Toshiba Strata Xiie, Strata Xxe Electronic Key Telephone Systems Installation And Maintenance Manual

							PROGRAMMING PROCEDURES 
SECTION 300-020-300 
JULY 1966 
TABLE 39 
PROGRAM 5XX 
STATION CLASS OF SERVICE #l 
1) Lock in the SET switch on the HCAU. 
SPKR LED flashes continuously. 
INT and CO LEDs go on according to present 
s on or 0 If the LED is already on, depressing its asso- 
ciated key will turn it off and vice versa. LEDs 
may be turned off and on until the desired pat- 
with this program 
or . . . 
6B) Go to Step 2 in another program table 
. . . or . e . 
6C) Transfer data into working memory per 
Paragraph 02.06. SET LED goes off. 
Station 17 MW/FL LED goes off. 
New data is stored, previous data is erased. 
-61-  
						

							PROGRAMMING PROCEDURES 
SECTION 300-020-300 
JULY 1986 
TABLE 40 
PROGRAM 5#XX 
STATION CLASS OF SERVICE #2 
1) Lock in the SET switch on the HCAU. W/FL LED on. 
em IS In program mode. 
grammed.) 
NOTE: INT and CO LEDs go on according to present 
For multiple station programming, refer to 
keys, turn their associate 
LED is already on, depressing its asso- 
ed off and on until the desired pat- 
6B) Go to Step 2 in gG;h& program table 
. . . or s . ~ 
6C) Transfer data into working memory per 
-62-  
						

							PROGRAMMING PROCEDURES 
SECTION 300-020-300 
JULY1986 
TABLE 41 
PROGRAM 6XX 
STATION TOLL RESTRICTION CLASSIFICATION 
1). Lock in SET switch on the HCAU. 
SPKR LED flashes continuously. 
tation programming, refer to Para- INT, CO LEDs go on according to present data. 
the System Record Sheet. Using the An X on the record sheet means the LED should 
off, as required. If the LED is already on, depressing its asso- 
rned off and on until the desired pat- 
All station 17 LEDs (except MW/FL) go off. 
this program 
6B). Go to Step 2 in’an%er*program table 
. . . or . . . 
into working memory per 
*See Toll Restriction; Programs 100, 1 Xl, 1 XY, 1 X2 and 2XY. 
-63-  
						

							PROGRAMMING PFjOCEOURES 
SECTION 300-020-300 
JULY 1986 
TABLE 42 
PROGRAM 6#XX 
STATION-TO-STATION HUNTING 
1) Lock in the SET switch on the HCAU. Station 17 MW/FL LED on. 
ram defines the station hunt destination. This LEDs as shown below. 
with this program 
6B) Go to Step 2 in gonb%x program table 
. . . or . . . 
6C) Transfer data into working memory per 
Paragraph 02.06. SET LED goes off. 
Station 17 MW/FL LED goes off. 
-64-  
						

							PRUGRAMMING PROCEDURES 
SECTION 300-020-300 
JULY 1988 
TABLE 43 
PROGRAM 7XX 
STATION OUTGOING CALL RESTRICTION 
1) Lock in the SET switch on the HCAU. Station 17 MW/FL LED on. 
as requrred. 
0 LED on = Restricted outgoing calls. 
0 Each CO key/LED represents itself-that is, 
if the CO1 .LED is on, then the station being e LED is already on, depressing its asso- 
ciated key will turn it off and vice versa. LEDs 
may be turned off and on until the desired pat- 
66) Go to Step 2 in another program table 
or . . .  . . 0 
66) Transfer data into working memory per 
Paragraph 02.06. SET LED goes off. 
Station 17 MW/FL LED goes off. 
New data is stored, previous data is erased. 
-65  
						

							PROGRAMMING PROCEDURES 
SECTION 300-020-300 
JULY 1986 
TABLE 44 
PROGRAM 8XX 
CO RINGING ASSIGNMENTS-DAY 
1) Lock in the SET switch on the HCAU. W/FL LED on. 
ystem IS In program mode. 
grammed.) 
NOTE: e station to be pro- 
CO LEDs indicate present data. 
For multiple station programming, refer to 
2) A maximum of eight stations may be assigned to ring for any given CO /inc. If more are assigned, 
as required. 
0 LED on = Restricted outgoing calls. 
0 Each CO key/LED represents itself-that is, 
if the CO1 LED is on, then the station being If the LED is already on, depressing its asso- 
ciated key will turn it off and vice versa. LEDs 
this program 
6B) Go to Step 2 in a~~ther program table 
or . . .  . . . 
6C) Transfer data into working memory per 
Paragraph 02.06. SET LED goes off. 
Station 17 MW/FL LED goes off. 
New data is stored, previous data is erased. 
-66-  
						

							PROGRAMMING PROCEDURES 
SECTION .300-020-300 
JULY 1986 
TABLE 45 
PROGRAM 8#XX 
CO RINGING ASSIGNMENTS-DAY 2 
W/FL LED on. 
I) Lock in the SET switch on the HCAU. 
ystem IS In program mode. 
NOTE: CO LEDs indicate present data. 
For multiple station programming, refer to 
2) A maximum of eight stations may be assigned to ring for any given CO line. if more are assigned, 
as required. 
0 LED on = Ring in DAY 2 mode. 
@ Each CO key/LED represents itself-that is, 
if the CO1 LED is on, then the station being 
(XX) will ring for CO1 in the the 
LED is already on, depressing its asso- 
ciated key will turn it off and vice versa. LEDs 
may be turned off and on until the desired pat- 
or . . . 
63) Go to Step 2 in another program table 
or . . .  . . . 
6C) Transfer data into working memory per SET LED goes off. 
Station 17 MW/FL LED goes off. 
New data is stored, previous data is erased. 
NOTE: 
This program is used only if the CO8 LED was turned on in Program 03. 
-67-  
						

							PROGRAMMING PROCEDURES 
SECTION 300-020-300 
JULY 1986 
TABLE 46 
PROGRAM SXX 
CO RINGING ASSIGNMENTS-NITE 
SET LED on. 
1) Lock in the 
SET switch on the HCAU. Station 17 MW/FL LED on. 
System is in program mode. 
2) Depress the m key on station 17. 
3) Dial Ei) 1 Bon the dial pad. 
(XX = the number of the station to be pro- 
grammed.) 
NO TE. Normal functions halt on station 17. 
SPKR LED steady on. 
SPKR LED flashes continuously. 
CO LEDs indicate present data. 
For multiple station programming, refer to 
Paragraph 02.20. 
NOTES: 
1) Any station(s) designated to ring on a CO line must be allowedaccess to that line via 
Program 3xX 
2) A maximum of eight stations may be assigned to ring for any given CO line. If more are assigned 
the lowest eight station numbers will ring-the others will be ignored. 
, turn the associated LEDs on or off, 
If the LED is already on, depressing its asso- 
Ring in NITE mode. ciated key will turn it off and vice versa. LEDs 
l Each CO key/LED represents itself-that is, may be turned off and on until the desired pat- 
LED is on, then the station being 
ed (XX) will ring for CO1 in the 
this program 
. . ~ or . ~ . 
6B) Go to Step 2 in another program table 
. . . or . . . 
into working memory per SET LED goes off. 
Station 17 MW/FL LED goes off. 
-68-  
						

							TOSHIBA SYSTEM PRACTICES 
ELECTRONIC KEY TELEPHONE SYSTEM Strata XII, & XX, 
SYSTEM RECORD 
JULY 1986 
Strata@ X/I, & XX= 
SYSTEM RECORD 
APPENDIX 1 
TSD 86-06-06