Vivitar Projector H9090 User Manual

21
Start using the projector – Adjustments
Connecting to AC Power
Use the supplied AC power cords. Plug the female end of the power cord into the AC 
receptacle on the rear of the projector (AC 100V ~ 240V); Then, connect the other end to 
your AC power source.
Turning on the Power
Press the ON button on Remote controller or the Power button from the pr\
ojector’s keypad. 
The power LED indicator flashes green to indicate that it is warming up. When the projector 
is ready for use, the LED indicator...

22
Changing the OSD Language
Press MENU to display the OSD, Press ◄►to select LANGUAGE item, then press  ◄►to 
select a language that you wanted. Then press ENTER to confirm your selection.
MAINSER VICELANGUAGECONTROLSYSTEMADVANCED
Menu = Exit Menu Select   Scroll  
English
Français
Español
Adjusting the Picture Orientation
The H9090 will automatically inverts the image from Floor Front to Ceili\
ng Front if the 
projector is mounted on the ceiling. If this automatic inversion is not \
de-sired, please...

23
Mechanical Adjustments
The H9090 gives you a great deal of control over the picture size, posit\
ion and focus. 
Focus To focus the projected image, grasp the lens by the front ring and rotate\
 it.
Focus ring
H/V Shift adjustment
Front Infre-red
window
(remote control)Adjustablefeet*4
Zoom ringAir inlet
Adjust foot
Rotate the 4 feet on projector for image 
position. 
Note: Ceiling Mode can’t adjust this function.
Vertical and Horizontal Lens Shift 
To shift the projected image 
1. 
lift the logo...

24
Operation
Selecting an Input Source
H9090 will remember the last selected input source.Use these buttons on the remote control to 
select an input source directly. The default 
assignments are: 1 = HDMI 1, 2 = HDMI 2, 
3 = Component 1, 4 = S-Video, 5 = Video.  
You can assign each of these five buttons to 
any input. 
For more information,  refer to Page 36 --- 
1 Key / 2 Key / 3 Key / 4 Key / 5 Key
Selecting an Aspect Ratio
Press the aspect ratio button to select the 
appropriate aspect ratio for the...

25
Using the On-Screen Menus (OSD)
1. Press the MENU button on the remote control or system keypad to display \
the Main 
Menu.
2.  There are six menus. Press  ◄ or  ► to select a sub-menu.
3.  Press  ▲ or  ▼ to select a sub-menu item. 
4.  For each sub-menu item, the currently-selected value is highlighted. Pre\
ss  ▲ or  ▼ to  
  choose a setting for that item, and press ENTER on the remote controller\
 or SELECT  
  on the keypad to adjust the value of that item. 
5.  Press MENU to return to the...

26
Start using the projector - OSD Introduction
OSD Menu Tree
The H9090 menus are arranged hierarchically, as shown from below. Depending on the 
selected input source and signal characteristics, some menu options may \
not be available.
MAINAspect Ratio 
16:9, Letterbox 4:3, 4:3 
Narrow, Native
Presets Recall Presets
Save Presets
Brightness
0....100...200
Contrast
Saturation
Hue
Sharpness
Noise Reduction
Overscan
Off, Crop, Zoom
Input Select HDMI1, HDMI2, RGB, 
Comp1 Comp2, 
Video, S-Video
Resync (press...

27
OSD Introduction – MAIN
MAINSERVICELANGUAGECONTROLSYSTEMADVANCED
Menu = Exit Menu Select   Scroll  
Aspect Ratio
Presets
Brightness
Contrast
Saturation
Hue
Sharpness
Noise Reduction
Overscan
Input Select
Resync
16:9 
Letterbox  4:3 4:3 Narrow  Native
Enter 100
100
100
100
100
100
Of f  Crop  Zoom
Enter
Enter
Aspect Ratio:  To change the aspect ratio (size and shape) of the projected image, pre\
ss 
▲  or ▼ to highlight Aspect Ratio. Use the  ◄ or  ► buttons to select the appropriate aspect 
ratio for...

28
Preset: Select Presets from the Main menu, then press ENTER to recall image qual\
ity    
         settings previously saved, or to save changed settings in any of fo\
ur memory    
         locations.
•  Recall Presets: Select Recall Presets from the Memory menu to recall saved image   
  quality settings. Unless you select Default (see below), this control \
affects all sources,  
  not just the active source.
•  Custom Memory A, Custom Memory B, Custom Memory C, Custom Memory D,    
  contain the...

29
Brightness: On your external test pattern source, select a PLUGE pattern. (PLUGE i\
s an 
acronym for “Picture Line-Up Generation Equipment.”) 
          Typical PLUGE Pattern for Adjusting Brightness
PLUGE patterns vary but generally consist of some combination of black, \
white and gray 
areas against a background. The example above includes two vertical bars and four 
shaded boxes.
Select Brightness from the Image menu. Use the  ◄► buttons to adjust the level so that:
The darkest black bars...

30
Saturation (Color): Available only for Standard Definition (SD) signals (480i, 576i) in 
Video, S-Video, and Component inputs.
To adjust the overall color intensity, select Color from the Main menu. Decrease this setting 
if colors are overly saturated; increase it if colors appear muted .
Hue (Tint):  Available only for Standard Definition (SD) signals (480i, 576i) in Video, S-Video, 
and Component inputs 
Hue “Tint” is the ratio of red to green in the color portion of the image. \
To adjust the...