Yamaha Dtxpress 3 Manual

31
Utility Mode
2-5.  Factory Set
This function replaces all internal settings in the DTXPRESS III
to their factory-set condition.
The Factory Set function will replace all internal set-
tings in the DTXPRESS III to their factory-set con-
dition. Take care so as not to loose important data.
Make sure any settings and user songs you want to
keep have been saved to an external device such as
the Yamaha MIDI Data Filer MDF3, etc. (m[3-1.
Bulk Dump] (P. 31)
Procedure
1.Enter the display shown above, press...

32
Utility Mode
2.Select the type of bulk data (that will be sent) in the dis-
play shown above and press the [SAVE/ENT] button.
The display shown below will appear.3-2.  Channel 10 Program Change/Channel Event Receive
This enables or disables the DTXPRESS III to receive program
change messages/channel events through MIDI channel 10. Pro-
gram change messages received or transmitted through channel
10 can be used to switch DTXPRESS III drum kits.
It is necessary to set the receive parameter to “on” in...

33
Utility Mode
3-4.  Program Change Table
Use this function to create a program change table (a list of pro-
gram change numbers that correspond to drum kits).
A program change message received internally from the
DTXPRESS III or through channel 10 from an external MIDI de-
vice will select, according to the program change table, the drum
kit corresponding to the kit number in the DTXPRESS III.
3-6.  Device Number, Local Control
Sets the MIDI device number and local control.
q No (Program Change...

34
Utility Mode
3-8.  Dump Interval
This sets the length of intervals between the packets of MIDI data
sent by the DTXPRESS III Bulk Out function. The intervals can
be adjusted to the capacity of the external receiving MIDI device
to prevent data overflow.
q DumpInterval (Dump Interval)
 [Range] 50, 100, 150, 200, 250, 300 (in msec.)
3-9.  Send Hi-Hat Control
This sets whether or not hi-hat controller events will be transmit-
ted from the MIDI OUT jack or TO HOST jack.
q Send HH Ctrl (Send Hi-Hat...

35
Utility Mode
q
UT CLK Click= hi
Vol=127  Tu=+0.0
we
q
UT CLK Click= hi
Note#= 22 (A#-1)
w
q
UT CLK SETUP
ClickMode=manual
q If this parameter is set to “0”, “NoAssign” will appear on the
display and sound will not be produced.
* Since sustained sounds cannot be used as a click voice, they
are not displayed.
* Refer to the [Drum Voice List] (P. 40).
4-3.  Click Volume, Tuning
This sets volume and pitch for each of the 3 Click Voices.
q Click (Click Voice)
Selects the Click Voice. (The same Click Voice...

36
UT SEQ SETUP
Count Switch=off
q
5-3.  Sync Mode
This function synchronizes the DTXPRESS III sequencer’s clock
with the clock of an external device.
5. SEQ (Sequencer) Group
This sub-mode contains settings that relate to the sequencer (song).
This group is divided into the following 4 pages.
5-1. MIDI Control .................................................... 36
5-2. Count Switch ................................................... 36
5-3. Sync Mode...

37
6.  MAP (Drum Map) Group
This sub-mode is used to edit the User Drum Map. This mode is
divided into the following 9 pages.
6-1. Voice ................................................................ 37
6-2. Volume, Pan .................................................... 37
6-3. Tuning .............................................................. 37
6-4. Layer Balance .................................................. 38
6-5. Decay, Cutoff Frequency ................................. 38
6-6. Reverb...

38
q N (MIDI Note Number)
Sets the MIDI note number (The same procedure as in [6-1. Voice]).
w Reverb send (Reverb Send Level)
[Range] 0-127
6-7.  Alternate Group, Key Assign Mode
This sets the Alternate Group and Key Assign Mode for each drum
voice w assigned to each MIDI note number q.
The function and setting of the Alternate Group, Key Assign
Mode are the same functions and settings found in [2-3. Alter-
nate Group, Key Assign Mode] (P. 20) in the Drum Kit Voice Edit
Mode.
q N (MIDI Note Number)...

39
Utility Mode
6-9.  Map Copy
This function copies the preset drum map’s entire internal settings
to a user drum map.
When the Map Copy function is used, the user drum
map’s internal settings will be erased and replaced
with the settings of the copy source. If you want to
keep important user drum map settings, use the bulk
dump operation and save the settings to an external
device before executing the map copy.
q from (Preset Drum Map)
Selects the preset drum kit number (1-48) that will be the copy...

40