ViewSonic Pjd5353 Projector User Manual

 EN-18
Connecting a Component Video source device
Examine your Video source device to determine if it has a set of unused Component 
Video output sockets available:
„If so, you can continue with this procedure.
„If not, you will need to reassess which method you can use to connect to the 
device.
To connect the projector to a Component Video source device:
1. Take a VGA (D-Sub) to HDTV (RCA) cable and connect the end with 3 RCA type 
connectors to the Component Video output sockets of the Video source...

EN-19
Connecting a composite Video source device
Examine your Video source device to determine if it has a set of unused composite 
Video output sockets available:
„If so, you can continue with this procedure.
„If not, you will need to reassess which method you can use to connect to the 
device.
To connect the projector to a composite Video source device:
1. Take a Video cable and connect one end to the composite Video output socket of 
the!Video source device.
2. Connect the other end of the Video cable...

 EN-20
Operation
Powering On/Off the Projector
Powering On the Projector:
1. Complete the AC power cord and peripheral signal cable(s) connections.
2. Press   to turn on the projector.
The projector takes a minute or so to warm up. 
3. Turn on your source (computer, notebook, DVD, etc.). The projector 
automatically detects your source.
„If you are connecting multiple sources to the projector simultaneously, press 
SOURCE on the projector or Source on the remote control to select your 
desired signal or...

EN-21
Adjusting the Projector Height
The projector is equipped with an elevator foot to adjust the image height. To raise or 
lower the image, turn the elevator foot to fine-tune the height.
Adjusting the Projector Focus
Focus the image by rotating the focus ring. A still image is recommended for focusing.
Elevator foot
„To avoid damaging the projector, make sure that the elevator foot is fully 
retracted before placing the projector in its carrying case.
Focus ring
21 

 EN-22
Adjusting Projection Image Size
Refer to the graphic and table below to determine the screen size and projection distance.
Screen size 
Diagonal
[inch (cm)]4 : 3 Screen
Projection 
distance [inch (m)]Image height 
[inch (cm)]Image width 
[inch (cm)]Vertical offset
 [inch (cm)]
40 (102) 22 (0.5) 24 (61) 32 (81) 3.6 (9)
60 (152) 33 (0.8) 36 (91) 48 (122) 5.4 (14)
80 (203) 44 (1.1) 48 (122) 64 (163) 7.2 (18)
100 (254) 55 (1.4) 60 (152) 80 (203) 9.0 (23)
150 (381) 83 (2.1) 90 (229) 120 (305) 13.4...

EN-23
Locking control keys
With the control keys on the projector locked, you can prevent your projector settings 
from being changed accidentally (by children, for example). When the Panel Key 
Lock is on, no control keys on the projector will operate except   Power.
1. Press  on the remote control.
2. A confirmation message is displayed. Select Ye s to 
confirm.
To release panel key lock:
1. Press  on the remote control.
2. A confirmation message is displayed. Select Ye s to 
confirm.
Important
„If you...

 EN-24
Setting the presentation timer
The presentation timer can indicate the presentation time on the screen to help you 
achieve better time management when giving presentations. Follow these steps to 
utilize this function:
1. Go to the Option > Presentation Timer menu and press  on the projector or 
Enter on the remote control to display the Presentation Timer page.
2. Highlight Timer Period and decide the timer period by pressing  / .
Important
„If the timer is already on, the timer will restart...

EN-25
Menu Operation
The projector has multilingual on-screen display menus that allow you to make image 
adjustments and change a variety of settings.
25 

 EN-26
26 

EN-27
How to operate
1. Press MENU on the projector or Menu on the remote control to open the OSD
menu.
2. When OSD is displayed, use  /  to select any feature in the main menu.
3. After selecting the desired main menu item, press   to enter sub-menu for
feature setting.
4. Use  /  to select the desired item and adjust the settings with  / .
5. Press MENU on the projector or Menu on the remote control, the screen will
return to the main menu.
6. To exit OSD, Press MENU on the projector or Menu on the...