Yamaha 01v 96 I Manual

							Cascading Consoles111
01V96i—Reference Manual
Other Functions
Cascading Consoles
The 01V96i features a Cascade Bus that enables cascade con-
nection. You can connect two 01V96is in cascade using the 
digital inputs and outputs, or the OMNI IN and OMNI OUT 
connectors. In this way, two consoles work just like one big 
console, integrating each unit’s Buses 1–8, Aux Sends 1–8, 
Stereo Bus, and Solo Bus.
The following functions are linked between two cascaded 
01V96is via the MIDI IN and OUT ports.
• Display page selection
•Solo function
•Fader Mode
• Metering Position
• Peak Hold On/Off
• Meter Fast Fall on/off
• Scene Store, Recall, and Title Edit
The following paragraphs explain how to make a cascade 
connection using two 01V96is and the inputs and outputs of 
the digital I/O card installed in the slot of each 01V96i.
1.Install digital I/O cards into the slot on each 
of two 01V96is.
2.Connect two 01V96is as follows:
• Connect the digital I/O card output on the transmitting 
01V96i (slave) to the digital I/O card input on the receiv-
ing 01V96i (master).
• Connect the ADAT IN connector on the master unit to 
the ADAT OUT connector on the slave unit.
• Connect the MIDI IN port on the master unit to the 
MIDI OUT port on the slave unit using a MIDI cable.
• Connect the MIDI OUT port on the master unit to the 
MIDI IN port on the slave unit using a MIDI cable.
3.On the slave unit, press the DISPLAY ACCESS 
[PATCH] button repeatedly until the Patch | 
Out Patch page appears.
4.Assign the Bus signals to the channels that are 
used for the cascade connection.
The following signals are available:
The following display page is an example of integrating 
Bus 1–8, Aux Send 1–4, Stereo Bus, and Solo Bus signals 
via the ADAT IN and OUT connectors and two 8-chan-
nel digital I/O cards (such as MY8-AT).
5.On the master unit, press the DISPLAY 
ACCESS [PATCH] button repeatedly until the 
Patch | Cascade In page appears.
6.Select the Input Channels on the master unit 
to which the Bus signals are input from the 
Slave unit.
The following display page is an example of receiving the 
slave unit’s Bus 1–8, Aux Send 1–4, Stereo Bus, and Solo 
Tip: 
•To link functions and parameters (excluding the Solo func-
tion), turn on the Cascade COMM Link check box on the Setup 
| Prefer1 page (see page 109).
•T h e  S o l o  f u n c t i o n  i s  a l w a y s  l i n k e d  r e g a r d l e s s  o f  t h e  s t a t u s  o f  t h e  
Cascade COMM Link check box.
SOLO SOLO
ON ONSOLO
ONSOLO
ONSOLO
ONSOLO
ONSOLO
ONSOLO
ONSOLO
ONSOLO
ONSOLO
ONSOLO
ONSOLO
ONSOLO
ONSOLO
ONSOLO
ONSOLO
ONSOLO
ON ON
PEAK
SIGNAL PEAK
SIGNAL PEAK
SIGNAL PEAK
SIGNAL PEAK
SIGNAL PEAK
SIGNAL PEAK
SIGNAL PEAK
SIGNAL PEAK
SIGNAL PEAK
SIGNAL PEAK
SIGNAL PEAK
SIGNAL PEAK
SIGNAL PEAK
SIGNAL
1-16 17-32 MASTER REMOTELAYERSEL SEL SEL SEL SEL SEL SEL SEL SEL SEL SEL SEL SEL SEL SEL SEL SEL SELSELST IN ENTER
STEREODEC INCSOLO CLEAR
RECALL STORESCENE MEMORYPHONES
MONITOR
OUT
MONITOR
2TR IN CH15/16
2TR IN
LEVEL PHONES
LEVEL0
10 0
10+4-26
GAIN+4-26
GAIN+4-26
GAIN
GAIN+4-26
GAIN 20dB
-16 -60GAIN 20dB
-16 -60GAIN20dB 20dB 20dB 20dB 20dB 20dB 20dB 20dB 20dB 20dB
-16 -60
GAIN -16 -60
GAIN -16 -60
GAIN -16 -60GAIN -16 -60GAIN -16 -60GAIN -16 -60GAIN -16 -60GAIN -16 -60GAIN -16 -60PA D
FADER MODE DISPLAY ACCESSAUX 1
AUX 1AUX 2AUX 3AUX 4AUX 5AUX 6AUX 7AUX 8BUS 1BUS 2BUS 3BUS 4BUS 5BUS 6BUS 7BUS 8
AUX 2AUX 3AUX 4AUX 8AUX 7AUX 6AUX 5HOME (METER)
DYNAMICSEQ EFFECT VIEWPATCH UTILITY MIDI SCENEDIO/SETUP/ INSERT/
DELAYPAN/
ROUTINGPA I R /
GROUP
A
BA
BA
BA
BA
BA
BA
BA
BA
BA
BA
BA
B16 15 13 12 11 10 9 8 7 6 4 3 2 15
14INSERT I/O INSERT I/O INSERT I/O INSERT I/O INSERT I/O INSERT I/O INSERT I/O INSERT I/O INSERT I/OINSERT I/OINSERT I/OINSERT I/O
L
R
IN OUT2TR-10dBV (UNBAL)PHANTOM +48VCH9-12 CH5-8 CH1-4INPUT(BAL)
INSERT
OUT IN
(UNBAL)
ST IN 1 ST IN 2USER DEFINED
KEYS12
34
56
78 5 5 5 +10
510 10
1015 15
1520 20
2030 30 30
3040 40
4050 50
5060 60
70 70 20
3040
4050
5060
700 0
5
10
15
200
0 5 +10
5
10
15
30
20
3040
4050
5060
70 20
3040
4050
5060
70 20
3040
4050
5060
70 20
3040
4050
5060
70 20
3040
4050
5060
70150 5
10
15
200
5+10
5
100
30 155
10
15
200
5 +10
5
100
30 155
10
15
200
5 +10
5
100
30 155
10
15
200
5 +10
5
100
30 15
20
3040
4050
5060
70 30 15
20
3040
40 20
30
40 20
30
40 20
30
4050
50 50 50 50 20
30
40
50 20
30
40
5060
70 40
50
60
70 40
50
60
70 40
50
60
70 40
50
60
70 40
50
60
70 40
50
60
70 40
50
60
7030 155
10
15
200
5 +10
5
100 5
10
15
200
5 +10
5
100 5
10
15
200
305
10
15
200
305
10
15
200
305
10
15
200
305
10
15
200
30 30 305
10
15
200
5
10
15
200
5
10
15
200
5 +10
5
100
155 +10
5
100
155 +10
5
100
155 +10
5
100
15
2030
40
50 15 15
20
30
40
50 155 +10
5
100 5 +10
5
100 5 +10
5
100 5 +10
5
100123456 123456
78 9 10 11 12 78 9 10 11 12
13 14 15 16 13 14 15 1632 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17STEREO
13 14 15 16OVER
0
-3
-6
-9
-12
-15
-18
-24
-30
-36
-48HIGH
HIGH-MID
LOW-MID
LOW QFREQUENCYGAINSOLO SOLO
ON ONSOLO
ONSOLO
ONSOLO
ONSOLO
ONSOLO
ONSOLO
ONSOLO
ONSOLO
ONSOLO
ONSOLO
ONSOLO
ONSOLO
ONSOLO
ONSOLO
ONSOLO
ONSOLO
ON ON
PEAK
SIGNAL PEAK
SIGNAL PEAK
SIGNAL PEAK
SIGNAL PEAK
SIGNAL PEAK
SIGNAL PEAK
SIGNAL PEAK
SIGNAL PEAK
SIGNAL PEAK
SIGNAL PEAK
SIGNAL PEAK
SIGNAL PEAK
SIGNAL PEAK
SIGNAL
1-16 17-32 MASTER REMOTELAYERSEL SEL SEL SEL SEL SEL SEL SEL SEL SEL SEL SEL SEL SEL SEL SEL SEL SELSELST IN ENTER
STEREODEC INCSOLO CLEAR
RECALL STORESCENE MEMORYPHONES
MONITOR
OUT
MONITOR
2TR IN CH15/16
2TR IN
LEVEL PHONES
LEVEL0
10 0
10+4-26
GAIN+4-26
GAIN+4-26
GAIN
GAIN+4-26
GAIN 20dB
-16 -60GAIN 20dB
-16 -60GAIN20dB 20dB 20dB 20dB 20dB 20dB 20dB 20dB 20dB 20dB
-16 -60
GAIN -16 -60
GAIN -16 -60
GAIN -16 -60GAIN -16 -60GAIN -16 -60GAIN -16 -60GAIN -16 -60GAIN -16 -60GAIN -16 -60PA D
FADER MODE DISPLAY ACCESSAUX 1
AUX 1AUX 2AUX 3AUX 4AUX 5AUX 6AUX 7AU X 8BUS 1BUS 2BUS 3BUS 4BUS 5BUS 6BUS 7BUS 8
AUX 2AUX 3AUX 4AUX 8AUX 7AUX 6AUX 5HOME (METER)
DYNAMICSEQ EFFECT VIEWPATCH UTILITY MIDI SCENEDIO/SETUP/ INSERT/
DELAYPAN/
ROUTINGPA I R /
GROUP
A
BA
BA
BA
BA
BA
BA
BA
BA
BA
BA
BA
B16 15 13 12 11 10 9 8 7 6 4 3 2 15
14INSERT I/O INSERT I/OINSERT I/O INSERT I/OINSERT I/O INSERT I/O INSERT I/O INSERT I/O INSERT I/OINSERT I/OINSERT I/OINSERT I/O
L
R
IN OUT2TR-10dBV (UNBAL)PHANTOM +48VCH9-12 CH5-8 CH1-4INPUT(BAL)
INSERT
OUT IN
(UNBAL)
ST IN 1 ST IN 2USER DEFINED
KEYS12
34
56
78 5 5 5 +10
510 10
1015 15
1520 20
2030 30 30
3040 40
4050 50
5060 60
70 70 20
3040
4050
5060
700 0
5
10
15
200
0 5 +10
5
10
15
30
20
3040
4050
5060
70 20
3040
4050
5060
70 20
3040
4050
5060
70 20
3040
4050
5060
70 20
3040
4050
5060
70150 5
10
15
200
5+10
5
100
30 155
10
15
200
5 +10
5
100
30 155
10
15
200
5 +10
5
100
30 155
10
15
200
5 +10
5
100
30 15
20
3040
4050
5060
70 30 15
20
3040
40 20
30
40 20
30
40 20
30
4050
50 50 50 50 20
30
40
50 20
30
40
5060
70 40
50
60
70 40
50
60
70 40
50
60
70 40
50
60
70 40
50
60
70 40
50
60
70 40
50
60
7030 155
10
15
200
5 +10
5
100 5
10
15
200
5 +10
5
100 5
10
15
200
305
10
15
200
305
10
15
200
305
10
15
200
305
10
15
200
30 30 305
10
15
200
5
10
15
200
5
10
15
200
5 +10
5
100
155 +10
5
100
155 +10
5
100
155 +10
5
100
15
2030
40
50 15 15
20
30
40
50 155 +10
5
100 5 +10
5
100 5 +10
5
100 5 +10
5
100123456 123456
78 9 10 11 12 78 9 10 11 12
13 14 15 16 13 14 15 1632 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17STEREO
13 14 15 16OVER
0
-3
-6
-9
-12
-15
-18
-24
-30
-36
-48HIGH
HIGH-MID
LOW-MID
LOW QFREQUENCYGAIN
MY8-AT 
etc.
SLOT
MY8-AT 
etc.
SLOT
01V96i (Slave) 01V96i (Master)
OUT IN
ADAT 
OUT 
connector
MIDI 
IN/OUT 
connector
ADAT 
IN 
connector
MIDI 
IN/OUT 
connector
Options Description
CAS BUS1–BUS8Bus 1–8 Cascade Outs
CAS AUX1–AUX8Aux Bus 1–8 Cascade Outs
CAS ST-L, CAS ST-RStereo Bus L & R Cascade 
Outs
CASSOLOL, CASSOLORSolo Bus L & R Cascade 
Outs
Tip : Patching may vary depending on the type and number 
of buses used for the cascade connection.
Note: Since the number of channels available on the digital 
I/O card is limited, only Aux Sends 1–4 are cascaded in this 
example. Using a 16-channel digital I/O card (such as 
MY16-AT) enables you to cascade all buses. 
						

							112Other Functions
01V96i—Reference Manual
Bus signals via the ADAT IN and OUT connectors and 
two 8-channel digital I/O cards (such as MY8-AT).
7.On the master unit, press the DISPLAY 
ACCESS [DIO/SETUP] button repeatedly until 
the DIO/Setup | Cascade page appears, then 
adjust the Attenuators using the parameter 
controls.
The DIO/Setup | Cascade page enables you to adjust the 
level of signals input to the Cascade Bus using the dedi-
cated attenuators. You can also turn the Cascade Buses on 
or off using the buttons below the parameter controls.
8.Press the DISPLAY ACCESS [DIO/SETUP] but-
ton repeatedly to display the DIO/Setup | 
MIDI/Host page, then set the Cascade Link 
parameter to “MIDI.”
9.Repeat Step 8 for the master unit.
After Steps 8 and 9, the slave unit will be able to transmit 
and receive MIDI messages.
10.To match the parameters of both 01V96is, 
locate the DIO/Setup | MIDI/Host page on 
the copy source unit.
Move the cursor to the TRANSMIT button for 
the SYNC parameter, then press [ENTER].
Parameters for cascade link (page 111) will be copied to 
the other 01V96i via the REMOTE connector. If you 
select the REQUEST button instead of the TRANSMIT 
button for the SYNC parameter, you can reverse the copy 
direction.
At this point, Bus 1–8, Aux 1–4, and the Stereo Bus on 
both 01V96is are integrated, and the data is output via 
Bus Outs 1–8, Aux Outs 1–4, and the Stereo Out on the 
master unit. If you solo channels on one of the 01V96is, 
you can monitor the soloed signals via the Monitor out-
puts.
Note: Be sure to patch the slave Bus signals to the same Buses 
on the master unit. Incorrect patching will result in an incor-
rect cascade connection.  
						

							Checking the Battery and the System Version113
01V96i—Reference Manual
Other Functions
Checking the Battery and 
the System Version
The Utility | Battery page enables you to check the condition 
of the internal memory-backup battery and the system ver-
sion number. To locate this page, press the DISPLAY ACCESS 
[UTILITY] button repeatedly.
1Status
If the Status is “Okay,” the battery has sufficient voltage for 
operation. If the Status is “Voltage Low!,” ask your 
Yamaha dealer or authorized Yamaha service center to 
replace the battery as soon as possible. Failure to replace 
a low battery may result in data loss. 
2Ver X.XX (X.XX represents the version number.)
This indicator identifies the system version number. 
Check the current system version number before you 
update the firmware.
Visit the following website to check the latest system ver-
sion number:
http://www.yamahaproaudio.com/
Calibrating the Faders
The 01V96i motorized fader positions may shift over time 
depending on the operating conditions and environment. 
You can correct the shifted faders using the Calibration func-
tion.
1.Make sure that the power to the 01V96i is 
turned off.
2.Press and hold down the [ENTER] button, 
then turn on the POWER ON/OFF switch.
After a while, the following calibration window appears.
3.Make sure that “1 FADER MOVE & FADER 
POSITION” is selected, then press [ENTER].
To adjust only the motor fader movement, use the cursor 
buttons to select “2 FADER MOVE ONLY,” then press 
[ENTER].
To adjust only the fader position, use the cursor buttons 
to select “3 FADER POSITION ONLY,” then press 
[ENTER]. Proceed to Step 5.
To cancel the calibration operation, use the cursor but-
tons to select “4 QUIT,” then press [ENTER]. The 01V96i 
starts in normal mode.
4.The calibration operation begins, adjusting 
the motor fader movement, and the 01V96i 
displays a message that indicates the calibra-
tion operation is in progress.
The calibration operation takes about two minutes. DO 
NOT touch the faders during the operation.
Note: Do not attempt to replace the battery yourself as a mal-
function may occur.
1
2 
						

							114Other Functions
01V96i—Reference Manual
5.When the calibration operation is complete, 
the 01V96i displays a window in which you 
can select faders for position adjustment.
If you selected “2 FADER MOVE ONLY” in Step 3, the 
fader adjustment is complete. The 01V96i starts in nor-
mal mode.
6.Use the channel [SEL] buttons to select faders 
for which you wish to calibrate the position, 
then press [ENTER].
The selected channel [SEL] button indicators flash. 
(When you press [ENTER], they light up steadily.) At the 
beginning, all [SEL] buttons are flashing. However, if an 
error occurs and the unit is trying calibration again, only 
the [SEL] button indicator of a problematic fader flashes.
7.Follow the instruction in the window to set 
the position of the selected faders to –, then 
press [ENTER].
8.Set the position of the selected faders to the 
level instructed in the window, then press 
[ENTER]. Set faders 1–16 to –15, and Stereo 
fader to –30.
9.Set the position of the selected faders to the 
level instructed in the window, then press 
[ENTER]. Set faders 1–16 to 0, and Stereo 
fader to any position.
10.Set the position of the selected faders to the 
level instructed in the window, then press 
[ENTER]. Set faders 1–16 to +10, and Stereo 
fader to 0.
If there is no problem with the calibration result, this con-
cludes the calibration operation. The 01V96i will start in 
normal mode.
11.If there is any problem with the calibration 
result, the 01V96i displays the following win-
dow.
Also, the channel [SEL] button indicator of a problematic 
fader flashes.
Use the cursor buttons to select one of the following three 
options, then press [ENTER].
•CONTINUE
While the [SEL] button indicator of a problematic fader is 
flashing, the calibration process returns to Step 5.
• START FROM THE BEGINNING
The calibration process returns to Step 2.
•QUIT ANYWAY
The 01V96i cancels the calibration operation and starts in 
normal mode. The standard setting will be applied to 
problematic faders.
If this window appears after you try the calibration pro-
cess several times, consult your nearest Yamaha dealer.
If the calibration data has some problems, the 01V96i dis-
plays the following window when it starts up. In this case, 
calibrate the position of the faders specified in the win-
dow. 
						

							Index115
01V96i—Reference Manual
Index
Index
Symbols
/INS/DLY | DLY 1-16 page ............ 18
/INS/DLY | DLY 17-32 page
 ......... 18
/INS/DLY | Insert page
 ............ 47, 65
/INS/DLY | Out Dly page
 ........ 30, 37
/INS/DLY | Phase page
 ................... 18
/INSERT/DELAY button
 ................. 8
+48V ON/OFF switches
 ....................... 10
Numerics
1–16/17–32 buttons ................................ 8
1–8 buttons
 ............................................... 9
2TR IN connectors
 ............................7, 12
2TR IN DIGITAL COAXIAL
 ............. 10
2TR IN DIGITAL connector
 .............. 13
2TR OUT connectors
 .......................7, 13
2TR OUT DIGITAL COAXIAL
 ........ 10
2TR OUT DIGITAL connector
 .......... 13
A
AC IN connector ................................... 11
AD input
 ................................................... 7
AD output section
 ................................. 10
AD15/16 selector
 ..................................... 7
ADAT IN/OUT connector
 ........... 10, 13
Add-On Effects
 ...................................... 67
AMP SIMULATE
 ............................... 136
Analog inputs & outputs
 ...................... 12
Assigne
Control changes
 ........................... 104
MIDI messages
 ............................... 96
Program changes
 .......................... 103
Remote Layer
 .................................. 83
USER DEFINED KEYS
 ................ 87
Attenuator
 ................................. 20, 30, 36
Output signals
 ................................. 34
Auto Channel Select preference
 ....... 109
Auto Direct Out On preference
 ........ 109
Auto EQUALIZER Display preference
 .................................................. 109
AUTO PAN
 ......................................... 135
Auto PAN Display preference
 .......... 109
Auto SOLO Display preference
 ........ 109
Auto update function
 ........................... 70
Auto WORD CLOCK Display 
preference
 ............................... 109
AUX 1–AUX 8 buttons
 .......................... 8
Aux outs
 .................................................. 36
Aux send mode
 ......................... 38, 39, 41
Aux sends
 ............................................... 38
Attenuating
 ..................................... 36
Comp settings
 ................................. 37
Copying channel fader positions
 ............................................ 42
Delaying
 ........................................... 37
EQ settings
 ............................... 37, 38
Fixed mode
 ...................................... 39
Panning
 ............................................ 41Setting from the control surface
 .............................................38
Setting from the display
 ......... 36, 38
Setting levels
 ....................................38
Variable mode
 .................................39
Viewing settings
 ..............................37
Viewing settings for multiple 
channels
 .............................40
Aux1 | View1-16 page
 ...........................40
Aux1 | View17-STI page
 .......................40
B
Balancing .................................................33
Battery
 ................................................... 113
Bulk dump
 ........................................... 107
Messages
 ....................................... 100
Bus out
 .....................................................29
Attenuating
 ......................................30
Compressing
 ...................................30
Delaying
 ...........................................30
EQ’ing
 ...............................................31
EQ’ing and Balancing
 ....................33
Naming
 ............................................35
Pairing
 ..............................................33
Routing signals to the stereo bus
 .............................................31
Setting from the control surface
 .............................................33
Setting from the display
 ................30
Setting the levels
 .............................33
Viewing the settings
 .......................31
BUS1–BUS8
 ............................................54
C
Cascade COMM Link preference .... 109
Cascading consoles
 ............................. 111
Cascade page
 ................................ 112
SYNC parameter
 ......................... 112
CATEGORY
 ...........................................14
CH1–4 ON/OFF switch
 .......................10
CH5–8 ON/OFF switch
 .......................10
CH9–12 ON/OFF switch
 .....................10
Channel Copy Parameter preference
 ................................................. 110
Channel faders
 .........................................7
Channel ID/Channel preference
 ...... 110
Channel library
 ......................................75
Channel strip section
 ..............................7
CHORUS
 ............................................. 134
CLEAR button
 .........................................9
Comp260/Comp260S
 ........................ 142
Compressor library
 ...............................79
Preset
 ................................................80
Compressors
 ............................. 20, 30, 37
Compressor link
 .............................59
Linking
 .............................................62
Contrast control
 .......................................9
Control changes
 ..........................100, 104
Control surface
 .........................................6
AD input section
 ..............................7
Channel strip section
 .......................7
Data entry section
 .............................9
DISPLAY ACCESS section
 .............8Display section
 ................................. 9
FADER MODE section
 .................. 8
LAYER section
 ................................. 8
Monitor out & Headphones section
 .............................................. 7
SCENE MEMORY section
 ............. 9
SELECTED CHANNEL section
 ... 9
SOLO section
 .................................... 9
ST IN section
 .................................... 8
STEREO section
 ............................... 8
USER DEFINED KEYS section
 ..... 9
Control Surface & Rear Panel
 ............... 6
COPY
 ...................................................... 15
Cursor buttons
 ......................................... 9
D
Data entry section ................................... 9
DAW
 ....................................................... 93
Nuendo/Cubase
 ............................. 93
Other
 ................................................ 94
Pro tools
 ........................................... 83
Remote
 ............................................. 83
DEC & INC buttons
 ............................... 9
Delay
 ........................................... 18, 30, 37
DELAY SCALE
 .............................. 18
FB.GAIN
 ......................................... 19
DELAY LCR
 ........................................ 133
DELAY SCALE
 ..................................... 18
DELAY+ER.
 ......................................... 139
DELAY+REV
 ...................................... 140
DELAY->ER.
 ....................................... 139
DELAY->REV
 ..................................... 140
Digital I/O section
 ................................. 10
Digital inputs & outputs
 ...................... 13
DIO Warning preference
 ................... 109
DIO/Setup | Cascade page
 ................. 112
DIO/Setup | Format page
 ..............15, 16
DIO/Setup | Insert page
 ....................... 85
DIO/Setup | Machine page
 .................. 98
DIO/Setup | Meter page
 ....................... 86
DIO/Setup | MIDI/Host page
............................. 84
, 98, 101, 112
DIO/Setup | Monitor page
 .................. 49
DIO/Setup | Output Att page
 .............. 34
DIO/Setup | Prefer1 page
 .................. 109
DIO/Setup | Prefer2 page
 .................. 109
DIO/Setup | Remote page
 ..... 85, 95, 110
DIO/Setup | Surr Bus page
 .................. 54
DIO/Setup | Word Clock page
 ........... 14
DIO/SETUP button
 ................................ 8
Direct outs
 .............................................. 46
Display
 ...................................................... 9
DISPLAY ACCESS section
 ................... 8
Display Brightness preference
 .......... 110
Display section
 ......................................... 9
DIST->DELAY
 .................................... 140
DISTORTION
 ..................................... 136
Dithering
 ................................................ 15
DIV
 .......................................................... 56
DOUBLE CHANNEL
 .......................... 16
DOUBLE SPEED
 .................................. 16
Dual Phaser
 .......................................... 145
DUAL PITCH
 ..................................... 135 
						

							116Index
01V96i—Reference Manual
DYNA. FILTER .................................. 136
DYNA. FLANGE
 ................................ 136
DYNA. PHASER
 ................................ 137
Dynamics | Comp Edit page
 .. 20, 30, 37
Dynamics | Comp Lib page
 ................. 79
Dynamics | Gate Edit page
 .................. 19
Dynamics | Gate Lib page
 ................... 79
DYNAMICS button
 ................................8
E
EARLY REF. ........................................ 132
ECHO
 ................................................... 134
Effect | FX1 Edit page
 ........................... 66
Effect | FX1 Lib page
 ............................ 76
Effect | FX2 Edit page
 ........................... 66
Effect | FX2 Lib page
 ............................ 76
Effect | FX3 Edit page
 ........................... 66
Effect | FX3 Lib page
 ............................ 76
Effect | FX4 Edit page
 ........................... 66
Effect | FX4 Lib page
 ............................ 76
Effect | P-In Edit page
 .......................... 67
EFFECT button
 ........................................8
Effects
Bypass
 .............................................. 66
Internal effects
 ................................ 64
parameter tables
 ........................... 132
Plug-ins
 ........................................... 67
Effects library
 ......................................... 76
Preset
 ............................................... 77
programs
 ......................................... 77
EMPHASIS
 ............................................ 14
ENTER button
 .........................................9
EQ
 .................................. 21, 31, 33, 37, 38
frequency
 ........................................ 21
gain
 ................................................... 21
Q
 ....................................................... 21
EQ | EQ Edit page
 .................... 21, 31, 37
EQ | EQ Library page
 ........................... 81
EQ | Out Att page
 ........................... 30, 36
EQ button
 .................................................8
EQ library
 ............................................... 81
Preset
 ............................................... 81
EQ link
 .................................................... 59
Equalizer601
 ........................................ 143
F
F/R ........................................................... 56
F1–F4 buttons
 ..........................................9
Fader groups
 .......................................... 59
FADER MODE section
 ..........................8
Fading
 ..................................................... 71
ALL CLEAR
 ................................... 71
AUX1–8
 .......................................... 71
BUS1–8
 ............................................ 71
Global fade time
 ............................. 71
INPUT CH1–32
 ............................. 71
ST IN 1–4
 ........................................ 71
STEREO
 .......................................... 71
FAST
 ....................................................... 56
Fast Meter Fall Time preference
 ...... 109
FB.GAIN
 ................................................ 19
Fixed mode
 ...................................... 39, 41
FLANGE
 .............................................. 134FREQUENCY control
 ............................ 9
FS
 ............................................................. 14
G
GAIN controls .............................. 7, 9, 12
GANG
 ..................................................... 22
Gate library
 ............................................. 79
GATE REVERB
 ................................... 132
Gates
 ........................................................ 19
KEYIN SOURCE
 ........................... 19
Global Paste
 ............................................ 73
Group
 ...................................................... 59
Fader groups
 ................................... 59
Mute groups
 .................................... 59
H
HIGH button ........................................... 9
Higher sampling rates
 .......................... 16
HIGH-MID button
 ................................. 9
HOME button
 ......................................... 8
HORIZONTAL
 ..................................... 27
HQ. PITCH
 .......................................... 135
I
INDIVIDUAL ....................................... 22
INIT
 ......................................................... 54
Initial Data Nominal preference
 ....... 109
Input channels
 ....................................... 17
Attenuating
 ..................................... 20
Compressing
 ................................... 20
Delaying
 ........................................... 18
EQ
 ..................................................... 25
EQ’ing
 .............................................. 21
Gating
 .............................................. 19
Levels
 ................................................ 25
Naming
 ............................................ 28
Pairing
 .............................................. 26
Panning
 ..................................... 22, 25
Routing
 ............................................ 22
Setting from the control surface
 .. 25
Setting from the display
 ................ 18
Switching the signal phase
 ............ 18
Viewing the settings
 ...................... 23
INPUT connectors
 ............................7, 12
Input patch
 ............................................. 43
Initial settings
 ............................... 123
Parameters
 .................................... 121
Input patch library
 ................................ 75
Input section
 .......................................... 12
Input sensitivity
GAIN controls
 .................................. 7
INSERT I/O connectors
 ...................7, 12
Insert in
 ................................................... 48
Insert patching
 ....................................... 47
Internal effects
Aux sends
 ........................................ 64
Editing
 .............................................. 66
Effects processors 1–4
 ................... 64
Inserting into channels
 ................. 65
Meters
 .............................................. 67
MIX BALANCE
 ............................. 66
TEMPO
 ........................................... 66
INV GANG
 ............................................ 22
K
KEYIN SOURCE ...................................19
L
LAST SOLO ............................................50
LATCH
 ....................................................97
LAYER section
 ......................................... 8
Layers
Initial bank settings
 ..................... 128
LEARN button
 .......................................96
Level controls
 ........................................... 8
Levels
 ................................................ 33, 38
LFE
 ...........................................................56
Libraries
 ...................................................74
Channel library
 ...............................75
Compressor library
 ........................79
Effects library
 ..................................76
EQ library
 ........................................81
Gate library
 ......................................79
General operation
 ..........................74
Input patch library
 .........................75
Output patch library
 ......................76
Link
 ..........................................................59
Compressors
 ...................................62
EQ
 .....................................................62
LOW button
 ............................................. 9
LOW-MID button
 ................................... 9
M
M.BAND DYNA. ............................... 142
Machine control
 ....................................98
MASTER button
 ...................................... 8
Max 100
 ................................................ 144
Meters
Stereo meters
 ..................................... 9
MIDI
 ............................................... 84, 100
Bulk dump
 .................................... 107
Bulk dump messages
 .................. 100
Control changes
 ........................... 104
Data format
 .................................. 173
FADER H/L
 .................................. 106
Initial parameter to control 
change table
 ................... 157
MIDI IN/THRU/OUT ports
..................................... 10
, 100
MIDI note on/off
 ......................... 100
Parameter changes
 ...................... 106
Parameters
 .................................... 104
Program changes
 ......................... 103
Scene memory to program 
change table
 ................... 156
Setup
 .............................................. 101
SLOT
 ............................................. 100
System exclusive messages
 ......... 100
Transmission and Reception
 ..... 102
USB port
 ....................................... 100
MIDI | Bulk page
 ................................ 107
MIDI | Ctl Asgn page
 ......................... 104
MIDI | Pgm Asgn page
 ...................... 103
MIDI | Setup page
 .............................. 102
MIDI button
 ............................................. 8
MIDI IN/THRU/OUT ports
 ...............10
MIDI machine control
 ...................... 100 
						

							Index117
01V96i—Reference Manual
IndexMIDI remote .......................................... 94
Banks
 ................................................ 94
LATCH
 ............................................ 97
LEARN button
 ............................... 96
MIDI messages
 ............................... 96
TARGET parameter
 ...................... 95
UNLATCH
 ..................................... 97
MIDI Warning preference
 ................ 109
MIDI/USB Section
 ................................ 10
MIX SOLO
 ............................................. 50
MIXDOWN
 ........................................... 49
MMC
 .............................................. 98, 100
MOD. DELAY
 ..................................... 133
MOD. FILTER
 ..................................... 136
MONITOR LEVEL control
 ................... 7
Monitor out & Headphones section
 ...................................................... 7
MONITOR OUT connectors
 ...... 10, 13
Monitor Source selector
 ......................... 7
Monitoring
 ............................................. 49
Digital input channel status
 ......... 14
LAST SOLO
 .................................... 50
MIX SOLO
 ...................................... 50
MIXDOWN
 .................................... 49
MONO
 ............................................. 50
RECORDING
 ................................. 49
Solo function
 ................................... 51
Solo safe function
 ........................... 50
Solo setup
 ........................................ 49
MONO
 .................................................... 50
MONO DELAY
 ................................... 132
MULTI FILTER
 ................................... 141
Mute groups
 ........................................... 59
Muting
 ..................................................... 89
N
Naming ............................................ 28, 35
Nominal Pan preference
 .................... 109
Nuendo
 ................................................... 83
Nuendo/Cubase
 ..................................... 93
O
OMNI OUT connectors ............... 10, 13
ON buttons
 ...........................................7, 8
OpenDeck
 ............................................. 143
Other functions
 ................................... 109
Preferences
 .................................... 109
Output patch
 .......................................... 44
Initial settings
 ............................... 127
Parameters
 ..................................... 125
Output patch library
 ............................. 76
Output section
 ....................................... 13
P
PAD switches .....................................7, 12
Pair Confirmation preference
 ........... 109
PAIR/GROUP button
 ............................ 8
Pair/Grup | In Comp page
 ................... 63
Pair/Grup | In EQ page
 ........................ 62
Pair/Grup | In Fader page
 .................... 59
Pair/Grup | In Mute page
 .................... 59
Pair/Grup | Input page
 ......................... 27
Pair/Grup | Out Comp page
 ................ 63Pair/Grup | Out EQ page
 ......................62
Pair/Grup | Out Fader page
 .................59
Pair/Grup | Out Mute page
 ..................60
Pair/Grup | Output page
 ......................33
Pairing
 .............................................. 26, 33
HORIZONTAL
 ..............................27
Using the display
 ............................27
Using the SEL buttons
 ...................27
VERTICAL
 ......................................27
PAN control
 .............................................9
Pan/Route | Bus To St page
 ..................31
Pan/Route | Ch Edit page
 .....................56
Pan/Route | Pan page
 ............................25
Pan/Route | ROUT1-16 page
 ..............22
Pan/Route | ROUT17-ST1 page
 ..........22
Pan/Route | Surr ST IN page
 ...............58
Pan/Route | Surr1-16 page
 ...................58
Pan/Route | Surr17-32 page
 .................58
PAN/ROUTING button
 ........................8
Pan/Surr | Surr Mode page
 ..................53
PAN/SURR LINK
 ..................................53
Panning
 ............................................ 22, 41
F.S
 ......................................................34
FOLLOW PAN
 ...............................24
GANG
 ..............................................22
INDIVIDUAL
 .................................22
INV GANG
 .....................................22
PAN buttons
 ...................................22
Parameter changes
 ............................. 106
Parameter lists
 ..................................... 119
Parameter wheel
 ......................................9
Patch | 2TR Out page
 ............................45
Patch | Cascade In page
 ..................... 111
Patch | Direct Out page
 ........................46
Patch | Effect page
 ..................................64
Patch | IN LIB page
 ...............................75
Patch | IN Name page
 ...........................28
Patch | In Patch page
 .............................43
Patch | Insert In page
 ............................48
Patch | Out LIB page
 .............................76
Patch | Out Name page
 .........................35
Patch | Out Patch page
 ................. 44, 111
Patch | USB OUT page
 .........................45
PATCH button
 ................................. 8, 43
Patch Confirmation preference
 ........ 109
Patching
 ...................................................43
2TR digital outputs
 ........................45
ADAT OUT connector
 .................44
Direct outs
 .......................................46
Input patching
 ................................43
Insert in
 ............................................48
Insert patching
 ................................47
OMNI OUT connector
 .................44
Output patching
 .............................44
TO HOST USB channels
 ..............43
PEAK indicators
 ............................... 7, 12
PHANTOM +48V
 .................................10
Phantom Power
 .....................................12
CH1–4 ON/OFF switch
 ................10
CH5–8 ON/OFF switch
 ................10
CH9–12 ON/OFF switch
 ..............10
Phase
 ........................................................18
PHASER
 ............................................... 135PHONES jack
 ....................................7, 49
PHONES LEVEL control
 ...................... 7
PLUG-IN
 .............................................. 107
Plug-ins
 ................................................... 90
POWER ON/OFF switch
 .................... 11
Power section
 ......................................... 11
Prefer1 page
 ......................................... 109
Prefer2 page
 ......................................... 110
Preferences
 ........................................... 109
Pro tools
 ............................................83, 89
Automation
 ..................................... 93
Channel display mode
 .................. 86
Channel levels
 ................................. 89
Control surface operation
 ............ 87
Explicit mute
 ................................... 89
Flip mode
 ........................................ 90
Implicit mute
 .................................. 89
Insert display mode
 ....................... 85
Meter display mode
 ....................... 86
MIDI
 ................................................ 84
Muting
 ............................................. 90
Panning
 ......................................89, 90
Plug-ins
 ............................................ 90
Pre or Post
 ....................................... 90
Scrub & Shuttle
 .............................. 92
Selecting
 ........................................... 89
Send levels
 ....................................... 90
Soloing
 ............................................. 90
Program changes
 ........................ 100, 103
PROTECT button
 ................................. 69
Q
Q control .................................................. 9
Q, EQ
 ....................................................... 21
R
Rear Panel
PHANTOM +48V
 ......................... 10
Rear panel
 ............................................... 10
AD output section
 ......................... 10
Digital I/O section
 ......................... 10
MIDI/USB Section
 ........................ 10
Power section
 ................................. 11
SLOT section
 .................................. 11
RECALL button
 ...................................... 9
Recall Confirmation preference
 ....... 109
Recall safe function
 ............................... 72
RECORDING
 ........................................ 49
Remote
 .................................................... 83
FRAMES
 .......................................... 99
Insert display mode
 ....................... 85
LOCATE/TIME section
 ............... 98
Machine control
 .......................83, 98
MACHINE CONTROL section
 ............................................ 98
MIDI messages
 ............................... 96
MIDI remote
 .................................. 94
Nuendo
 ............................................ 83
ProTools
 .......................................... 83
REMOTE
 ......................................... 83
Target parameter
 ........................... 85
TRACK ARMING section
 ........... 98
TRANSPORT section
 ................... 99 
						

							118Index
01V96i—Reference Manual
REMOTE button .............................. 8, 83
Remote Layer
Nuendo/Cubase
 ............................. 93
Pro tools
 .......................................... 83
RESET BOTH
 ....................................... 27
REV+CHORUS
 .................................. 137
REV+FLANGE
 ................................... 137
REV+SYMPHO.
 ................................. 138
REV->CHORUS
 ................................. 137
REV->FLANGE
 .................................. 138
REV->PAN
 .......................................... 138
REV->SYMPHO.
 ................................ 138
REVERB HALL
 ................................... 132
REVERB PLATE
 ................................. 132
REVERB ROOM
 ................................ 132
REVERB STAGE
 ................................ 132
REVERSE GATE
 ................................ 132
REV-X
 .................................................. 144
RING MOD.
 ........................................ 136
ROTARY
 .............................................. 136
Routing
 ................................................... 22
Routing ST Pair Link preference
 ..... 110
S
Sampling rates ....................................... 14
DOUBLE CHANNEL
 .................. 16
DOUBLE SPEED
 ........................... 16
Setting the higher sampling rates
 ............................................ 16
SINGLE
 ........................................... 16
SRC sections
 ................................... 14
Scene | In Fade page
 ............................. 71
Scene | Out Fade page
 .......................... 71
Scene | Rcl Safe page
 ............................. 72
Scene | Scene page
 ................................ 69
Scene | Sort page
 ................................... 72
SCENE button
 ..........................................8
Scene MEM Auto Update preference
 ................................................. 109
Scene memories
 .................................... 68
Auto update function
 ................... 70
Edit indicators
 ................................ 68
Fading
 .............................................. 71
PROTECT button
 ......................... 69
Recall safe function
 ....................... 72
Scene numbers
 ............................... 68
Shadow memory
 ............................ 70
Sorting
 ............................................. 72
Storing & Recalling
 ....................... 69
Using the Scene Memory Page
 ... 69
What is stored
 ................................ 68
Scene memory #00
 ............................... 68
Scene memory #Ud
 .............................. 68
SCENE MEMORY section
 .....................9
Scene numbers
 ...................................... 68
Scene up/down buttons
 ..........................9
SEL buttons
 .......................................... 7, 8
SELECTED CHANNEL section
 ...........9
Setting levels
 .......................................... 38
Shadow memory
 ................................... 70
SIGNAL indicators
 ........................... 7, 12
SINGLE
 .................................................. 16
SLOT
 ........................................ 11, 13, 100SLOT section
 .......................................... 11
Solo
 .......................................................... 49
LAST SOLO
 .................................... 50
LISTEN
 ............................................ 50
MIX SOLO
 ...................................... 50
MIXDOWN
 .................................... 49
RECORDING
 ................................. 49
SOLO
 ............................................... 49
Solo function
 ................................... 51
SOLO SAFE CHANNEL
 .............. 50
Solo safe function
 ........................... 50
SOLO TRIM
 ................................... 50
SOLO buttons
 ...................................... 7, 8
SOLO indicator
 ....................................... 9
SOLO section
 ........................................... 9
SRC sections
 ........................................... 14
ST IN button
 ............................................ 8
ST IN section
 ........................................... 8
STEREO DELAY
 ................................ 133
STEREO fader
 .......................................... 8
Stereo meters
 ............................................ 9
Stereo out
 ................................................ 29
Attenuating
 ..................................... 30
Compressing
 ................................... 30
Delaying
 ........................................... 30
EQ’ing
 .............................................. 31
EQ’ing and Balancing
 ................... 33
Naming
 ............................................ 35
Pairing
 .............................................. 33
Setting from the control surface
 ............................................ 33
Setting from the display
 ................ 30
Setting the levels
 ............................. 33
Viewing the settings
 ...................... 31
STEREO OUT connectors
 ........... 10, 13
STEREO section
 ...................................... 8
STORE button
 ......................................... 9
Store Confirmation preference
 ......... 109
Storing and Recalling
 ........................... 69
Surround
 ................................................. 52
BUS1–BUS8
 .................................... 54
DIV
 ................................................... 56
F.S
 ..................................................... 34
F/R
 .................................................... 56
FAST
 ................................................ 56
INIT
 .................................................. 54
LFE
 ................................................... 56
LINK
 ................................................ 56
Pan graph
 ........................................ 56
PAN/SURR LINK
 .......................... 53
Panning
 ............................................ 56
PATTERN
 ....................................... 56
Setting up and Selecting
 ................ 53
ST LINK
 .......................................... 56
SURROUND MODE
 ............. 23, 53
Trajectory patterns
 ........................ 56
SURROUND MODE
 ........................... 53
Surround modes
 ............................. 52, 53
Factory-default
 ............................... 52
SYMPHONIC
 ...................................... 134
SYNC parameter
 ................................. 112
System exclusive messages
 ................ 100
System version
 ..................................... 113
T
Tab scroll buttons .................................... 9
Target parameter
 ...................................85
TO HOST USB port
 ..............................10
Trajectory patterns
 ................................57
TREMOLO
 .......................................... 135
U
UNLATCH .............................................97
USB
 ..........................................................10
USB port
 ....................................... 100
USB OUT page
 ......................................45
User assignable layer
 .......................... 110
USER DEFINED KEYS
 .......................... 9
Initial assignments
 ...................... 121
Utility | Battery page
 .......................... 113
Utility | CH Status page
 ........................14
UTILITY button
 ...................................... 8
V
Variable mode ................................. 39, 41
VERTICAL
 .............................................27
View | Fader page
 .................... 24, 32, 38
View | Library page
 ...............................75
View | Parameter page
 ............ 23, 31, 37
VIEW button
 ............................................ 8
Vintage Phaser
 .................................... 144
W
Window
Changing the surround mode
 ......53
Channel Pairing
 ..............................27
Copy operation
 ...............................42
WORD CLOCK IN connector
 ............10
WORD CLOCK OUT connector
 .......10 
						

							USER DEFINED KEYS119
Appendix: Parameter Lists
01V96i—Reference Manual
Appendix: Parameter Lists
USER DEFINED KEYS
#Function Display
0 No Assign No Assign
1 Scene MEM. Recall +1 Scene  +1 Recall
2 Scene MEM. Recall –1 Scene  –1 Recall
3 Scene MEM. Recall No. XX Scene  XX Recall
4 Effect-1 Lib. Recall +1 Fx1 Lib+1 Recall
5 Effect-1 Lib. Recall –1 Fx1 Lib–1 Recall
6 Effect-1 Lib. Recall No.XX Fx1 LibXXX  RCL.
7 Effect-2 Lib. Recall +1 Fx2 Lib+1 Recall
8 Effect-2 Lib. Recall –1 Fx2 Lib–1 Recall
9 Effect-2 Lib. Recall No.XX Fx2 LibXXX  RCL.
10 Effect-3 Lib. Recall +1 Fx3 Lib+1 Recall
11 Effect-3 Lib. Recall –1 Fx3 Lib–1 Recall
12 Effect-3 Lib. Recall No.XX Fx3 LibXXX  RCL.
13 Effect-4 Lib. Recall +1 Fx4 Lib+1 Recall
14 Effect-4 Lib. Recall –1 Fx4 Lib–1 Recall
15 Effect-4 Lib. Recall No.XX Fx4 LibXXX  RCL.
16 Effect-1 Bypass On/Off Fx1 Bypass 
17 Effect-2 Bypass On/Off Fx2 Bypass 
18 Effect-3 Bypass On/Off Fx3 Bypass
19 Effect-4 Bypass On/Off Fx4 Bypass
20 Channel Lib. Recall +1 CH Lib+1  Recall
21 Channel Lib. Recall –1 CH Lib–1  Recall
22 Channel Lib. Recall No. XX CH LibXXX Recall
23 GATE Lib. Recall +1 Gate Lib+1  RCL.
24 GATE Lib. Recall –1 Gate Lib–1  RCL.
25 GATE Lib. Recall No. XX Gate LibXXX RCL.
26 COMP Lib. Recall +1 Comp Lib+1  RCL.
27 COMP Lib. Recall –1 Comp Lib–1  RCL.
28 COMP Lib. Recall No. XX Comp LibXXX RCL.
29 EQ Lib. Recall +1 EQ Lib+1  Recall
30 EQ Lib. Recall –1 EQ Lib–1  Recall
31 EQ Lib. Recall No. XX EQ LibXXX Recall
32 Input Patch Lib. Recall +1 IN Patch Lib+1
33 Input Patch Lib. Recall –1 IN Patch Lib–1
34 Input Patch Lib. Recall No. XX IN Patch LibXX
35 Output Patch Lib. Recall +1 Out Patch Lib+1
36 Output Patch Lib. Recall –1 Out Patch Lib–1
37 Output Patch Lib. Recall No. XX Out Patch LibXX
38 Input Fader Group Enable A IN Fader Group A
39 Input Fader Group Enable B IN Fader Group B
40 Input Fader Group Enable C IN Fader Group C
41 Input Fader Group Enable D IN Fader Group D
42 Input Fader Group Enable E IN Fader Group E
43 Input Fader Group Enable F IN Fader Group F
44 Input Fader Group EnableG IN Fader Group G
45 Input Fader Group Enable H IN Fader Group H
46 Input MUTE Group Enable I IN Mute Group I
47 Input MUTE Group Enable J IN Mute Group J
48 Input MUTE Group Enable K IN Mute Group K
49 Input MUTE Group Enable L IN Mute Group L
50 Input MUTE Group Enable M IN Mute Group M
51 Input MUTE Group Enable N IN Mute Group N
52 Input MUTE Group Enable O IN Mute Group O
53 Input MUTE Group Enable P IN Mute Group P
54 Output Fader Group Enable Q OutFader Group Q
55 Output Fader Group Enable R OutFader Group R
56 Output Fader Group Enable S OutFader Group S
57 Output Fader Group Enable T OutFader Group T
58 Output MUTE Group Enable U Out Mute Group U
59 Output MUTE Group Enable V Out Mute Group V
60 Output MUTE Group Enable W Out Mute Group W
61 Output MUTE Group Enable X Out Mute Group X
62 Input Fader Group Assign X IN Fader Assign X
63 Input Mute Group Assign X IN Mute Assign X
64 Input EQ Group Assign X IN EQ Assign x
65 Input COMP Group Assign X IN COMP Assign x
66 Output Fader Group Assign X OutFader Assign X
67 Output Mute Group Assign X Out Mute Assign X
68 Output EQ Group Assign X Out EQ Assign x
69 Output COMP Group Assign X Out COMP Assign x
70 Input Mute Group Master X In Mute Master X
71 Output MUTE Group Master X Out Mute Master X
72 PEAK HOLD On/Off Peak Hold
73 OSCILLATOR On/Off OSC ON/OFF
74 SOLO Enable SOLO ENABLE
75FADER/SOLO RELEASE Mode 
On/OffFaderSolo RELEASE
76 Control Room Monitor MONO C-R MONO
77 Pan / Surround Link PAN/SURR LINK
78 Channel Name ID/Short CH ID/Short
79 Channel Copy Channel Copy
80 Channel Paste Channel Paste
81 Display Back Display Back
82 Display Forward Display Forward
83 UDEF KEYS BANK +1 UDEF KEYS BANK+1
84 UDEF KEYS BANK –1 UDEF KEYS BANK–1
85 UDEF KEYS BANK  X UDEF KEYS BANK x
86 REMOTE USER DEFINE BANK +1 RMT UDEF BANK+1
87 REMOTE USER DEFINE BANK –1 RMT UDEF BANK–1
88 REMOTE USER DEFINE BANK X RMT UDEF BANK X
89 REMOTE USER ASS LAYER BANK +1 USR LAYER BANK+1
90 REMOTE USER ASS LAYER BANK –1 USR LAYER BANK–1
91 REMOTE USER ASS LAYER BANK X USR LAYER BANK X
92 MIDI NOTE No.XX MIDI NOTE XXX
93 MIDI Program change No.XX MIDI PGM XXX
94 MIDI Control Change No.XX MIDI CC XXX
95 Machine REC Machine REC
96 Machine PLAY Machine PLAY
97 Machine STOP Machine STOP
98 Machine FF Machine FF
99 Machine REW Machine REW
100 Machine SHUTTLE Machine SHUTTLE
101 Machine SCRUB Machine SCRUB
102 Machine LOCATE X Machine LOCATE X
103 Machine Set LOCATE X Machine Capture X
104 Machine RTZ Machine RTZ
# Function Display 
						

							120Appendix: Parameter Lists
01V96i—Reference Manual
105 Machine Set RTZ Machine Set RTZ
106 Track Arming 1 Track Arming 1
107 Track Arming 2 Track Arming 2
108 Track Arming 3 Track Arming 3
109 Track Arming 4 Track Arming 4
110 Track Arming 5 Track Arming 5
111 Track Arming 6 Track Arming 6
112 Track Arming 7 Track Arming 7
113 Track Arming 8 Track Arming 8
114 Track Arming 9 Track Arming 9
115 Track Arming 10 Track Arming 10
116 Track Arming 11 Track Arming 11
117 Track Arming 12 Track Arming 12
118 Track Arming 13 Track Arming 13
119 Track Arming 14 Track Arming 14
120 Track Arming 15 Track Arming 15
121 Track Arming 16 Track Arming 16
122 Track Arming 17 Track Arming 17
123 Track Arming 18 Track Arming 18
124 Track Arming 19 Track Arming 19
125 Track Arming 20 Track Arming 20
126 Track Arming 21 Track Arming 21
127 Track Arming 22 Track Arming 22
128 Track Arming 23 Track Arming 23
129 Track Arming 24 Track Arming 24
130 Track Arming All Clear Track Arming CLR
131 DAW REC DAW REC
132 DAW PLAY DAW PLAY
133 DAW STOP DAW STOP
134 DAW FF DAW FF
135 DAW REW DAW REW
136 DAW SHUTTLE DAW SHUTTLE
137 DAW SCRUB DAW SCRUB
138 DAW AUDITION DAW AUDITION
139 DAW PRE DAW PRE
140 DAW IN DAW IN
141 DAW OUT DAW OUT
142 DAW POST DAW POST
143 DAW RTZ DAW RTZ
144 DAW END DAW END
145 DAW ONLINE DAW ONLINE
146 DAW LOOP DAW LOOP
147 DAW QUICKPUNCH DAW QUICKPUNCH
148 DAW GROUP STATUS DAW GROUP STATUS
149 DAW AUTO FADER DAW AUTO FADER
150 DAW AUTO MUTE DAW AUTO MUTE
151 DAW AUTO PAN DAW AUTO PAN
152 DAW AUTO SEND DAW AUTO SEND
153 DAW AUTO PLUGIN DAW AUTO PLUGIN
154 DAW AUTO SEND MUTE DAW AUTO SENDMUTE
155 DAW AUTO READ DAW AUTO READ
156 DAW AUTO TOUCH DAW AUTO TOUCH
157 DAW AUTO LATCH DAW AUTO LATCH
158 DAW AUTO WRITE DAW AUTO WRITE
159 DAW AUTO TRIM DAW AUTO TRIM
160 DAW AUTO OFF DAW AUTO OFF
161 DAW AUTO SUSPEND DAW AUTO SUSPEND
162 DAW AUTO STATUS DAW AUTO STATUS
163 DAW MONITOR STATUS DAW MONI STATUS
# Function Display
164 DAW CREATE GROUP DAW CREATE GROUP
165 DAW SUSPEND GROUP DAW SUSPEND GRP
166 DAW WINDOW TRANSPORT DAW WIN TRANSPORT
167 DAW WINDOW INSERT DAW WIN INSERT
168 DAW WINDOW MIX/EDIT DAW WIN MIX/EDIT
169 DAW WINDOW MEM-LOC DAW WIN MEM-LOC
170 DAW WINDOW STATUS DAW WIN STATUS
171 DAW Shortcut UNDO DAW UNDO
172 DAW Shortcut SAVE DAW SAVE
173 DAW Shortcut EDIT MODE DAW EDIT MODE
174 DAW Shortcut EDIT TOOL DAW EDIT TOOL
175 DAW Shortcut SHIFT/ADD DAW SHIFT/ADD
176 DAW Shortcut OPTION/ALL DAW OPTION/ALL
177 DAW Shortcut CTRL/CLUCH DAW CTRL/CLUCH
178 DAW Shortcut ALT/FINE DAW ALT/FINE
179 DAW BANK + DAW BANK +
180 DAW BANK – DAW BANK –
181 DAW Channel + DAW Channel +
182 DAW Channel – DAW Channel –
183 DAW REC/RDY X DAW REC/RDY X
184 DAW REC/RDY ALL DAW REC/RDY ALL
185Studio Manager Window Control 
CloseSM CTRL Close
186Studio Manager Window Control 
Close AllSM CTRL Close All
187Studio Manager Window Control 
Selected ChannelSM CTRL Sel Ch
188Studio Manager Window Control 
LibrarySM CTRL Library
189Studio Manager Window Control 
Patch EditorSM CTRL Patch
190Studio Manager Window Control 
Surround EditorSM CTRL Surround
191Studio Manager Window Control 
Effect EditorSM CTRL Effect
192Studio Manager Window Control 
MeterSM CTRL Meter
193Studio Manager Window Control 
LayerSM CTRL Layer
194Studio Manager Window Control 
MasterSM CTRL Master
# Function Display