2012 Na Yamaha Super Tenere Manual

haha 2
SPECIFICATIONS
GENERAL SPECIFICATIONS ........................................................................ 2-1
ENGINE SPECIFICATIONS ............................................................................ 2-2
CHASSIS SPECIFICATIONS ........................................................................ 2-10
ELECTRICAL SPECIFICATIONS ................................................................. 2-13
TIGHTENING TORQUES...

haha GENERAL SPECIFICATIONS
2-1
EAS20280
GENERAL SPECIFICATIONS
Model Model 23P4 (USA)
23P5 (California)
Dimensions Overall length 2255 mm (88.8 in)
Overall width 980 mm (38.6 in)
Overall height 1410 mm (55.5 in)
Seat height 845 mm (33.3 in) (low position)
870 mm (34.3 in) (high position)
Wheelbase 1540 mm (60.6 in)
Ground clearance 205 mm (8.07 in)
Minimum turning radius 2700 mm (106.3 in)
Weight Curb weight 261 kg (575 lb) (USA)
262 kg (578 lb) (California)
Maximum load (total weight of rider,...

haha ENGINE SPECIFICATIONS
2-2
EAS20290
ENGINE SPECIFICATIONS
Engine Engine type Liquid cooled 4-stroke, DOHC
Displacement 1199 cm³
Cylinder arrangement Inline 2-cylinder
Bore  × stroke 98.0 × 79.5 mm (3.86  × 3.13 in)
Compression ratio 11.00 :1
Standard compression pressure (at sea level) 680 kPa/250 r/min (6.8 kgf/cm ²/250 r/min, 96.7 
psi/250 r/min)
Minimum –maximum 590– 760 kPa (5.9–7.6 kgf/cm², 83.9 –108.1 psi)
Starting system Electric starter
Fuel
Recommended fuel Premium unleaded gasoline only...

haha ENGINE SPECIFICATIONS
2-3
Oil-pump-housing-to-inner-and-outer-rotor  clearance (scavenging pump) 0.06– 0.13 mm (0.0024–0.0051 in)
Limit 0.20 mm (0.0079 in)
Relief valve operating pressure 540.0–660.0 kPa (5.40– 6.60 kgf/cm², 78.3 –95.7 
psi)
Cooling system Radiator capacity (including all routes) 1.83 L (1.93 US qt, 1.61 Imp.qt)
Coolant reservoir capacity (up to the maximum level mark) 0.26 L (0.27 US qt, 0.23 Imp.qt)
Radiator cap opening pressure 93.3 –122.7 kPa (0.93– 1.23 kgf/cm², 13.5 –17.8...

haha ENGINE SPECIFICATIONS
2-4
Limit 29.850 mm (1.1752 in)
Camshaft runout limit 0.030 mm (0.0012 in)
Timing chain Tensioning system Automatic
Valve, valve seat, valve guideValve clearance (cold) Intake 0.10–0.16 mm (0.0039 –0.0063 in)
Exhaust 0.22–0.28 mm (0.0087 –0.0110 in)
Valve dimensions Valve head diameter A (intake) 36.90– 37.10 mm (1.4528–1.4606 in)
Valve head diameter A (exhaust) 30.90 –31.10 mm (1.2165– 1.2244 in)
Valve face width B (intake) 2.050 –2.480 mm (0.0807– 0.0976 in)
Valve face width...

haha ENGINE SPECIFICATIONS
2-5
Valve stem diameter (exhaust) 5.460–5.475 mm (0.2150– 0.2156 in)
Limit 5.430 mm (0.2138 in)
Valve guide inside diameter (intake) 5.500–5.512 mm (0.2165– 0.2170 in)
Limit 5.550 mm (0.2185 in)
Valve guide inside diameter (exhaust) 5.500–5.512 mm (0.2165– 0.2170 in)
Limit 5.550 mm (0.2185 in)
Valve-stem-to-valve-guide clearance (intake) 0.010 –0.037 mm (0.0004– 0.0015 in)
Limit 0.080 mm (0.0032 in)
Valve-stem-to-valve-guide clearance (exhaust) 0.025 –0.052 mm (0.0010– 0.0020...

haha ENGINE SPECIFICATIONS
2-6
Diameter D 97.965–97.980 mm (3.8569 –3.8575 in)
Height H 8.0 mm (0.31 in)
Offset 0.50 mm (0.0197 in)
Offset direction Intake side
Piston pin bore inside diameter 22.004 –22.015 mm (0.8663 –0.8667 in)
Limit 22.045 mm (0.8679 in)
Piston pin outside diameter 21.991 –22.000 mm (0.8658 –0.8661 in)
Limit 21.971 mm (0.8650 in)
Piston-pin-to-piston-pin-bore clearance 0.004 –0.024 mm (0.00016 –0.00094 in)
Piston ring
Top ring Ring type Barrel
Dimensions (B ×  T) 1.20 × 3.45 mm...

haha ENGINE SPECIFICATIONS
2-7
Crankshaft Width A 165.60–166.40 mm (6.520– 6.551 in)
Width B 67.75–68.25 mm (2.67 –2.69 in)
Runout limit C 0.020 mm (0.0008 in)
Big end side clearance D 0.160 –0.262 mm (0.0063– 0.0103 in)
Journal oil clearance 0.020 –0.044 mm (0.0008– 0.0017 in)
Bearing color code 1.Blue 2.Black 3.Brown 4.Green 5.Yellow
Balancer Balancer drive method Gear
Balancer shaft-journal-to-balancer shaft-journal-bearing clearance 0.016– 0.040 mm (0.0006–0.0016 in)
Clutch
Clutch type Wet,...

haha ENGINE SPECIFICATIONS
2-8
5th 1.042 (25/24)
6th 0.929 (26/28)
Main axle runout limit 0.08 mm (0.0032 in)
Drive axle runout limit 0.08 mm (0.0032 in)
Shifting mechanism
Shift mechanism type Shift drum and guide bar
Shift fork guide bar bending limit 0.100 mm (0.0039 in)
Shift fork thickness 6.26 –6.39 mm (0.2465 –0.2516 in)
Air filter
Air filter element Oil-coated paper element
Fuel pumpPump type Electrical
Output pressure 324.0 kPa (3.24 kgf/cm ², 47.0 psi)
Fuel injector
Model/quantity 297500–...

haha ENGINE SPECIFICATIONS
2-9
Ring-gear-to-thrust-washer clearance 0.10–0.20 mm (0.004 –0.008 in)
Final gear backlash 0.20–0.40 mm (0.008 –0.016 in)