Vivitek D7180hd User Manual

DLP Projector – User’s Manual 
 
 
Specsheet for “RS232 by TELNET” : 
1. Telnet: TCP 
2.  Telnet port: 8000 
3.  Telnet utility: Windows “T ELNET.exe” (console mode) 
4.  Disconnection for RS232-by-Telnet  control normally: Close Windows Telnet utility directly after 
TELNET connection ready 
5.  Limitation 1 for Telnet-Control: there is onl y one connection for Telnet-Control in one projector 
Limitation 2 for Telnet-Control: there is less  than 50 bytes for successive network payload for...

DLP Projector – User’s Manual 
 
 
SETUP>>Advanced Menu  
Press the MENU  button to open the  OSD menu. Press the cursor  ◄► button to move to the 
SETUP>>Advanced  menu. Press the cursor  ▲▼ button to move up and down in the     
SETUP>>Advanced  menu.  
 
ITEM DESCRIPTION 
Audio  Press the 
ENTER button to enter the  Audio sub menu. 
See  Audio  on page  34. 
Lamp Press  the ENTER  button to enter the  Lamp sub menu. See  Lamp on page  34. 
HDMI Press  the ENTER  button to enter the  HDMI sub menu. See...

DLP Projector – User’s Manual 
 
 
Audio 
Press the ENTER  button to enter the  Audio sub menu. 
 
ITEM DESCRIPTION 
Volume Press  the ◄►  buttons to adjust the audio Volume. 
Treble Press  the ◄►  buttons to adjust the audio Treble. 
Bass Press  the ◄►  buttons to adjust the audio Bass. 
Mute Press  the ◄►  buttons to turn on or off the speaker.  
AGC Press  the ◄►  buttons to turn on or off the AGC setting. 
Reset Press  the ENTER  button to reset all settings to default values. 
 
Lamp 
Press the...

DLP Projector – User’s Manual 
 
 
HDMI 
Press the ENTER  button to enter the  HDMI sub menu. 
 
ITEM DESCRIPTION 
HDMI Format  Press the 
◄► buttons to select from three HDMI display formats: 
Auto/ PC signal/ Video signal. 
HDMI Amplifier Gain  Press the ◄► buttons to adjust HDMI Amplifier Gain. 
 
Closed Caption 
Press the ENTER  button to enter the  Closed Caption sub menu. 
 
ITEM DESCRIPTION 
Closed Caption Enable  Press the ◄► buttons to turn on or off Closed Caption. 
Caption Version  Press the...

DLP Projector – User’s Manual 
 
 
Presentation Timer 
The Presentation Timer func tion can indicate the presentation ti me on the screen to help you achieve 
better time management when giving presentations. 
 
ITEM DESCRIPTION 
Timer  Press the cursor ◄► button to enable or disable presentation timer. 
Timer Period  Press the cursor ◄► button to select timer period (1 ~ 60 minutes) 
Timer Reset  Press  (Enter) / ► to reset the timer settings. 
 
—  36 —  

DLP Projector – User’s Manual 
 
 
STATUS Menu 
Press the  MENU button to open the  OSD menu. Press the cursor  ◄► button to move to the  
STATUS Menu .  
 
ITEM DESCRIPTION 
Source  Displays the activated input source. 
Resolution  Displays the native resolution of input source. 
Lamp Hour Displays the number of hours the lamp has been in use. 
Firmware Version  Displays the firmware version of the projector. 
Note:  
Status displayed in this menu is  for viewing only and cannot be edited. 
 
– 37  –  

DLP Projector – User’s Manual 
 
 
—  38 — 
MAINTENANCE AND SECURITY 
Replacing the Projection Lamp 
The projection lamp should be replaced when it burns out. It should only be r eplaced with a certified 
replacement part, which you can order from your local dealer.  
Important: 
a.  The projection lamp used in this product contains a small amount of mercury. 
b.  Do not dispose this product  with general household waste. 
c. Disposal of this product must be carried out in  accordance with the...

DLP Projector – User’s Manual 
 
 
2.  Remove the lamp compart-
ment cover. 
 
3. Remove the two screws from 
the lamp module. 
4. Lift the module handle up. 
5. Pull firmly on the module  
handle to remove the lamp 
module. 
 
6. Reverse steps 1 to 5 to install 
the new lamp module.  
While installing, align the 
lamp module with the  
connector and ensure it is level 
to avoid damage. 
Note: The lamp module must 
sit securely in place and the 
lamp connector must be con-
nected properly before...

DLP Projector – User’s Manual 
 
 
Cleaning the Projector 
Cleaning the projector to remove dust and grime will help ensure trouble-free operation.  
Warning: 
1.  Be sure to turn off and unplug the projector at  least 30 minutes before cleaning. Failure to do so 
could result in a severe burn. 
2. Use only a dampened cloth when cleaning. Do not allow water to enter the ventilation openings 
on the projector.  
3. If a little water gets into the projector interior  while cleaning, leave unplugged in a...

DLP Projector – User’s Manual 
 
 
–  41  – 
Cleaning the Lens 
You can purchase optic  lens cleaner from most camera stores . Refer to the following to clean the pro-
jector lens. 
1.   Apply a little optic lens cleaner to a clean soft cloth. (Do not apply the cleaner directly to the lens.) 
2.   Lightly wipe the lens in a circular motion. 
Caution: 
1. Do not use abrasive cleaners or solvents. 
2. To prevent discoloration  or fading, avoid getting cleaner on the projector case. 
Cleaning the Case...