AllTrade Kawasaki 192V Cordless Circular Saw 840056 User Manual

							OPERATING THE RECIPROCATING SAW
Never tape the trigger switch down to provide continuous
high speed.The tool may fail under such conditions causing fire or personal
injury.
The lock-off button helps prevent accidental starting.
This button can be pressed from either side.VARIABLE SPEED TRIGGER SWITCH
THIS TOOL IS CONTROLLED 
BY A TRIGGER SWITCH:
• The speed of the Cordless Reciprocating Saw depends on the amount of pres-
sure applied on the trigger. The further the trigger is pressed, the faster the tool
will go.
• Press the lock-off button, then pull the “ON/OFF”trigger to turn the Cordless
Reciprocating Saw“ON”. To turn the Cordless Reciprocating Saw “OFF”, 
release the trigger switch. 
14
ATTACHING / REMOVING BLADE
Failure to remove the battery pack from the saw before
removing the blade could result in accidental starting and serious personal
injury.
• Remove the battery pack.
• Use the allen wrench to loosen the blade clamp screw on the side of the saw by
turning it counter-clockwise. Do not remove the screw entirely.
TO ATTACH BLADE:
• Press the hole in the shank of the blade onto the pin in the saw bar. Make sure
that the teeth of the blade are facing downward.
• Tighten the blade clamp screw 
back into place. 
• Remove allen wrench.
• Replace the battery pack.
TO REMOVE BLADE:
• Pull the hole in the shank of the blade off the pin in the saw bar.
• Tighten the blade clamp screw back into place. 
• Remove allen wrench.
• Replace the battery pack.
13
TRIGGER
SWITCH
LOCK-ON
BUTTON
BLADE CLAMP 
						

							PLUNGE CUTTING
Never feed the blade into the work piece until the blade
is at full speed. If the blade is not at full speed, the saw may kick back 
causing serious personal injury. 
• Mark out the line to be cut so it is easily visible.
• Start inside the area to be cut out.
• Depress the lock-on button and press the trigger 
to start the saw.
• Set the shoe against the work piece.
• When the blade reaches full speed, slowly feed the blade into the work piece.
16
GENERAL CUTTING
Always hold the saw in front of you and away from your body. Keep your
hands and feet well away from the work piece. 
Never feed the blade into the work piece until the blade is at full speed. 
If the blade is not at full speed, the saw may kick back causing serious 
personal injury. 
Use proper blade for the particular cutting application.
• Put on eye protection.
• Clear the saw of any 
foreign material.
• Make sure the work piece is held
securely in place. Hold smaller
pieces in a vise or attach to the
workbench with clamps.
• Mark out the line to be cut so it is easily visible.
• Pull the trigger to start the saw.
• Set the shoe against the work piece.
• When the blade reaches full speed, slowly feed the blade into the work piece.
15 
						

							MAINTENANCE AND CLEANING
Always remove the battery pack before attempting
cleaning or maintenance.
This Cordless Reciprocating Saw is lubricated before 
it leaves the factory. This lubrication should last for the life of the tool. No 
further lubrication is required.
Use only mild soap and a damp cloth to clean the tool.Never let any liquid get
inside the casing. Never immerse any part of the tool in a liquid. Always keep the
ventilation openings clear.
Always clean the battery pack using only a dry cloth. Do not use liquids. 
Always unplug the charger before cleaning it.
Regularly clean the ventilation slots in your tool and charger using only a soft
brush or dry cloth.
Inspect all mounting screws regularly. Tighten any loose screws. Failure to keep
the mounting screws tight could result in serious injuries.
Never open the Cordless Reciprocating Saw case, battery pack or charger.Do not
attempt to repair the Cordless Reciprocating Saw, battery pack or charger yourself.
Opening any of these parts will void your warranty.
ACCESSORIES
Use only accessories that are recommended by the manufacturer for your model.
Accessories that may be suitable for one tool may become hazardous when used on
another tool.
Always attach grounded (3-prong) extension cords to grounded (3-hole) outlets.
If you must use an extension cord, be sure that the gauge is large enough to carry
the amount of current necessary for your power tool.If not, your tool may experi-
ence a loss of power, excessive voltage drop or overheating. The smaller the gauge
number, the heavier the cord (see table on the next page).
18
METAL CUTTING
Never use gasoline or any flammable liquid as a 
lubricant. Sparking from the motor may cause it to ignite into flames.
• When cutting metals other then copper, brass or aluminum, always use a lubricant,
such as cutting oil, to keep the blade cool. This will prolong the life of the blade as
well as speeding up the cutting process.
• Make sure the work piece is held securely in place. Hold smaller pieces, such as
pipe or conduit, in a vise or attach to the workbench with clamps.
• To eliminate vibration, always cut close to the clamping point.
• When cutting thin sheets of metal, place a piece of plywood on either side to control
vibration and prevent tearing.
17
OIL 
						

							OTHER CONSUMER DO-IT-YOURSELF (DIY) TOOLS
Alltrade offers a full range of Kawasaki™ tools that make DIY jobs easy. If you would
like further information on the following products, please contact Alltrade Customer
Service Department at 1-800-590-3723. 
Cordless Drills/Screwdrivers
Impact Wrenches
Sanders
Jigsaws
Circular Saws
Angle Grinders
Reciprocating Saws
Routers
Rotary Tools
Corded and Cordless Multi-Purpose Tools
Wide Range of Accessories and more. 
20
RECOMMENDED SIZES OF EXTENSION CORDS 120 VOLT AC 60 HZ TOOLSTOOL CURRENT RATING CONDUCTOR SIZE IN A.W.G
AMPERE 10FT. 25FT. 50FT. 100FT.
3-6 18 18 18 186-8 18 18 18 168-10 18 18 18 1410-12 16 16 14 1412-16 14 12 12 -16-20 12 12 12 -
SPECIFICATIONS
SPECIFICATIONS
Voltage 19.2V Length of Stroke 22mm (7/8)Switch Variable Speed with BrakeCharger Input 120V  60HzCharging Time Approx. 3-5 hoursNo Load Speed (RPM) 0-2600/minBattery Type Ni-Cad
PROTECTING THE ENVIRONMENT
BATTERIES
Alltrade batteries can be recharged many times. At the end of their useful life, recy-
cle batteries with due care for our environment. 
Ni-Cad and Ni-MH batteries are recyclable. Take them to your local recycling center
or call 1-800-822-8837. Collected batteries will be recycled or disposed of properly.
19 
						

							item and/or part will be repaired and/or replaced. If the unit is repaired, new or
reconditioned replacement parts may be used. If Alltrade chooses to replace 
the product, it may replace it with a new or reconditioned one of the same or 
comparable design. The repaired or replaced unit will be warranted under the terms
of the remainder of the warranty period. Typically, a defective product that is
returned within the first 30 days after the purchase date will be replaced; for items
returned after the first 30 days and within the warranty period, covered defective
parts not subject to normal wear and tear or other exclusions will be repaired or
replaced, at Alltrade’s option. During the warranty period, Alltrade will be responsi-
ble for the return shipping charges. Alltrade’s repair and/or replacement of any non-
conforming item and/or part thereof shall constitute fulfillment of all 
obligations to the purchaser. Alltrade shall not be responsible or liable for any
expense, including freight charges, or repairs made outside Alltrade’s facility, unless
expressly agreed to by Alltrade in writing. Under no circumstances shall Alltrade
bear any responsibility for loss of the unit, loss of time or rental, inconvenience,
commercial loss or consequential damages.
Exclusions
This warranty does not cover parts damaged due to normal wear, abnormal 
conditions, misapplication, misuse, abuse, accidents, operation at other than 
recommended pressures or temperatures, improper storage or freight damage.
Parts damaged or worn by operation in dusty environments are not warranted.
Failure to follow recommended operating and maintenance procedures also 
voids warranty.
This limited warranty does not apply to accessory items such as drill bits, 
screwdriving bits, circular saw blades, jigsaw blades, grinding wheels, sanding
sheets and other related items.
DAMAGE TO THE PRODUCT RESULTING FROM TAMPERING, ACCIDENT, ABUSE,
NEGLIGENCE, FAILURE TO FOLLOW INSTRUCTIONS, UNAUTHORIZED REPAIRS
OR ALTERATIONS, DAMAGE WHILE IN TRANSIT TO OUR SERVICE FACILITY, 
USE OF UNAPPROVED OR IMPROPER ATTACHMENTS OR ACCESSORIES, 
COMMERCIAL AND RENTAL APPLICATIONS OR OTHER CAUSES UNRELATED TO
PROBLEMS WITH MATERIAL OR WORKMANSHIP ARE NOT COVERED BY THIS
WARRANTY.
Alltrade will not be liable for the following: labor charges, loss or damage resulting
from improper operation, maintenance or repairs made by other persons; 
pre-delivery services such as assembly, oil or lubricants, and adjustment; 
maintenance services that are normally required to maintain the product.
The use of other than genuine Alltrade Repair Parts will void warranty.
22
2 YEAR LIMITED HOME USE WARRANTY
Express and Exclusive Limited Home Use Warranty to Original Retail Buyer
Alltrade Tools LLC (hereinafter Alltrade) expressly warrants to the original retail
purchaser of the accompanying KAWASAKI™ portable power tool and no one else
all parts of the product (except those parts referred to below which are specifically
excluded from such warranty (see Exclusions)) to be free from defects in materials
and workmanship for a period of two years from original date of purchase.
SPECIAL WARRANTY NOTE TO CONTRACTORS AND COMMERCIAL USERS:This
Kawasaki™ portable power tool is offered as a home use tool and carries a HOME
USE WARRANTY. This tool is made for home use in the execution of 
projects and repairs in and around the home. Use of the tool for COMMERCIAL 
PURPOSES OR ON A JOBSITEis not covered under this warranty.
The date of purchase shall be the date of shipment to the original purchaser, or the
date the original purchaser took possession, custody or control of the product,
whichever occurred first. This warranty shall be null and void if the product or any
component thereof is modified, altered or used for any commercial purpose or on
a jobsite. This warranty does not apply to any other product and/or component
thereof manufactured or distributed by Alltrade, and does not apply to products
and/or components thereof designed, manufactured and/or assembled by others,
for which Alltrade makes no warranties whatsoever.THERE ARE NO WARRANTIES
WHICH EXTEND BEYOND THE DESCRIPTION ON THE FACE HEREOF.
Warranty Performance 
By purchasing the product, purchaser expressly acknowledges and agrees that their
sole and exclusive remedy under this warranty shall be strictly limited to the repair
or replacement of any covered nonconforming items or parts thereof provided that
any such nonconforming item and/or part is promptly returned to Alltrade’s facility
postage pre-paid and insured (address: ALLTRADE Warranty Claims & Repair, 
1431 Via Plata, Long Beach, CA 90810, Attn: Customer Service #1-800-590-3723)
within the applicable warranty period, with a written request by purchaser that
Alltrade repair and/or replace the nonconforming item and/or part. We recommend
that you keep the original product packaging in the event you need to ship the unit.
We suggest the package be insured against loss or in transit damage. When 
sending your product include your name, address, phone number, dated proof 
of purchase (or copy), and a statement about the nature of problem. Warranty 
coverage is conditioned upon purchaser furnishing Alltrade with adequate written
proof that they are the original purchaser and of the original purchase date. Parts
returned, freight prepaid and insured, to Alltrade’s facility (see above address) will
be inspected and, at Alltrade’s option, repaired and/or replaced free of charge if
found to be defective and subject to warranty. Alltrade retains the sole discretion 
to determine whether any item or part is nonconforming and, if so, whether the 
21 
						

							REPRESENTATIVE(S) HAS BEEN ADVISED OF THE POSSIBILITY OF ANY SUCH
DAMAGES. IN NO EVENT, WHETHER AS A RESULT OF A BREACH OF CONTRACT,
WARRANTY, TORT (INCLUDING NEGLIGENCE) OR OTHERWISE, SHALL 
ALLTRADE’S AND/OR ITS REPRESENTATIVE(S)’ LIABILITY EXCEED THE PRICE OF
THE PRODUCT. ANY AND ALL LIABILITY CONNECTED WITH THE USE OF 
THIS PRODUCT SHALL TERMINATE UPON THE EXPIRATION OF THE WARRANTY
PERIODS SPECIFIED ABOVE.
Limitations on Warranty Disclaimers 
Some states do not allow limitations on how long an implied warranty lasts 
and some states do not allow the exclusion or limitation of the incidental or 
consequential damages, so part or all of the above limitations or exclusions may not
apply to you. This warranty gives you specific legal rights, and you may also have
other rights which vary from state to state.
If your product is not covered by this warranty, please call our Customer Service
Department toll free at 1-800-590-3723 for general repair information and charges.
24
Warranty Disclaimers 
EXCLUSION AND DISCLAIMER OF ALL OTHER EXPRESS WARRANTIES, 
GUARANTIES AND/OR REPRESENTATIONS. EXCEPT FOR THE LIMITED WARRANTY
PROVIDED ABOVE, ALL OTHER EXPRESS WARRANTIES, GUARANTIES AND/OR
REPRESENTATIONS BY ALLTRADE AND/OR ITS REPRESENTATIVE(S) REGARDING
THE DESIGN, MANUFACTURE, PURCHASE, USE AND/OR OPERATION OF THE
PRODUCT OR ANY COMPONENT THEREOF SOLD HEREUNDER, REGARDLESS OF
WHETHER ANY SUCH WARRANTY, GUARANTY AND/OR REPRESENTATION,
WRITTEN OR ORAL, ARISES BY OPERATION OF LAW AND/OR EQUITY AND/OR BY
ANY ACT OR OMISSION OF ALLTRADE AND/OR ITS REPRESENTATIVE(S), OR THE
BUYER, ARE HEREBY EXPRESSLY EXCLUDED AND DISCLAIMED BY ALLTRADE
AND/OR ITS REPRESENTATIVES. PURCHASER KNOWINGLY AND WILLINGLY
WAIVES ANY AND ALL SUCH WARRANTIES AND RIGHTS, CLAIMS AND/OR 
CAUSES OF ACTION ARISING THEREFROM OR BASED THEREON. PURCHASER’S
SOLE AND EXCLUSIVE REMEDY IS AS STATED ABOVE.
EXCLUSION AND DISCLAIMER OF ALL IMPLIED WARRANTIES, INCLUDING THE
IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR
PURPOSE. NO WARRANTY, ORAL OR WRITTEN, OTHER THAN THE ABOVE 
WARRANTY IS MADE WITH REGARD TO THIS PRODUCT. ALL EXPRESS AND/OR
IMPLIED WARRANTIES, GUARANTIES AND/OR REPRESENTATIONS BY ALLTRADE
AND/OR ITS REPRESENTATIVE(S) REGARDING THE DESIGN, MANUFACTURE,
PURCHASE, USE AND/OR OPERATION OF THE PRODUCT OR ANY COMPONENT
THEREOF SOLD HEREUNDER, REGARDLESS OF WHETHER ANY SUCH WARRANTY,
GUARANTY AND/OR REPRESENTATION, WRITTEN OR ORAL, ARISES BY 
OPERATION OF LAW AND/OR EQUITY AND/OR BY ANY ACT OR OMISSION OF
ALLTRADE AND/OR ITS REPRESENTATIVE(S), OR THE PURCHASER, INCLUDING
BUT NOT LIMITED TO THE IMPLIED WARRANTY OF MERCHANTABILITY AND THE
WARRANTY OF FITNESS FOR A PARTICULAR PURPOSE, ARE HEREBY EXPRESSLY
EXCLUDED AND DISCLAIMED BY ALLTRADE AND/OR ITS REPRESENTATIVES.
PURCHASER KNOWINGLY AND WILLINGLY WAIVES ANY AND ALL SUCH 
WARRANTIES AND RIGHTS, CLAIMS AND/OR CAUSES OF ACTION ARISING
THEREFROM OR BASED THEREON. PURCHASER’S SOLE AND EXCLUSIVE 
REMEDY IS AS STATED ABOVE.
Limitation Of Liability
IN NO EVENT SHALL ALLTRADE AND/OR ITS REPRESENTATIVE(S) BE LIABLE FOR
INDIRECT, INCIDENTAL, SPECIAL AND/OR CONSEQUENTIAL DAMAGES OF ANY
KIND ARISING OUT OF OR RELATED TO, DIRECTLY OR INDIRECTLY, ANY BREACH
OF ANY PROVISION OF ANY AGREEMENT BETWEEN ALLTRADE AND/OR ITS 
REPRESENTATIVE(S) AND PURCHASER, ANY WARRANTY HEREUNDER, 
AND/OR THE EXISTENCE, DESIGN, MANUFACTURE, PURCHASE, USE AND/OR
OPERATION OF ANY ITEM(S) SOLD HEREUNDER EVEN IF ALLTRADE AND/OR ITS
23 
						

							87-1904-60957
FOR CUSTOMER SERVICE
POUR LE SERVICE APRÉS VENTE
OU DU CONSOMMATEUR
PARA EL SERVICIO
PARA EL CONSUMIDOR1-800-590-3723
Printed in China
KAWASAKI™ IS A TRADEMARK LICENSED BY KAWASAKI™ MOTORS CORP.,
U.S.A., WHICH DOES NOT MANUFACTURE OR DISTRIBUTE THIS PRODUCT.
CONSUMER INQUIRES SHOULD BE DIRECTED TO:
©COPYRIGHT 2006 ALLTRADE TOOLS, LLC.
1431 VIA PLATA
LONG BEACH, CA 90810-1462 USA840056_19.2V Black Cordless Worklight_Rev 2/7/08
THIS MANUAL CONTAINS IMPORTANT INFORMATION REGARDING SAFETY, OPERATION,
MAINTENANCE AND STORAGE OF THIS PRODUCT. BEFORE USE, READ CAREFULLY AND
UNDERSTAND ALL CAUTIONS, WARNINGS, INSTRUCTIONS AND PRODUCT LABELS. FAILURE
TO DO SO COULD RESULT IN SERIOUS PERSONAL INJURY AND/OR PROPERTY DAMAGE.
IF YOU SHOULD HAVE ANY QUESTIONS OR EXPERIENCE A PROBLEM WITH YOUR ALLTRADE
PRODUCT, DO NOT RETURN THIS PRODUCT TO THE STORE. PLEASE CALL OUR CUSTOMER
SERVICE DEPARTMENT AT 1-800-590-3723. BEFORE YOU CALL, HAVE THE FOLLOWING
INFORMATION AVAILABLE: MODEL NO., DATE PURCHASED AND STORE LOCATION. AN 
ALLTRADE REPRESENTATIVE CAN RESOLVE YOUR PROBLEM OVER THE PHONE. IF YOU
WOULD LIKE TO MAKE A SUGGESTION OR COMMENT, GIVE US A CALL OR EMAIL US AT:
[email protected]. YOUR FEEDBACK IS VITAL TO US.
19.2V BATTERY-OPERATED WORKLIGHT
INSTRUCTION MANUAL
COMPONENT
#840056 
						

							C CO
ON
NG
GR
RA
AT
TU
UL
LA
AT
TI
IO
ON
NS
S!
!
Thanks for choosing this product. At Alltrade, our aim is to provide you with quality
products at an affordable price, and we want you to be totally satisfied with your
product and our Customer Service. If any help and advice is needed, please 
contact us at 1-800-590-3723. Properly cared for, this tool will give you many 
years of satisfaction.
I IN
NT
TE
EN
ND
DE
ED
D 
 U
US
SE
E
This tool is intended for consumer use only. Your charger and/or adapter has been
designed for charging batteries of the type approved and supplied with this tool.
R RE
EC
CO
OG
GN
NI
IZ
ZE
E 
 S
SA
AF
FE
ET
TY
Y 
 S
SY
YM
MB
BO
OL
LS
S,
, 
 W
WO
OR
RD
DS
S 
 A
AN
ND
D 
 L
LA
AB
BE
EL
LS
S
R RE
EA
AD
D 
 A
AN
ND
D 
 U
UN
ND
DE
ER
RS
ST
TA
AN
ND
D 
 A
AL
LL
L 
 I
IN
NS
ST
TR
RU
UC
CT
TI
IO
ON
NS
S.
.
Failure to
follow all instructions listed below may result in electric shock, fire and/or 
serious personal injury.S SA
AV
VE
E 
 T
TH
HE
ES
SE
E 
 I
IN
NS
ST
TR
RU
UC
CT
TI
IO
ON
NS
S 
 F
FO
OR
R 
 
F FU
UT
TU
UR
RE
E 
 R
RE
EF
FE
ER
RE
EN
NC
CE
E.
.
The safety instructions provided in this manual are not intended to cover all possible
conditions and practices that may occur when operating, maintaining and cleaning
power tools.
Always use common sense and pay particular attention to all the D DA
AN
NG
GE
ER
R
, 
W WA
AR
RN
NI
IN
NG
G
, C CA
AU
UT
TI
IO
ON
N
and N NO
OT
TE
E
statements of this manual.
This is the safety alert symbol. It is used to alert
you to potential personal injury hazards. Obey all
safety messages that follow this symbol to avoid
possible injury or death.
D DA
AN
NG
GE
ER
R
indicates an imminently hazardous 
situation which, if not avoided, will result in death
or serious injury.
W WA
AR
RN
NI
IN
NG
G
indicates a potentially hazardous 
situation which, if not avoided, could result in
death or serious injury.
T TA
AB
BL
LE
E 
 O
OF
F 
 C
CO
ON
NT
TE
EN
NT
TS
S
C CO
ON
NG
GR
RA
AT
TU
UL
LA
AT
TI
IO
ON
NS
S!
!
 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2
I IN
NT
TE
EN
ND
DE
ED
D 
 U
US
SE
E
 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2
S SE
EC
CT
TI
IO
ON
N 
 O
ON
NE
E
RECOGNIZE SAFETY SYMBOLS, WORDS AND LABELS . . . . . . . . . . . . 2-3
IMPORTANT SAFEGUARDS  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3
BATTERY TOOL USE AND CARE  . . . . . . . . . . . . . . . . . . . . . . . . . . 4
SERVICE  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
S SE
EC
CT
TI
IO
ON
N 
 T
TW
WO
O
SAFETY RULES FOR WORKLIGHT  . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
SYMBOLS  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
S SE
EC
CT
TI
IO
ON
N 
 T
TH
HR
RE
EE
E
FUNCTIONAL DESCRIPTION  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
BATTERY  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7-9
REMOVING/ATTACHING BATTERY PACK  . . . . . . . . . . . . . . . . . . . . 7
CHARGER  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
CHARGING BATTERY PACK  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
OPERATING THE WORKLIGHT  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9-11
OPERATING THE ON/OFF SWITCH  . . . . . . . . . . . . . . . . . . . . . . . . . 10
ADJUSTING THE WORKLIGHT BEAM  . . . . . . . . . . . . . . . . . . . . . . 10
REPLACING THE LIGHT BULB  . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10-11
S SE
EC
CT
TI
IO
ON
N 
 F
FO
OU
UR
R
MAINTENANCE AND CLEANING  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
ACCESSORIES  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
SPECIFICATIONS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
PROTECTING THE ENVIRONMENT  . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
OTHER CONSUMER DO-IT-YOURSELF (DIY) TOOLS  . . . . . . . . . . . . . . 13
S SE
EC
CT
TI
IO
ON
N 
 F
FI
IV
VE
E
2 YEAR LIMITED WARRANTY . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13-16
12 
						

							B BA
AT
TT
TE
ER
RY
Y 
 T
TO
OO
OL
L 
 U
US
SE
E 
 A
AN
ND
D 
 C
CA
AR
RE
E
E En
ns
su
ur
re
e 
 t
th
he
e 
 s
sw
wi
it
tc
ch
h 
 i
is
s 
 i
in
n 
 t
th
he
e 
 o
of
ff
f 
 p
po
os
si
it
ti
io
on
n 
 b
be
ef
fo
or
re
e 
 i
in
ns
se
er
rt
ti
in
ng
g 
 b
ba
at
tt
te
er
ry
y 
 p
pa
ac
ck
k.
.
Inserting the battery pack into power tools that have the switch on invites acci-
dents.
R
Re
ec
ch
ha
ar
rg
ge
e 
 o
on
nl
ly
y 
 w
wi
it
th
h 
 t
th
he
e 
 c
ch
ha
ar
rg
ge
er
r 
 s
sp
pe
ec
ci
if
fi
ie
ed
d 
 b
by
y 
 t
th
he
e 
 m
ma
an
nu
uf
fa
ac
ct
tu
ur
re
er
r.
.
A charger that
is suitable for one type of battery pack may create a risk of fire when used with 
another battery pack.
U Us
se
e 
 p
po
ow
we
er
r 
 t
to
oo
ol
ls
s 
 o
on
nl
ly
y 
 w
wi
it
th
h 
 s
sp
pe
ec
ci
if
fi
ic
ca
al
ll
ly
y 
 d
de
es
si
ig
gn
na
at
te
ed
d 
 b
ba
at
tt
te
er
ry
y 
 p
pa
ac
ck
ks
s.
.
Use of any
other battery packs may create a risk of injury and fire.
W Wh
he
en
n 
 b
ba
at
tt
te
er
ry
y 
 p
pa
ac
ck
k 
 i
is
s 
 n
no
ot
t 
 i
in
n 
 u
us
se
e,
, 
 k
ke
ee
ep
p 
 i
it
t 
 a
aw
wa
ay
y 
 f
fr
ro
om
m 
 o
ot
th
he
er
r 
 m
me
et
ta
al
l 
 o
ob
bj
je
ec
ct
ts
s 
 l
li
ik
ke
e
p pa
ap
pe
er
r 
 c
cl
li
ip
ps
s,
, 
 c
co
oi
in
ns
s,
, 
 k
ke
ey
ys
s,
, 
 n
na
ai
il
ls
s,
, 
 s
sc
cr
re
ew
ws
s,
, 
 o
or
r 
 o
ot
th
he
er
r 
 s
sm
ma
al
ll
l 
 m
me
et
ta
al
l 
 o
ob
bj
je
ec
ct
ts
s 
 t
th
ha
at
t 
 c
ca
an
n
m ma
ak
ke
e 
 a
a 
 c
co
on
nn
ne
ec
ct
ti
io
on
n 
 f
fr
ro
om
m 
 o
on
ne
e 
 t
te
er
rm
mi
in
na
al
l 
 t
to
o 
 a
an
no
ot
th
he
er
r.
.
Shorting the battery termi-
nals together may cause burns or a fire.
U Un
nd
de
er
r 
 a
ab
bu
us
si
iv
ve
e 
 c
co
on
nd
di
it
ti
io
on
ns
s,
, 
 l
li
iq
qu
ui
id
d 
 m
ma
ay
y 
 b
be
e 
 e
ej
je
ec
ct
te
ed
d 
 f
fr
ro
om
m 
 t
th
he
e 
 b
ba
at
tt
te
er
ry
y,
, 
 a
av
vo
oi
id
d 
 c
co
on
n-
-
t ta
ac
ct
t.
.
If contact accidentally occurs, flush with water. If liquid contacts eyes,
additionally seek medical help. Liquid ejected from the battery may cause irrita-
tion or burns.
S SE
ER
RV
VI
IC
CE
E
Have your power tool serviced by a qualified repair person
using only identical replacement parts. This will ensure that the safety of the
power tool is maintained.
S SA
AF
FE
ET
TY
Y 
 R
RU
UL
LE
ES
S 
 F
FO
OR
R 
 W
WO
OR
RK
KL
LI
IG
GH
HT
T
U Us
se
e 
 b
ba
at
tt
te
er
ry
y 
 o
op
pe
er
ra
at
te
ed
d 
 t
to
oo
ol
l 
 o
on
nl
ly
y 
 w
wi
it
th
h 
 s
sp
pe
ec
ci
if
fi
ic
ca
al
ll
ly
y 
 d
de
es
si
ig
gn
na
at
te
ed
db
ba
at
tt
te
er
ry
y 
 p
pa
ac
ck
k.
.
Use of
any other batteries may create risk of fire.
Keep the handle of the Worklight dry, clean, and free from oil and grease.
D Do
o 
 n
no
ot
t 
 r
ru
un
n 
 t
th
he
e 
 W
Wo
or
rk
kl
li
ig
gh
ht
t 
 w
wh
hi
il
le
e 
 c
ca
ar
rr
ry
yi
in
ng
g 
 i
it
t 
 a
at
t 
 y
yo
ou
ur
r 
 s
si
id
de
e.
.
The worklight heats up
immediately when in use and could result in burns.
Do not use the Worklight if it has been damaged, left outdoors in the rain, snow,
wet or damp environments, or immersed in liquid.
M Ma
ai
in
nt
ta
ai
in
n 
 l
la
ab
be
el
ls
s 
 a
an
nd
d 
 n
na
am
me
ep
pl
la
at
te
es
s 
 o
on
n 
 t
th
he
e 
 W
Wo
or
rk
kl
li
ig
gh
ht
t.
. 
 
These carry important
4
C CA
AU
UT
TI
IO
ON
N
indicates a potentially hazardous 
situation which, if not avoided, may result in
minor or moderate injury.
C CA
AU
UT
TI
IO
ON
N
used without the safety alert symbol
indicates a potentially hazardous situation which,
if not avoided, may result in property damage.
N NO
OT
TE
E
provides additional information that is useful
for proper use and maintenance of this tool. If a
NOTE is indicated make sure it is fully understood.
I IM
MP
PO
OR
RT
TA
AN
NT
T 
 S
SA
AF
FE
EG
GU
UA
AR
RD
DS
S
P
Pe
eo
op
pl
le
e 
 w
wi
it
th
h 
 e
el
le
ec
ct
tr
ro
on
ni
ic
c 
 d
de
ev
vi
ic
ce
es
s,
, 
 s
su
uc
ch
h 
 a
as
s 
 p
pa
ac
ce
em
ma
ak
ke
er
rs
s,
, 
 s
sh
ho
ou
ul
ld
d 
 c
co
on
ns
su
ul
lt
t 
 t
th
he
ei
ir
r
p ph
hy
ys
si
ic
ci
ia
an
n(
(s
s)
) 
 b
be
ef
fo
or
re
e 
 u
us
si
in
ng
g 
 t
th
hi
is
s 
 p
pr
ro
od
du
uc
ct
t.
. 
 O
Op
pe
er
ra
at
ti
io
on
n 
 o
of
f 
 e
el
le
ec
ct
tr
ri
ic
ca
al
l 
 e
eq
qu
ui
ip
pm
me
en
nt
t 
 i
in
n
c cl
lo
os
se
e 
 p
pr
ro
ox
xi
im
mi
it
ty
y 
 t
to
o 
 a
a 
 h
he
ea
ar
rt
t 
 p
pa
ac
ce
em
ma
ak
ke
er
r 
 c
co
ou
ul
ld
d 
 c
ca
au
us
se
e 
 i
in
nt
te
er
rf
fe
er
re
en
nc
ce
e 
 o
or
r 
 f
fa
ai
il
lu
ur
re
e 
 o
of
f
t th
he
e 
 p
pa
ac
ce
em
ma
ak
ke
er
r.
.
W WA
AR
RN
NI
IN
NG
G:
:
Some dust created by power sanding, sawing, grinding, drilling and
other construction activities contains chemicals known to the State of California
to cause cancer, birth defects or other reproductive harm.
Some examples of these chemicals are:
• Lead from lead-based paints. 
• Crystalline silica from bricks and cement and other masonry products,
and arsenic and chromium from chemically-treated lumber.
Your risk from these exposures varies, depending on how often you do this type
of work. To reduce your exposure to these chemicals: work in a well ventilated
area, and work with approved safety equipment, such as dust masks that are
specially designed to filter out microscopic particles.
W WA
AR
RN
NI
IN
NG
G:
: 
 
Handling the power cord on corded products may expose you to
lead, a chemical known to the State of California to cause cancer and birth
defects or other reproductive harm.
W Wa
as
sh
h 
 h
ha
an
nd
ds
s 
 a
af
ft
te
er
r 
 h
ha
an
nd
dl
li
in
ng
g.
.3 
						

							F FU
UN
NC
CT
TI
IO
ON
NA
AL
L 
 D
DE
ES
SC
CR
RI
IP
PT
TI
IO
ON
N
C CO
ON
NT
TR
RO
OL
LS
S 
 A
AN
ND
D 
 C
CO
OM
MP
PO
ON
NE
EN
NT
TS
S:
:
1. Battery Pack
2. Release Buttons on Each Side
3. 120V AC Adapter
4. Charger
5. LED Charging Indicators
C CO
OM
MP
PO
ON
NE
EN
NT
TM
MO
OD
DE
EL
L 
 N
NU
UM
MB
BE
ER
RBATTERY PACK 690506120V AC ADAPTER 690074CHARGER 690071
6
information. If unreadable or missing, contact Alltrade for a replacement.
B Ba
at
tt
te
er
ry
y 
 p
pa
ac
ck
k 
 m
mu
us
st
t 
 b
be
e 
 r
re
ec
ch
ha
ar
rg
ge
ed
d 
 o
on
nl
ly
y 
 w
wi
it
th
h 
 t
th
he
e 
 s
sp
pe
ec
ci
if
fi
ie
ed
d 
 c
ch
ha
ar
rg
ge
er
r 
 f
fo
or
r 
 t
th
he
e 
 b
ba
at
t-
-
t te
er
ry
y.
.
A charger that may be suitable for one type of battery may create a risk of fire
when used with another battery.
Do not use in a damp or wet environment.
S St
to
or
re
e 
 o
ou
ut
t 
 o
of
f 
 r
re
ea
ac
ch
h 
 o
of
f 
 c
ch
hi
il
ld
dr
re
en
n 
 a
an
nd
d 
 o
ot
th
he
er
r 
 u
un
nt
tr
ra
ai
in
ne
ed
d 
 p
pe
er
rs
so
on
ns
s.
.
S
SY
YM
MB
BO
OL
LS
S
I IM
MP
PO
OR
RT
TA
AN
NT
T:
: 
 
Some of the following symbols may be used on your tool. Please
study them and learn their meaning. Proper interpretation of these symbols will
allow you to operate the tool better and safer.
S SY
YM
MB
BO
OL
LN
NA
AM
ME
EE
EX
XP
PL
LA
AN
NA
AT
TI
IO
ON
N
V Volts Voltage (Potential)A Amperes CurrentHz Hertz Frequency (Cycles per Second)W Watt PowerKg Kilograms Weight
Alternating Current Type of CurrentDirect Current Type of CurrentAlternating or Direct Current Type of CurrentEarthing Terminal Grounding TerminalClass II Construction Denotes Double Insulation
min Minutes Times Seconds Time

Diameter Size of Drill Bits, 
Grinding Wheels, etc.
No load speed No-load Rotational Speed
.../min Revolutions per Minute Revolutions, Surface Speed, 
Strokes, etc. per Minute
1,2,3, … Ring Selector Settings Speed, Torque or Position Settings
5
6. ON/OFF Switch
7. Reflector Rim
A AC
CC
CE
ES
SS
SO
OR
RI
IE
ES
S:
:
8. Replacement Light bulb (inside unit)
8
6
2
1
5
4
3
7