Vivitar Projector H9090 User Manual

11
KEYPAD
• MENU 
Press this button to show or hide the OSD menu.
•  SELECT ▲▼◄►
Use these buttons to select items or settings, adjust settings or switch\
 display patterns.
•  SOURCE 
Press to select a video source. HDMI1, HDMI2, RGB, COMP1, COMP2, VIDEO o\
r 
S-VIDEO.
•  Power 
Use the button to turn on/off the projector.
•  LED STATUS 
The LED status indicators are for different colors or blinking of the lights mean.
LED Indicator
Blue (Power) Red (Issue)
Standby
Cooling / Warm up
Power on / Normal...

12
REMOTE CONTROL
	Status LED Power Bottons:
Use these button to turn the projector on(l) or off
().
	Source Selection Buttons (1-5):
Press to select a video source. By default, these buttons are        
  signed as follows: 
1 = HDMI 1; 2 = HDMI 2; 3 = Component 1; 
4 = S-Video; 5 = Video.
However, you can assign each button to any source you wish.
	Cursor Keys (▲▼◄►) 
Use these buttons to select items or settings, adjust 
settings or switch display patterns.
ENTER
Press to select a highlighted menu...

13
INTALLATION
To install batteries in the remote
1. Slide the battery compartment cover in the direction of the arrow to rem\
ove it.
2.  Install two AA batteries with the correct polarity.
3.  Replace the cover.
123
Note on Batteries 
•	Make sure that the battery polarities are correct when installing the ba\
tteries
•	 Do not mix an old battery with a new one or different types of batteries\
.
•	 If you will not use the remote control for a long time, remove the batte\
ries to avoid     
damage from...

14
Installation Considerations
Proper installation of your projector will ensure the quality of your di\
splay. Whether you are 
installing a projector temporarily or permanently, you should take the following into account 
to ensure your projector performs optimally. 
Ambient Light 
In general, minimize or eliminate light sources directed at the screen. \
Contrast ratio in your 
images will be noticeably reduced if light directly strikes the screen, \
such as when a shaft 
of light from a window or...

15
Modes of installation
 
■ Frontal projection - desktop installation 
Advantages: easy to install can be easily moved 
or adjusted easy to operate .
Disadvantage: occupies floor space and limits 
seating capacity. 
Projector
 
■ Rear projection - desktop installation
Advantage: The projector is completely hidden   
from plain view the projector can be easily 
operated this setup usually offers better reduction 
of ambient noise. 
Disadvantage: requires an additional room for 
installation relatively...

16
Allow at least 50 cm clearance around the exhaust vent
50cm above
30cmabove50cm above50cm above
10cm above
Do not tilt the projector more than 15 degrees
The maximum tilt angle for the projector is 15 degrees. 
When the projector is tilted more than 15 degrees, it will shorten the l\
ife of the projector 
lamp and may lead to other unpredictable damages.
Can’t > 15
Can’t > 15
Other Considerations
• Install the projector in an environment below 35°C (95°F). The projector should be kept   
  clear from...

17
Lens Shift
Vertical Lens Shift
The H9090 has a lens shift capability which allows the vertical movement\
 of the image 
without moving the projector. Lens shift is generally expressed as a percentage of the 
screen height. For ceiling mounted projectors, the lens can be moved 120\
% (0.6V) 
downward, while the lens can be moved 120% (0.6V) up or down on a desk\
top mounted 
projector.
V
0.6V
0.6V
0.6V
V
Horizontal Lens Shift
The H9090 has a lens shift capability which allows the horizontal moveme\
nt...

18
Connecting the projector to other devices
HDMI Connection
Proceed as follows to connect the H9090 to your video sources, external \
controller(s) - if 
present - and AC power. When connecting your equipment: •Use the correct signal cables 
for each source. •Ensure that the cables are securely connected. Tighten the thumbscrews 
on connectors that have them. Connecting Source Components to the H9090 \
Connect 
your video sources to the H9090 as shown and described in the sections t\
hat follow .
12V...

19
IR Input connection
If infrared signals from the remote control cannot reach the projector d\
ue to excessive 
distance or obstructions such as walls or cabinet doors, you can connect\
 an external IR 
repeater system to the IR INPUT on the H9090 to extend the range of the remote control.
Remote
IR sensor
IR repeater
S-VIDEO, VIDEO connection
If the image input device offers both S-Video and Video connection, it is recommended that 
you choose S-Video to obtain better image quality. If both the...

20
COMPONENT connection
Connect your component video sources to the COMPONENT 1, COMPONENT 2 or RGB 
inputs as shown.
DTV set-top-box or other
component (YPbPr) input source
YPbPr
RS-232 Controller Connection
Connect a PC or home theater control/automation system (if present) to\
 the RS-232 port 
on the H9090. Use a standard, 9-pin serial cable, wired straight-through\
.
H9090 Home Theater Projector - User Manual