Yamaha Dpx 1100 User Manual

							27
Menu
7
Color Adjustment 
(Input signal)
Video/S-Video/Component/
RGB TV/RGB PC
Adjusts color balance.
There are three menus available, [Standard], [WRGB], and [WRGBYCM], separated in order
of complexity from simple to detailed. Refer to page 36 for parameter operation methods.
The present color temperature setting is displayed to the right of the menu items.
- Standard
Adjusts color temperature and hUV only.
hUV adjusts values within the maximum
color temperature limits of the projector.
- WRGB
Adjusts the color coordinates and gain for
the three primary colors, R(Red), G(Green),
and B(Blue). The unit sets the complemental
colors Y(Yellow), C(Cyan), and M(Magenta)
automatically. Adjusting [Color Temp.] resets
the RGB gain based on color coordinate
settings. Adjusting [Gain] resets [Color temp.]
based on color coordinate settings.
- WRGBYCM
Adjusts the color coordinates and gain for
each component color individually. Press
the RESET button on the remote control
when the WRGBYCM menu is open to
automatically adjust the RGB gain and
YCM color coordinates and gain based on
the color temperature and RGB color
settings. When you have selected
WRGBYCM in the color adjustment
submenu, press RESET to automatically
adjust the RGB gain and YCM color
balance to the most appropriate setting,
based on color temp and RGB color
balance settings.
Choices: White correction : -0.02 to +0.02
Color temperature : 5,000 to 10,000
Gain : 0.00 to 1.99
Iris 
(Input signal)
Video/S-Video/Component/RGB TV/RGB PC
Adjusts the iris (Optical).
You can select 3 levels.
Menu items
Color AdjustmentStandard
6700K +
0.000uv-The current color temperature is displayed.
Level Adjustment 
(Input signal)
Component/RGB TV/RGB PC
Adjusts the analog input signal gain and offset settings.
Adjust the gain and offset for component and RGB (Y, C
B, CR/R, G, B) input signals.
Choices: -50 to 0 to +50 (except for HDMI signals)
White PeakingEnhances the brilliance of the white portions of the projected image.
Choices:  0 to 5
y
0.5
0.0
0.0 0.5 x
W (Color temperature
and h UV)
y
0.5
0.0
0.0 0.5 x
W (Color temperature
and h UV)
G (Green)
R (Red)
B (Blue)
y
0.5
0.0
0.0 0.5 x
W (Color temperature
and h UV)
Y (Yelow)
R (Red)
B (Blue) M (Magenta) G (Green)
C (Cyan)
Open Close
13_DPX-1100_E.p652004.04.16, 12:57 27 
						

							28
Menu items

 Signal
You can adjust the image when the unit is receiving an input signal.
Display Aspect Ratio
(Input signal)
Video/S-Video/Component/RGB TV/RGB PC
Sets the aspect ratio for projecting an image from an input signal.
See “Selecting a display aspect for projecting images”, page 17.
Overscan 
(Input signal)
Video/S-Video/Component/RGB TV
Overscans video input sources for display.
Selects from [Standard] and [Full].  This parameter is not available when you select [Smart
Zoom] in [Display Aspect]. In some cases, noise may appear at the edges of the image
when you select [Full].
•The overscan for [Standard] mode is approximately 94%.
•The overscan for [Full] mode is approximately 100%.
3D Y/C  Separation 
(Input signal)
Video(NTSC)
Adjusts the quality of images input from VIDEO jack.
Suppresses the rainbow-like color and annoying dots in images. This function is only
available for NTSC format signals the unit receives at its composite input jacks.
Choices: On/Off
Noise Reduction 
(Input signal)
Video/S-Video/Component/RGB TV
Reduces noise in analog images.
Digital processing eliminates noise in the luminance and color signals from sources with a
comparatively large amount of noise, producing a more vivid image. Use when the quality
of the source you are viewing requires it.
Choices: Off/1/2/3
Progressive Mode 
(Input signal)
Video/S-Video/Component/RGB TV
Switches the interlace/progressive (I/P) conversion mode.
Changes from Interlace/Progressive (I/P) conversion mode to [Auto] or [Video] mode.
(Only for SDTV interlaced signal).
•[Auto] : Detects the film source automatically and projects it progressively.
•[Video] : Turns the detection function off.
Video Type 
(Input signal)
Video/S-Video
Selects the correct type of device to ensure image synchronization.
Select [VCR] when using an analog video tape as a video source. Select [DVD] for other
sources.
Color Space Conversion
(Input signal)
Video/S-Video/Component
Selects color space coefficients.
•[Auto] : Selects the best color space coefficient for the image resolution.
•[SDTV] : Color space coefficient for BT.601 type signal.
•[HDTV] : Color space coefficient for BT.709 type signal.
Setup Level (SDTV)
(Input signal)
Video/S-Video/Component/RGB TV
Compensates for differences in the black levels of SDTV images.
•For signals equal to the pedestal level : Set to [0%].
•For signals with high levels of blackness : Set to [7.5%].
100
0 %
PEDESTAL LEVEL BLACK LEVEL
13_DPX-1100_E.p652004.04.16, 12:57 28 
						

							29
Menu
7
Menu items
Setup Level (HDTV)
(Input signal)
Component/RGB TV
Compensates for differences in the black levels of HDTV images.
Usually, choose [0%].
•For signals equal to the pedestal level : Set to [0%].
•For signals with high levels of blackness : Set to [7.5%].
Clamp Position 
(Input signal)
Component/RGB TV
Adjusts the clamp position for analog video sources.
Choices: -30 to +30
Horiz. Display Position
(Input signal)
RGB PC (except for HDMI signals)/
Component/RGB TV
Adjusts the horizontal display position of the image.
Choices: PC type : -50 to 0 to +50
Video type : -10 to 0 to +10
Vert. Display Position
 
(Input signal)
RGB PC (except for HDMI signals)/
Component/RGB TV
Adjusts the vertical display position of the image.
Choices: PC type : -50 to 0 to +50
Video type : -5 to 0 to +5
Signal StatusDisplays the resolution of the image signal the unit is receiving.
Sync signal information for RGB type inputs is also displayed.
100
0 %
PEDESTAL LEVEL BLACK LEVEL
Sync Adjustment 
(Input signal)
RGB PC (except for HDMI signals)
Regulates flickering, noise, and disorder in the image.
Choices: -128 to +127
Tracking 
(Input signal)
RGB PC (except for HDMI signals)
Regulates vertical striping in the image.
Choices: 0 to 31
13_DPX-1100_E.p652004.04.16, 12:58 29 
						

							30

 Initial
Menu items
Color SystemSelects the color system to use for video input signals.
Usually, set this parameter to Auto to have the unit automatically detect the signal and
select an appropriate color system. Set the unit manually to view NTSC4.43 images as it
cannot detect NTSC4.43 automatically.
Choices: Auto/NTSC/NTSC4.43/PAL/PAL-M/PAL-N/PAL60/SECAM
INPUT A Sync Type Selects the sync type for signals received at INPUT A.
This function is only available for RGB TV.
Choices: Auto/Separate Sync/Composite Sync/Sync on Green
INPUT A SignalSelects the type of input signal received at INPUT A.
Choices: Component/RGB PC/RGB TV
INPUT B Sync Type Selects the sync type for signals received at INPUT B.
This function is only available for RGB TV.
Choices: Auto/Separate Sync/Composite Sync/Sync on Green
HDMI SignalSelects the signal type received at the HDMI jack.
Choices: Auto/Component/RGB TV
Auto Input Search Automatically changes inputs when the unit does not receive a signal.
If the signal the unit is currently receiving stops,  or the input signal you selected the last
time you used the unit does is not available when you turn the unit power on, it
automatically searches through inputs for a signal in the following order.
 INPUT A 
 INPUT B  D4 VIDEO  S VIDEO  VIDEO  HDMI
 INPUT A
Choices: On/Off
Display LanguageSelects the language used in the menu display.
Choices: 
/English/Deutsch/Español/Français/Italiano/Portuguêsa//
ResetResets menu parameters to their default setting.
Resets all menu parameters to their default setting, and return the configurations stored in
the memory to their defaults. See page 37, 44 and 45 for the operational procedure.
• [All Settings] : Return all settings in the [Initial] and [Setup] menu groups in the
main menu, and all configurations stored by the memory function, to
their factory default settings.
• [All Memory] : Return all configurations stored by the memory function to their
factory default settings.
• [Current Memory] : Return the currently selected memory configuration to its factory
default setting.
Lamp Running TimeDisplays the total lamp running time.
Opens the submenu to reset the running time. See page 38 for the operational procedure.
INPUT B SignalSelects the signal type received at INPUT B.
Choices: Component/RGB PC/RGB TV
Auto Power Off If the signal the unit is currently receiving stops and you do not perform any
operations for 30 minutes or more, the unit automatically places itself in
standby mode.
Choices: On/Off
13_DPX-1100_E.p652004.04.16, 12:58 30 
						

							31
Menu
7
Menu items

 Setup
LocationDesignate the location of the main unit.
Choices: [Front/Table] [Front/Ceiling] [Rear/Table] [Rear/Ceiling] ( page 48)
Keystone CorrectionAdjusts the projection angle of the image.
If you do not install the projector at right angles to the screen, the image will be trapezoidally
distorted. You can electronically correct this distortion using the keystone function to adjust the
width without changing the height of the image. Increase the keystone value (0 to 100) when the
top of the image is overly wide, and reduce it (-100 to 0) when the lower part is overly wide.
Remote Control SensorSets the remote control sensor.
The main unit has two remote control sensors, one on the front panel and one on the rear,
which this setting allows you to switch between.  The remote control functions regardless
of the setting of this parameter if you use a wired connection to connect it to the main unit.
Choices: Front & Rear/Front/Rear/Off
Remote Control ID Sets the remote control ID.
The main unit can receive commands from the remote control if you set the same ID in the main
menu as the remote control code switch on the side of the remote control is set to. Use this remote
control code switch to allow one remote control to control two main units independently.
Choices: ID1/ID2
Lamp Power Lowers the power supply to the lamp.
You can adjust the power supplied to the lamp within the range of 80 to 100%.
Lens Adjustment LockLocks the lens adjustment function.
Locks the lens so that you cannot change the V.POS, ZOOM, and FOCUS settings
accidentally when set to [ON]. Set to [OFF] to cancel this function.
Menu Color
Trigger Out Sets the TRIGGER OUT terminal.
Set the external control TRIGGER OUT jack 12 V signal emission to [Lamp] to
synchronize it to the ON/OFF state of the lamp, to [Fan] to synchronize it to the fan, and to
[RS-232C] to receive ON/OFF signals through the RS-232C terminal.
Choices: Lamp/Fan/RS-232C
Menu ModeSwitches menu modes between an easy-to-use basic mode and a detailed
advanced mode.
Choices: Basic/Advanced
Baud Rate Sets the transmission speed of the RS-232C terminal.
This setting becomes valid from the next time you switch the unit on.
Choices: 9600bps/19200bps/38400bps/57600bps/115200bps
Message Selects whether to display memory number, input signal and other
information on the projection screen. ( page 58)
Choices: On/Off
When the upper part of
the image is wider than the lower
Increase the value
in the positive (+) direction
Decrease the value
in the negative (-) directionWhen the lower part of
the image is wider than the top
Selects the color of the letters and background the main unit uses to display
the menu on screen.
You can choose to display the menu screen in [Monotone] or [Color]. Also, you can adjust
the contrast and brightness of the menu from the [Menu Brightness] and [Menu Contrast]
menus. You can select from 3 color types.
Monotone Menu Brightness
Menu ContrastColor Menu Brightness
Menu Contrast
Color Style
13_DPX-1100_E.p652004.04.16, 12:58 31 
						

							32
Menu operations

Operation button functions
Use the buttons on the remote control or the main unit to operate the menus. The button functions are listed below.
1Menu Button
Opens/Closes the menu.
2Cursor button
+ / - (Move the cursor ringht/left)
•Selects menu groups.
•Opens/Closes submenus.
•Selects/Changes settings.
h / g (Moves the cursor up/down)
•Selects menu items.
•Selects/Changes settings.
3 button
•Confirms setting changes.
•Opens the in-line menu when the menu is not open.
•Selects special menu items ( page 36) and memory operation. ( page 41)
4ESCAPE button
•Returns the cursor one level up the menu (e.g. From the menu item level to the menu
group level).
•Closes submenus.
•Closes the menu screen when the cursor is in a menu group.
•Returns from the menu movement bar to the menu entry screen, after moving a menu.
5RESET button (Remote control only)
Returns parameters back to their default settings (Does not affect items with no default
setting).
45
RESET
6 123
VIDEO STILLHIDE
PATT IRIS AUTOSETTING
ZOOM FOCUS V. POS
LIGHT
BD4
S VIDEOA
INPUT
MEMORY
HDMI
INPUT
MENU
ASPECT
ESCAPE
STANDBY/ON
SETTING
LAMP COVER TEMP FAN PATTERN
ESCAPEMENU
INPUT ASPECT
3 1
2 4
5
1
3 4
2
Remote Control
Main Unit
13_DPX-1100_E.p652004.04.16, 12:58 32 
						

							33
Menu
7
Menu operations

Menu operations 1 (with no submenu)
Menu operations use the procedure below to adjust menu item without submenus.
1. Open the menu screen.
Press the MENU button to open the menu
screen.
Memo
•If you have opened the menu screen
previously, the menu displays the
settings from the last time you used it.
2. Select a menu group.
Use the +/- buttons to select a menu group.
The illustration at right depicts the [Setup]
group being selected.
Menu items related to the selected menu group are displayed.
You can now adjust the selected item.
Select a menu group (Image / Signal / Initial / Setup)
(Select with the +/- buttons)
Select an item to adjust or a setting
(Select with the h / g buttons)
Choose a setting for the selected item
(Usually, use the +/- buttons)
Remote Control Main Unitor
Image
Black Level
OffLMLMHH
abcde
Memory 1VIDEO 0
White Level 0Gamma TrimHue 0Saturation 100Sharpness TypeSharpness GainColor Adjustment
Level AdjustmentIris
SignalInitialSetup
4
White PeakingMove Menu WindowWRGB
06500K +
0.000uv-
Location
VIDEO
Keystone Correction 0Remote Control SensorRemote Control IDLens Adjustment Lock
Menu Color
OffOnLamp Power 105
BasicAdvanceOffOnMessageTrigger OutBaud Rate
Front / Table
Front & Rear
Monotone
Lamp115200bps
ID 1
Menu Mode
Image
Memory 1 Signal Initial SetupMove Menu Window
STANDBY/ON
SETTING
LAMP COVER TEMP FAN PATTERN
ESCAPE MENU
INPUT ASPECTPATT IRIS AUTOSETTINGZOOM FOCUS V. POS
INPUT
MENU
ASPECT
ESCAPE
Remote Control Main Unit
MENU Button
13_DPX-1100_E.p652004.04.16, 12:58 33 
						

							34
6. Close the menu screen.
When you have finished making
adjustments, press the MENU button to
close the menu screen. 5. Move to another item or group.
Memo
•Use the h / g buttons to move the
cursor to another item in the same
group.
To move to an item in another menu
group, press ESCAPE or the h button
to return to the top of the menu group,
and repeat steps 2,3 and 4. Remote Control Main Unitor
Menu operations
4. Choose a setting for the item.
Use the +/- buttons to select a suitable
setting.
The illustration at right depicts the  [Lens
Adjustment Lock] mode set to [On].
Memo
•The setting method depends on the
item selected. In the example at right,
press +/- buttons to change On/Off
states of the menu item.
3. Select a menu item.
Use the h / g buttons to move the cursor to
the item you wish to adjust.
The illustration at right depicts [Lens
Adjustment Lock] being selected.
Remote Control Main Unitor
Remote Control Main Unitor
VIDEO
0
105
Location
Keystone Correction
Remote Control Sensor
Remote Control ID
Lens Adjustment Lock
Menu ColorOffOn
Lamp Power
BasicAdvance
OffOn Message
Trigger Out
Baud RateFront / Table
Front & Rear
Color
Lamp
115200bps ID 1
Menu ModeImage
Memory 1 Signal Initial SetupMove Menu Window
VIDEO
0
105
Location
Keystone Correction
Remote Control Sensor
Remote Control ID
Lens Adjustment Lock
Menu ColorOffOn
Lamp Power
BasicAdvance
OffOn Message
Trigger Out
Baud RateFront / Table
Front & Rear
Monotone
Lamp
115200bps ID 1
Menu ModeImage
Memory 1 Signal Initial SetupMove Menu Window
Remote Control Main Unit
STANDBY/ON
SETTING
LAMP COVER TEMP FAN PATTERN
ESCAPE MENU
INPUT ASPECTPATT IRIS AUTOSETTINGZOOM FOCUS V. POS
INPUT
MENU
ASPECT
ESCAPE
Remote Control Main Unit ESCAPE Button
STANDBY/ON
SETTING
LAMP COVER TEMP FAN PATTERN
ESCAPE MENU
INPUT ASPECTPATT IRIS AUTOSETTINGZOOM FOCUS V. POS
INPUT
MENU
ASPECT
ESCAPE
MENU Button
13_DPX-1100_E.p652004.04.16, 12:58 34 
						

							35
Menu
7
Menu operations

Menu operations 2 (with submenus)
Use the procedure below to adjust menu items that contain submenus.
1. Select a menu item.
Carry out steps 1-3 of “Menu Operations 1”
to select the item you want to set.
The illustration at right depicts [Display
Language] in the [Initial] group selected.
Memo
•A  appears to the right of items that
contain a submenu.
Remote Control Main Unitor
Color System
VIDEO
INPUT A SignalINPUT A Sync TypeINPUT B SignalINPUT B Sync Type
Auto Power OffAuto Input SearchDisplay Language
Reset
AutoComponentAutoRGB TVAutoHDMI SignalComponent
EnglishLamp Running Time0 Hour
On OffOffOn Image
Memory 1 Signal Initial SetupMove Menu Window
ItalianoPortuguêsa
FrançaisEspañolDeutschEnglish
VIDEO Display Language Image
Memory 1 Signal Initial SetupMove Menu Window
VIDEO
ItalianoPortuguêsa
FrançaisEspañolDeutschEnglish
2. Use the + buttons to move to the
submenu.
Memo
•Some menu items contain other items
that you can select. In such cases,
move to the lower level sub-menu
using the + button.
3. Use the cursor button to adjust
item settings.
Memo
•You must press the  button to
confirm some settings.
 : Fix appears in the operations
guide at the bottom left of the menu
screen if this is necessary.
4. Press the – or ESCAPE buttons
to return to higher level menu
items.
5. Close the menu screen.
Press the MENU button to close the menu
screen when you have finished making
adjustments. Items using the 
 button for setting.
Display Aspect Ratio
Color System
Input A Signal
Input A Sync Type
Input B Signal
Input B Sync Type
HDMI Signal
Remote Control Sensor
Remote Control ID
13_DPX-1100_E.p652004.04.16, 12:59 35 
						

							36 

Special menu operations
Some items in the menu require special methods to configure.
VIDEOMemory 1 Initial Setup
nu Window
Gain 0.82
y
0.3 0.35
0.6 0.65x
x=0.640     y=0.330
Image SignalMove Me
n
: Edit
y
0.5
0.0
0.0 0.5 x
Red
Example: Adjusting R (Red)
The name of the
selected item appears
here.
Use the cursor buttons
to select an item.Press the 
 button.
Press the ESCAPE
button.Color coordinate
display area
Color coordinate
adjustment area
Press the  button to
change the item to adjust.
Gain setting
display areaGain adjustment
area
Menu operations
1. Select [Color Adjustment] in the [Image] group from the main menu.
2. Press the + button to enter submenus.
3. Select a suitable item from [Standard] • [WRGB] • [WRGBYCM] using the h or g buttons, and
press the + button.
This explanation uses the [WRGBYCM] menu as an example.
4. Use the cursor buttons to select the item you wish to configure from the color scale and press
the 
 button.
Color coodinate adjustment area on the right side of the menu screen will be highlighted.
5. Use the cursor buttons to adjust a setting for the item.
6. Press the 
 button to move to the gain adjustment area for R (red), G (green), B (blue), Y
(yellow), C (cyan), and M (magenta).
7. Press the +/- buttons to adjust the gain.
8. Press the ESCAPE button to return to the color scale.
Memo
 •See page 27 for datails about each color item.
13_DPX-1100_E.p652004.04.16, 12:59 36