Home > Xerox > Printer > Xerox Phaser 6350 DX User Manual

Xerox Phaser 6350 DX User Manual

    Download as PDF Print this page Share this page

    Have a look at the manual Xerox Phaser 6350 DX User Manual online for free. It’s possible to download the document as PDF or print. UserManuals.tech offer 228 Xerox manuals and user’s guides for free. Share the user manual or guide on Facebook, Twitter or Google+.

    							Printing on Specialty Media
    Phaser® 6300/6350 Color Laser Printer
    3-34 6.Insert the tray into the tray slot, and push the tray completely into the printer.
    7.On the control panel, select the paper type:
    a.Select Change setup, and then press the OK button.
    b.Select Labels, and then press the OK button. 
    8.In the printer driver, select either Labels as the paper type or the appropriate tray as the 
    paper source.
    Printing Glossy Paper
    Glossy paper can be printed from any tray. It can be printed on both sides.
    To order paper, transparencies, or other specialty media, contact your local reseller or go to 
    www.xerox.com/office/supplies
    .
    Glossy Paper Guidelines
    ■Do not open sealed packages of glossy paper until you are ready to load them into the 
    printer.
    ■Leave glossy paper in the original wrapper, and leave the packages in the shipping carton 
    until ready to use.
    ■Remove all other paper from the tray before loading glossy paper.
    ■Load only the amount of glossy paper you are planning to use. Do not leave glossy paper 
    in the tray when you are finished printing. Reinsert unused glossy paper in the original 
    wrapper and seal. 
    ■Rotate stock frequently. Long periods of storage in extreme conditions can cause glossy 
    paper to curl and jam the printer.
    6300-036
    Downloaded From ManualsPrinter.com Manuals 
    						
    							Printing on Specialty Media
    Phaser® 6300/6350 Color Laser Printer
    3-35
    Printing Glossy Paper from Tray 1 (MPT)
    1.Open Tray 1 (MPT) by pulling out on the handle. 
    2.Pull out the tray extension, and open the paper guides.
    3.Fan the glossy paper to release sheets that are stuck together.
     
    6300-006
    6300-007
    Downloaded From ManualsPrinter.com Manuals 
    						
    							Printing on Specialty Media
    Phaser® 6300/6350 Color Laser Printer
    3-36 4.Insert the glossy paper into Tray 1 (MPT), and adjust the paper guides to fit the paper.
    ■Place the side to be printed facedown.
    ■Do not load more than 25 sheets.
    5.On the control panel, select the glossy paper type and size:
    a.Select Change setup, and then press the OK button.
    b.Select Glossy Paper, and then press the OK button. 
    c.Select the paper size, and then press the OK button.
    6.In the printer driver, select either Glossy Paper as the paper type or Tray 1 (MPT) as the 
    paper source.
    Printing Glossy Paper from Trays 2–5
    1.Pull the tray out of the printer.
    6300-008
    MAX
    6300-035
    Downloaded From ManualsPrinter.com Manuals 
    						
    							Printing on Specialty Media
    Phaser® 6300/6350 Color Laser Printer
    3-37 2.If necessary, open the paper guides:
    ■Squeeze the green tab on the length guide, and then slide it back. The guide clicks into 
    place.
    ■Slide the green side guides outward.
    3.Fan the paper to release sheets that are stuck together.
    6300-001
    Downloaded From ManualsPrinter.com Manuals 
    						
    							Printing on Specialty Media
    Phaser® 6300/6350 Color Laser Printer
    3-38 4.Insert the paper into the tray. 
    Note:Do not load the paper above the fill line indicated on the tray. Overloading the tray 
    may cause jams. In the following illustration, 2 indicates the maximum fill line for 
    transparencies, labels, glossy paper, and thin card stock.
    5.If necessary, press the paper guides inward to fit the paper.
    6.Insert the tray into the tray slot, and push the tray completely into the printer.
    6300-003
    MAX
    MAX
    1
    2
    6300-105
    6300-036
    Downloaded From ManualsPrinter.com Manuals 
    						
    							Printing on Specialty Media
    Phaser® 6300/6350 Color Laser Printer
    3-39 7.On the control panel, select the glossy paper type:
    a.Select Change setup, and then press the OK button.
    b.Select Glossy Paper, and then press the OK button. 
    8.In the printer driver, select either Glossy Paper as the paper type or the appropriate tray as 
    the paper source.
    Printing Custom Size Paper
    In addition to the wide variety of standard paper sizes that you can use for printing, you can 
    also print on custom size paper within the following dimensions.
    Printing Custom Size Paper from Tray 1 (MPT)
    1.Open Tray 1 (MPT) by pulling out on the handle.
    Tray 1 (MPT)
    Width: 89 – 216 mm (3.5 – 8.5 in.)
    Height: 140 – 900 mm (5.5 – 35.45 in.)
    6300-006
    Downloaded From ManualsPrinter.com Manuals 
    						
    							Printing on Specialty Media
    Phaser® 6300/6350 Color Laser Printer
    3-40 2.Pull out the tray extension, and open the paper guides.
    3.Insert the paper into Tray 1 (MPT), and adjust the paper guides to fit the paper. 
    ■The paper can be loaded with either the long or short edge entering first, as shown in 
    the illustrations. 
    ■The maximum width (X) is 212.5 mm (8.5 in.).
    ■For single-sided printing, if you are using preprinted or prepunched paper, place the 
    side to be printed facedown with the top of the paper entering the printer first.
    ■For 2-sided printing, if you are using preprinted or prepunched paper, place the first 
    side to be printed faceup with the bottom of the page entering the printer first.
    4.On the control panel, select Change setup, and then press the OK button.
    5.Select the paper type, and then press the OK button. 
    6.Do one of the following:
    ■If your custom paper size is listed in the menu, select it, and then press the OK button.
    ■If your custom paper size is not listed in the menu, select New Custom Size, and 
    then press the OK button.
    Long-Edge Feed Short-Edge Feed
    6300-007
    H6300-111
    X
    H6300-112
    X
    Downloaded From ManualsPrinter.com Manuals 
    						
    							Printing on Specialty Media
    Phaser® 6300/6350 Color Laser Printer
    3-41 7.If you selected New Custom Size, select the custom width and height:
    a.For Custom Width, use the Up Arrow and Down Arrow buttons to select the distance 
    between the Tray 1 (MPT) guides, and then press the OK button.
    b.For Custom Height, use the Up Arrow and Down Arrow buttons to select the height 
    of the paper, and then press the OK button.
    Note:When you define a new custom size, it is stored in the printer so it can be used 
    again. Up to five custom sizes can be stored in the printer. If you define a new custom size 
    after five custom sizes have been stored, the new custom size replaces the oldest custom 
    size defined.
    8.Either use the custom size as the document size in the application or select Tray 1 (MPT) 
    as the paper source.
    Downloaded From ManualsPrinter.com Manuals 
    						
    							Phaser® 6300/6350 Color Laser Printer
    4-1 This chapter includes:
    ■Controlling the Quality of Your Prints on page 4-2
    ■Solving Print-Quality Problems on page 4-5
    Print Quality
    Downloaded From ManualsPrinter.com Manuals 
    						
    							Controlling the Quality of Your Prints
    Phaser® 6300/6350 Color Laser Printer
    4-2
    Controlling the Quality of Your Prints
    This section includes:
    ■Selecting a Print-Quality Mode on page 4-2
    ■Adjusting Color on page 4-3
    The print-quality mode and TekColor
     correction directly control the quality of your prints. The 
    print-quality mode and paper type directly control the print speed. You can change these 
    settings in the printer driver or on the control panel.
    Note:Driver settings override the control panel settings.
    See also: 
    Advanced Features Guide at www.xerox.com/office/6300_6350support
    Selecting a Print-Quality Mode
    There are four print-quality modes:
    Note:The print job may take longer to process when you select the Enhanced or Photo print-
    quality mode.
    Print-Quality Mode Description
    AutomaticAutomatically selects the optimal print-quality mode for the paper type 
    selected. For example, Photo print-quality mode is used when printing 
    on Glossy Paper and Standard print-quality mode is used when printing 
    on Plain Paper. (This setting is only available in the printer driver.)
    StandardHigh-speed, general-purpose mode for crisp, bright, color prints. 
    Recommended for most office use and quick prints.
    EnhancedHigh-quality mode for fine lines and detail. Recommended for vibrant, 
    saturated, color prints. Balances printing speed with quality.
    PhotoHighest-quality mode for color prints and smoothest light colors. 
    Recommended for photographs, smooth shaded drawings, and vibrant 
    color.
    Downloaded From ManualsPrinter.com Manuals 
    						
    All Xerox manuals Comments (0)

    Related Manuals for Xerox Phaser 6350 DX User Manual