarded, or Hunted to the telephone. 
To assign a Tie/DID line to Program 71-5 assignments: Program 17, LED 05 must be turned ON 
for lines that should display DNIS/Tie/DID extension name tags. When a Tie/DID line receives 
both DNIS and ANI digits on the same call, Program 17, LED 06 determines what information, 
DNIS extension name or ANI number, will display as a priority when the line rings incoming to 
the system.
This program can also be used with non-DNIS or ANI Tie and/or DID lines to display names, 
associated with the Tie or DID numbers, on telephone LCDs. In this case, the normal Tie digit 
assignments in Program 04 and/or DID digit assignments in Program 
09 will not be active.
Important!
lAn individual telephone user can disable/enable the DNIS name display by using the Mode 60/
61 function on his/her LCD telephone. 
lThe DNIS extension name can be assigned or not assigned to display as a priority over the 
ANI display (in Program 17, LED06) when both ANI and DNIS digits are received on the same 
call.
lIf a name is not assigned to a DNIS number, DN:XXXX will display on telephone LCDs when 
the DNIS/Tie/DID line rings into the DK system (where XXXX = actual DNIS/Tie/DID digits 
received). 
						

							System & Station
Program *71~*73 – [DN] to [DN], Tie to [DN], and DID to [DN] Ringing Assignments
3-152Strata DK Programming 5/99
Program *71~*73 – [DN] to [DN], Tie to [DN], and DID to 
[DN] Ringing Assignments
Processor Type:DK14, DK40i, All RCTUs
Program Type:System
Initialized Default:[PDNs] are programmed to immediately ring their 
respective telephones in Program *71; no other default ringing assignments are made.
Important!In the EK Telephone Ports column, enter the Program 04 telephone ports of the 
telephones that should ring when the [DN] is called from another [DN] or a Tie or 
DID line (maximum of 120 telephones can be assigned to ring). The [DN] button 
must be assigned (Program 39) to the telephone that should ring.




  6SNU
 +ROG  6SNU  (.%XWWRQ +ROG 6SNU+ROG
Processor[PDN] Port[PhDN] PortProcessor[PDN] Port[PhDN] Port
DK14 000~009 500~509 RCTUBA/BB 000~079 500~589
DK40i 000~027 500~527 RCTUC/D 000~239 500~739
RCTUA 000~031 500~531 RCTUE/F 000~335 500~835
[DN] Port Reference 
NumberEK Telephone Ports (The Program 04 [PDN] port number of the telephones that should ring.)
Press the button associated with the 
telephones (EKs) that should ring 
when the selected [DN] is called.
Port Reference Number of that should ring [PDN] or [PhDN]
Press 
6FUROO to advance or 3DJH to go back.
Press Vols to turn all LEDs ON.
Press Volt to turn all LEDs OFF. Enter:
1 = Immediate Ring
2 = Delay 1 Ring (12 sec. delay)
3 = Delay 2 Ring (24 sec. delay)
To add a port range, enter 
XXX
XXX (low port 
 high port). 
						

							System & Station
Program *71~*73 – [DN] to [DN], Tie to [DN], and DID to [DN] Ringing Assignments
Strata DK Programming 5/993-153
System & Station
First Telephone Group
Buttons 01~20 on the programming telephone are associated with the telephone groups displayed 
on the telephone LCD.
GRP EK000 = Telephone Port 000 is represented by programming button 01...
GRP EK001 = Telephone Port 001 is represented by programming button 02...
GRP EK019 = Telephone Port 019 is represented by programming button 20.
Second Telephone Group
In telephone group “GRP 020~039”, the relationship is as shown below:
GRP EK020 = Telephone Port 020 is represented by programming button 01...
GRP EK021 = Telephone Port 021 is represented by programming button 02...
GRP EK039 = Telephone Port 039 is represented by programming button 20.
Program *71, *72, *73 Overview
Primary/Phantom Directory Number and Telephone Ringing assignments:
©This program assigns telephones to ring when a [PDN] or [PhDN] that appears on the 
telephone is dialed from another telephone (direct or transferred call). The [PDN] may appear 
as an [SDN] on other telephones that should ring.
©This program assigns telephones to ring when a call is routed from a Tie, DID, DNIS, DNIS/
ANI or ANI only line to a [PDN] or [PhDN] that appears on the telephone. The [PDN] may 
appear as an [SDN] on other telephones that should ring.
©Calls that Call Fwd, Hunt, or are transferred to a [PDN] or [PhDN] will ring on telephones per 
Program *71, *72, and *73 ringing assignments. The [PDN] or [PhDN] must appear on a 
flexible button (as a [PDN], [SDN], or [PhDN]) of telephones that should ring.
Important!120 Telephones (maximum) can be programmed to ring for any given [PDN], 
[SDN] or [PhDN] in Program *71, *72, and *73 combined.
For the above case: 
©Telephones can be programmed to immediately Ring (*71 assignments), delay ring after 12 
seconds (*72 assignments), or delay ring after 24 seconds (*73 assignments) for each [PDN] 
or [PhDN] button that appears on the telephone.
©The called [PDN], [SDN], or [PhDN] button must be programmed to appear (Program 39) on 
all Telephones that should ring. 
						

							System & Station
Program 72 – DNIS Number Network Table Assignments
3-154Strata DK Programming 5/99
Program 72 – DNIS Number Network Table 
Assignments
Processor Type:DK40i, All RCTUs
Program Type:System
Initialized Default:Blank




  6SNU   +ROG  6SNU ‡‡‡ +ROG 6SNU+ROG 6SNU+ROG
Route to PortsNetwork Table 
NumberTotal DNIS Network 
NumberRoute to PortsNetwork Table 
NumberTotal DNIS Network 
Number
DK14 NA NA RCTUBA/BB 300~499 200
DK40i 300~399 100 RCTUC/D 300~599 300
RCTUA 300~399 100 RCTUE/F 400~699 300
Network 
Ta b l e  
NumberGround / Loop / Tie / DID Line Access Code and 
Network Telephone NumberNetwork 
Ta b l e  
NumberGround / Loop / Tie / DID Line Access Code and 
Network Telephone Number
Line Access Code and Network Telephone 
Number (1~27 digits)
Any type line can be accessed (ground, loop, 
Tie, and/or DID) to send a DNIS call back out 
over the telephone network.
Press LED Button 02 to enter 

.
Press LED Button 03 to enter #.
Network Table Number