Xerox 700 Digital Color Press User Manual

User Guide7-11
Xerox 700 Digital Color Press
Maintenance
Open the Drum Drawer. 
Remove the old drum cartridge by holding the finger rings 
provided at the both ends of the drum cartridge and 
gently lifting up.
 
Place the new drum cartridge in the machine following the 
guides with the side marked front facing the front.
 
7.
8.
9.
Downloaded From ManualsPrinter.com Manuals 

User Guide
7-12
Maintenance
Xerox 700 Di
gital Color Press
Immediately close the Drum Drawer to protect the other 
drums from light.
CAUTION: Remember to close the Drum Drawer - Do not 
expose drum cartridges to direct sunlight or strong light 
from indoor fluorescent  lighting. Do not touch or scratch 
the surface of the drum. Doing so may result in 
unsatisfactory printing.
  
Return the R1-R4 handle to the original position and close 
the front door.
Insert the used drum cartridge into an empty...

User Guide7-13
Xerox 700 Digital Color Press
Maintenance
Lay paper on the floor before removing the cartridge.  This 
will allow any excess toner to fall on the paper.  Hold the 
handle of the color indicated in the message, and gently 
pull it out.
This procedure shows you how to remove a used toner cartridge and replac\
e it with a new toner cartridge.  The machine 
will notify you when a new toner cartridge is needed, and when installat\
ion is to occur.  If you continue copying or 
printing without...

User Guide
7-14
Maintenance
Xerox 700 Di
gital Color Press
Close the Front Door. If the door will not close completely, 
make sure the cartridge is in the lock position and the 
toner cartridge is installed into the appropriate toner 
location. Remove the toner cartridge by holding the handle on the 
top of the cartridge while gently pulling it straight out. Be 
careful to not get toner on clothing.
 
Dispose the toner cartridge as normal office waste or 
recycle the cartridge.
Remove the new toner...

User Guide7-15
Xerox 700 Digital Color Press
Maintenance
Carefully pull out the Transfer Module.
  Make sure the machine has stopped running, and open the 
Front Door.
 
Grasp Handle #2  and turn it to the unlocked position.
Warning: To avoid burns wait at least 5-10 minutes after 
powering off the printer to allow the fuser to cool down, 
and observe warning labels inside.
1.
2.
3.
Downloaded From ManualsPrinter.com Manuals 

User Guide
7-16
Maintenance
Xerox 700 Di
gital Color Press
Grab and lift the Amber-Gold colored handle only, lift and 
pull up and out of the Transfer Module.
Dispose the fuser as normal office waste or recycle the 
fuser.
 
Remove the new fuser from its packaging.
  Pull out the Fuser Handle.
4.
5.
6.
7.
Downloaded From ManualsPrinter.com Manuals 

User Guide7-17
Xerox 700 Digital Color Press
Maintenance
Close the Transfer module. Insert the Fuser into the Transfer module while holding 
the Amber-Gold handle.
 
Turn Handle #2  to the locked position.
 
Close the Front Door of the printer.
That completes the procedure for replacing the Fuser.
 
This procedure shows you how to remove the used Charge 
Corotron and replace it with a new Charge Corotron. The 
machine will tell you when you need to order a new one 
and when to install it.  
Replacing...

User Guide
7-18
Maintenance
Xerox 700 Di
gital Color Press
Pull down the R1-R4 handle.
 
Raise the Release Handle.
 Make sure the machine has stopped, and open the Front 
door.
 
CAUTION:
Do not expose this item to direct sunlight or strong light from indoor f\
luorescent lighting. Image quality may 
deteriorate when these are exposed to light for more than two minutes.2.
3. 1.
Downloaded From ManualsPrinter.com Manuals 

User Guide7-19
Xerox 700 Digital Color Press
Maintenance
Open the packaging for the new Charge Corotron and 
gently place the new Charge Corotron on a flat surface 
near the machine.
Pull out the Drum Drawer.
Grasp both of the amber-gold colored casings on the old 
charge corotron and push towards the back of the 
machine.  You will hear a clicking noise indicating that it is 
being released. CAUTION:
Remember to minimize the amount of time that the drum cartridges are exp\
osed to light.  Exposure for...

User Guide
7-20
Maintenance
Xerox 700 Di
gital Color Press
Remove the old charge corotron by holding the amber-
gold colored casings provided at the both ends of the 
charge corotron and gently pulling straight up.
Gently lower the new charge corotron into the machine 
straight down, and not at an angle.
7.
8.
Downloaded From ManualsPrinter.com Manuals