AllTrade Kawasaki 192V Cordless Circular Saw 840056 User Manual

							FUNCTIONAL DESCRIPTION
CONTROLS AND COMPONENTS:
1. Battery Pack
2. Release Buttons on Each Side
3. 120V AC Adapter
4. Charger
5. LED Charging Indicators
6. 10mm (3/8) Keyless Chuck
7. 24+1 Adjustable Torque Settings
Control Ring
8. Forward/Reversing and 
Trigger Lock Lever
COMPONENT MODEL NUMBERBATTERY PACK 690071120V AC ADAPTER 690074CHARGER 69007210mm (3/8) KEYLESS CHUCK690076
9
BATTERY
Before using battery pack, please read carefully all instruc-
tions and cautionarymarkings on battery pack, battery
charger and product using battery.
Do not incinerate the battery pack even if it is severely dam-
aged or is completely worn out.The battery pack can explode.
Do not carry battery packs in aprons, pockets, or tool
boxes, product kit boxes, drawers, etc. with loose metal objects.Battery
pack terminals could be short circuited causing damage to the battery pack,
severe burns or fire.
The battery pack is Nickel-Cadmium (Ni-Cad) and is considered to be a toxic
material by the Environmental Protection Agency.Before disposing of dam-
aged or worn out Ni-Cad battery packs, check with your State Environmental
Protection Agency to find out about special restrictions on the disposal of these
battery packs, take them to your local recycling center for proper disposal, or
call 1-800-822-8837.
The battery is not fully charged. Before first use, the battery pack requires 
8-10 hours charge time to be fully charged. Subsequent recharging needs 3-5
hours for the battery to be fully charged. 
Always switch to a fresh battery when tool performance begins to diminish.
Severe heat is most destructive to a battery; the more heat generated, the faster
the battery loses power. A battery that gets too hot can have a shortened life. 
Never over-discharge a battery by using the tool even after tool performance
has decreased.Do not attempt to discharge a tool’s battery by continuing to
pull on the tool trigger. When tool performance begins to diminish, stop the tool
and recharge the battery for optimal performance.
Charge battery pack at ambient temperatures between 50° F – 104° F. 
Store tool and battery pack in locations where temperatures will not exceed
120°F. This is important to prevent serious damage to the battery cells.
The battery pack should always be recharged when the Cordless Drill begins to
run slowly. 
When battery pack is not in use, keep it away from other metal objects such as
paper clips, coins, keys, nails, screws or other small metal objects that can
make a connection from one terminal to another.Shorting the battery terminals
together may cause sparks, burns, or fire.  
10
®
1211
6
7
10
9
8
2
1
13
3
4
5
9. High/Low Speed Switch
10. Variable Speed Controlled 
Trigger Switch
11. Accessory/Bit Holder
12. Comfort Rubber Grip
ACCESSORIES:
13. Double Ended Screwdriver Bits (2) 
						

							REMOVING / ATTACHING BATTERY PACK
REMOVE BATTERY PACK:
1. Press both release buttons on either side of 
the Cordless Drill to release the battery
pack.
2. Pull battery pack free of Cordless Drill.
ATTACH BATTERY PACK:
1. Align the raised portion of the battery pack 
with the groove in the battery compartment 
of the Cordless Drill.
2. Press the battery pack into place. Make
sure the latches are securely fastened. Do
not use the Cordless Drill if the battery
pack is not seated properly. 
CHARGER
Before using battery charger, please read carefully all
instructions and cautionary markings on battery charger, battery pack and
product using battery.
The charger will not automatically turn “OFF” when the
battery pack is fully charged.The charging indicator light will remain “ON”
until the charger is disconnected from the electrical outlet. 
Use only the charger which accompanied your product or direct replacement as
listed in this manual. Do not substitute any other charger. Use only Alltrade
approved chargers with your product.
Do not disassemble charger.
Do not use charger if it has been damaged, left outdoors in the rain, snow, wet
or damp environments, or immersed in liquid.
The battery pack and charger heat during charging. Place the charger on a flat, 
non-flammable surface away from flammable materials with at least four inches of
clearance to allow proper air circulation around the charger and battery pack.
When the battery pack requires recharging, a 3-5 hour charge allows the tool to
operate at full power.A charging indicator light on the charger will illuminate to
show that charging is taking place. 
CHARGING BATTERY PACK
CHARGE BATTERY PACK:
1. Make sure the trigger 
on the Cordless Drill 
is in the “OFF”position 
and remove the battery 
pack from the Cordless
Drill.
2. Plug 120V AC Adapter 
into household outlet 
and into side of battery 
charger. Insert battery 
pack into battery charger. 
When the battery is
placed in the charger, the
red LED indicator light will remain on.
3. When fully charged, reattach battery pack onto Cordless Drill, 
making certain latches fasten securely. Cordless Drill will not 
operate properly if the battery pack is not seated properly.
ASSEMBLY
Be aware that this tool is always in an operating condition
because it does not have to be plugged into an electrical outlet.Always turn
the switch “OFF”and remove the battery pack before changing bits.
INSTALLING DRILL BIT INTO KEYLESS CHUCK
Before inserting a drill bit or other accessory,make sure the forward/reverse
and trigger lock lever is in the center “OFF”position to prevent accidental starts
that may result in injury.
Do not attempt to tighten drill bits (or any other accessory) by gripping the
front of the chuck and turning the tool on.This may cause personal injury
and/or damage to the chuck.
When removing the bit from the tool, avoid contact with skin and use proper
protective gloves when grasping the bit or accessory.Accessories may be hot
after prolonged use.
WARNING
12 11
BATTERY PACK
120V AC 
ADAPTER
LED LIGHT
BATTERY
CHARGER
RELEASE 
BUTTON 
						

							FORWARD/REVERSE AND TRIGGER LOCK LEVER
Be sure the trigger is released when changing the position of the lever.
Always store the tool in the“LOCKED/OFF”position.
Always check the direction of the Cordless Drills rotation before use.
TO SELECT THE DIRECTIONS 
OF ROTATION:
• To select forward Cordless Drill 
rotation, press the trigger lock 
from left to right flat against the Cordless
Drill body.
• To select reverse, press the trigger lock lever
in the opposite direction.
• The center position locks the tool.
TORQUE SETTINGS
To prevent damaging the tool or driving screw too deep
into work piece, release the trigger when you feel the clutch slip.
THE CONTROL RING ADJUSTS THE LEVEL OF TORQUE:
• For light duty work, use lower settings.
• For heavy duty work, use higher settings.
PROPER SETTING FOR DRIVING SCREWS:
1. Set the ring on the lowest 
setting to begin.
2. Try tightening the first screw. 
If the drill drives smoothly, 
proceed with the next screw.
3. If the Drill’s clutch slips, 
increase the torque setting 
and try again until the Drill 
drives the screw without incident.
14
1. Hold the rear end of the chuck
in one hand and use the other
hand to rotate the front end in a
counterclockwise direction to
open the jaws of the chuck.
2. Insert the shank of the bit (or
other accessory) fully into the
keyless chuck, taking care to
keep the bit in the center of 
the jaws of the chuck.
3. Turn the front end of the chuck clockwise to hold the bit in place.
4. Tighten securely by turning the front end of the chuck clockwise while holding
the rear end.
OPERATING THE DRILL
Never tape the trigger switch down to provide continu-
ous high speed.The tool may fail under such conditions causing fire or 
personal injury.
VARIABLE SPEED TRIGGER SWITCH
THIS TOOL IS CONTROLLED 
BY A TRIGGER SWITCH:
• The speed of the Cordless Drill depends 
on the amount of pressure you put on the
trigger.
• The more pressure you apply, the faster
the Cordless Drill  will go.
• Release the pressure and the Cordless Drill
will slow down. 
13
CONTROL RING
TRIGGER
LOCK
TRIGGER
SWITCHTIGHTENLOOSEN
HOLD 
						

							DRILLING WOOD
Use twist bits to drill holes in wood. Make sure the bits are sharp. Pull the bits 
out of the hole frequently to clear chips from the flutes as an overburdened bit 
may overheat. 
HINTS FOR OPTIMUM USE
DRILLING:
• Keep the right amount of pressure in a straight line with the drill bit. Too little and
the bit will spin without cutting, too much and the motor may stall.
• Just before the drill tip breaks though the other side of the work piece drill more
slowly and decrease pressure on the tool. This will prevent stalling and leave a
cleaner hole.
• Use a block of wood to back up work pieces that may splinter.
• Use spade bits when drilling large diameter holes in wood.
• Use HSS drill bits when drilling in metal.
• Use masonry bits when drilling in soft masonry.
• Use a lubricant when drilling metals other than cast iron, aluminum, copper, 
and brass.
• When drilling, start the hole slowly, allowing the bit to drill deep enough to prevent
slipping at higher speeds.
• Never try to start a stalled Drill by clicking the trigger switch “ON”and “OFF”.
This may damage your tool.
• To reduce jamming, always keep the Drill running when pulling the bit out of a 
finished hole.
SCREWDRIVING:
• Always use the correct type and size of screwdriver bit.
• If screws are difficult to tighten, try applying a small amount of washing liquid or
soap as a lubricant.
• Always hold the tool and screwdriver bit in a straight line with the screw.MAINTENANCE AND CLEANING
Always remove the battery pack before attempting
cleaning or maintenance.
HIGH / LOW SPEED (GEAR) SHIFTING
FOR LOW SPEED SETTING:
• Slide the switch on top of the 
Drill to Position 1 for high
torque applications and driving
screws.
FOR HIGH SPEED SETTING:
• Slide the switch to Position 2 
for light duty projects.
SCREWDRIVING
WHEN DRIVING FASTENERS:
• Always start slowly and gradually increase the speed of the Drill. 
• Release the trigger when you feel the clutch slip.
• Always keep the driver bit straight to prevent damage to the screw. 
• Hold the Drill with both hands to ensure control if the bit should stick or slip.
• To prevent wood from splitting, drill pilot holes into the wood before driving 
in the screws.DRILLING METAL
WHEN DRILLING HARD METALS:
• Apply a lubricant, such as cutting oil, to the tip of the bit.
• Start with a small hole then enlarge to the required size. Make sure the bit is 
actually cutting and not spinning in the hole as this will dull the edges of the bit.
• Keep enough pressure on the bit to keep it drilling through the material.DRILLING MASONRY
WHEN DRILLING MASONRY:
• Masonry can be brittle so be careful not to apply too much pressure and crack 
the material.
• Apply enough pressure to keep the bit cutting and not spinning in the hole as this
will dull the edges of the bit.
• Bricks and similar soft materials will require less pressure, concrete will require
much more.
1516
HIGH SPEED LOW SPEED 
						

							SPECIFICATIONS
SPECIFICATIONSVoltage 19.2V Low Speed 0-400/min.High Speed 0-1100/min.Torque Settings 24+1 DrillChuck Capacity Up to 10mm Charger Input 120V  60HzCharging Time Approx. 3-5 hoursBattery Type Ni-Cad
PROTECTING THE ENVIRONMENT
BATTERIES
Alltrade batteries can be recharged many times. At the end of their useful life, 
recycle batteries with due care for our environment. 
Ni-Cad and Ni-MH batteries are recyclable. Take them to your local recycling center
or call 1-800-822-8837. Collected batteries will be recycled or disposed of properly.
OTHER CONSUMER DO-IT-YOURSELF (DIY) TOOLS
Alltrade offers a full range of Kawasaki™ tools that make DIY jobs easy. If you would
like further information on the following products, please contact Alltrade Customer
Service Department at 1-800-590-3723. 
Cordless Drills/Screwdrivers
Impact Wrenches
Sanders
Jigsaws
Circular Saws
Angle Grinders
Reciprocating Saws
Routers
Rotary Tools
Corded and Cordless Multi-Purpose Tools
Wide Range of Accessories and more
18 17
This Cordless Drill is lubricated before it leaves the 
factory. This lubrication should last for the life of the tool. No further 
lubrication is required.
Use only mild soap and a damp cloth to clean the tool.Never let any liquid get
inside the casing. Never immerse any part of the tool in a liquid. Always keep the
ventilation openings clear.
Always clean the battery pack using only a dry cloth. Do not use liquids. 
Always unplug the charger before cleaning it.
Regularly clean the ventilation slots in your tool and charger using only a soft
brush or dry cloth.
Never open the Cordless Drill case, battery pack or charger.Do not attempt to
repair the Cordless Drill, battery pack or charger yourself. Opening any of these
parts will void your warranty.
ACCESSORIES
Use only accessories that are recommended by the manufacturer for your model.
Accessories that may be suitable for one tool may become hazardous when used on
another tool.
Always attach grounded (3-prong) extension cords to grounded (3-hole) outlets.
If you must use an extension cord, be sure that the gauge is large enough to carry
the amount of current necessary for your power tool.If not, your tool may experi-
ence a loss of power, excessive voltage drop or overheating. The smaller the gauge
number, the heavier the cord (see table below).
RECOMMENDED SIZES OF EXTENSION CORDS 120 VOLT AC 60 HZ TOOLS
TOOL CURRENT RATING CONDUCTOR SIZE IN A.W.GAMPERE 10FT. 25FT. 50FT. 100FT.
3-6 18 18 18 186-8 18 18 18 168-10 18 18 18 1410-12 16 16 14 1412-16 14 12 12 -16-20 12 12 12 - 
						

							item and/or part will be repaired and/or replaced. If the unit is repaired, new or
reconditioned replacement parts may be used. If Alltrade chooses to replace 
the product, it may replace it with a new or reconditioned one of the same or 
comparable design. The repaired or replaced unit will be warranted under the terms
of the remainder of the warranty period. Typically, a defective product that is
returned within the first 30 days after the purchase date will be replaced; for items
returned after the first 30 days and within the warranty period, covered defective
parts not subject to normal wear and tear or other exclusions will be repaired or
replaced, at Alltrade’s option. During the warranty period, Alltrade will be responsi-
ble for the return shipping charges. Alltrade’s repair and/or replacement of any non-
conforming item and/or part thereof shall constitute fulfillment of all 
obligations to the purchaser. Alltrade shall not be responsible or liable for any
expense, including freight charges, or repairs made outside Alltrade’s facility, unless
expressly agreed to by Alltrade in writing. Under no circumstances shall Alltrade
bear any responsibility for loss of the unit, loss of time or rental, inconvenience,
commercial loss or consequential damages.
Exclusions
This warranty does not cover parts damaged due to normal wear, abnormal 
conditions, misapplication, misuse, abuse, accidents, operation at other than 
recommended pressures or temperatures, improper storage or freight damage.
Parts damaged or worn by operation in dusty environments are not warranted.
Failure to follow recommended operating and maintenance procedures also 
voids warranty.
This limited warranty does not apply to accessory items such as drill bits, 
screwdriving bits, circular saw blades, jigsaw blades, grinding wheels, sanding
sheets and other related items.
DAMAGE TO THE PRODUCT RESULTING FROM TAMPERING, ACCIDENT, ABUSE,
NEGLIGENCE, FAILURE TO FOLLOW INSTRUCTIONS, UNAUTHORIZED REPAIRS
OR ALTERATIONS, DAMAGE WHILE IN TRANSIT TO OUR SERVICE FACILITY, 
USE OF UNAPPROVED OR IMPROPER ATTACHMENTS OR ACCESSORIES, 
COMMERCIAL AND RENTAL APPLICATIONS OR OTHER CAUSES UNRELATED TO
PROBLEMS WITH MATERIAL OR WORKMANSHIP ARE NOT COVERED BY THIS
WARRANTY.
Alltrade will not be liable for the following: labor charges, loss or damage resulting
from improper operation, maintenance or repairs made by other persons; 
pre-delivery services such as assembly, oil or lubricants, and adjustment; 
maintenance services that are normally required to maintain the product.
The use of other than genuine Alltrade Repair Parts will void warranty.
20 19
2 YEAR LIMITED HOME USE WARRANTY
Express and Exclusive Limited Home Use Warranty to Original Retail Buyer
Alltrade Tools LLC (hereinafter Alltrade) expressly warrants to the original retail
purchaser of the accompanying KAWASAKI™ portable power tool and no one else
all parts of the product (except those parts referred to below which are specifically
excluded from such warranty (see Exclusions)) to be free from defects in materials
and workmanship for a period of two years from original date of purchase.
SPECIAL WARRANTY NOTE TO CONTRACTORS AND COMMERCIAL USERS:This
Kawasaki™ portable power tool is offered as a home use tool and carries a HOME
USE WARRANTY. This tool is made for home use in the execution of 
projects and repairs in and around the home. Use of the tool for COMMERCIAL 
PURPOSES OR ON A JOBSITEis not covered under this warranty.
The date of purchase shall be the date of shipment to the original purchaser, or the
date the original purchaser took possession, custody or control of the product,
whichever occurred first. This warranty shall be null and void if the product or any
component thereof is modified, altered or used for any commercial purpose or on
a jobsite. This warranty does not apply to any other product and/or component
thereof manufactured or distributed by Alltrade, and does not apply to products
and/or components thereof designed, manufactured and/or assembled by others,
for which Alltrade makes no warranties whatsoever.THERE ARE NO WARRANTIES
WHICH EXTEND BEYOND THE DESCRIPTION ON THE FACE HEREOF.
Warranty Performance 
By purchasing the product, purchaser expressly acknowledges and agrees that their
sole and exclusive remedy under this warranty shall be strictly limited to the repair
or replacement of any covered nonconforming items or parts thereof provided that
any such nonconforming item and/or part is promptly returned to Alltrade’s facility
postage pre-paid and insured (address: ALLTRADE Warranty Claims & Repair, 
1431 Via Plata, Long Beach, CA 90810, Attn: Customer Service #1-800-590-3723)
within the applicable warranty period, with a written request by purchaser that
Alltrade repair and/or replace the nonconforming item and/or part. We recommend
that you keep the original product packaging in the event you need to ship the unit.
We suggest the package be insured against loss or in transit damage. When 
sending your product include your name, address, phone number, dated proof 
of purchase (or copy), and a statement about the nature of problem. Warranty 
coverage is conditioned upon purchaser furnishing Alltrade with adequate written
proof that they are the original purchaser and of the original purchase date. Parts
returned, freight prepaid and insured, to Alltrade’s facility (see above address) will
be inspected and, at Alltrade’s option, repaired and/or replaced free of charge if
found to be defective and subject to warranty. Alltrade retains the sole discretion 
to determine whether any item or part is nonconforming and, if so, whether the  
						

							REPRESENTATIVE(S) HAS BEEN ADVISED OF THE POSSIBILITY OF ANY SUCH
DAMAGES. IN NO EVENT, WHETHER AS A RESULT OF A BREACH OF CONTRACT,
WARRANTY, TORT (INCLUDING NEGLIGENCE) OR OTHERWISE, SHALL 
ALLTRADE’S AND/OR ITS REPRESENTATIVE(S)’ LIABILITY EXCEED THE PRICE OF
THE PRODUCT. ANY AND ALL LIABILITY CONNECTED WITH THE USE OF 
THIS PRODUCT SHALL TERMINATE UPON THE EXPIRATION OF THE WARRANTY
PERIODS SPECIFIED ABOVE.
Limitations on Warranty Disclaimers 
Some states do not allow limitations on how long an implied warranty lasts 
and some states do not allow the exclusion or limitation of the incidental or 
consequential damages, so part or all of the above limitations or exclusions may not
apply to you. This warranty gives you specific legal rights, and you may also have
other rights which vary from state to state.
If your product is not covered by this warranty, please call our Customer Service
Department toll free at 1-800-590-3723 for general repair information and charges. 
22
Warranty Disclaimers 
EXCLUSION AND DISCLAIMER OF ALL OTHER EXPRESS WARRANTIES, 
GUARANTIES AND/OR REPRESENTATIONS. EXCEPT FOR THE LIMITED WARRANTY
PROVIDED ABOVE, ALL OTHER EXPRESS WARRANTIES, GUARANTIES AND/OR
REPRESENTATIONS BY ALLTRADE AND/OR ITS REPRESENTATIVE(S) REGARDING
THE DESIGN, MANUFACTURE, PURCHASE, USE AND/OR OPERATION OF THE
PRODUCT OR ANY COMPONENT THEREOF SOLD HEREUNDER, REGARDLESS OF
WHETHER ANY SUCH WARRANTY, GUARANTY AND/OR REPRESENTATION,
WRITTEN OR ORAL, ARISES BY OPERATION OF LAW AND/OR EQUITY AND/OR BY
ANY ACT OR OMISSION OF ALLTRADE AND/OR ITS REPRESENTATIVE(S), OR THE
BUYER, ARE HEREBY EXPRESSLY EXCLUDED AND DISCLAIMED BY ALLTRADE
AND/OR ITS REPRESENTATIVES. PURCHASER KNOWINGLY AND WILLINGLY
WAIVES ANY AND ALL SUCH WARRANTIES AND RIGHTS, CLAIMS AND/OR 
CAUSES OF ACTION ARISING THEREFROM OR BASED THEREON. PURCHASER’S
SOLE AND EXCLUSIVE REMEDY IS AS STATED ABOVE.
EXCLUSION AND DISCLAIMER OF ALL IMPLIED WARRANTIES, INCLUDING THE
IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR
PURPOSE. NO WARRANTY, ORAL OR WRITTEN, OTHER THAN THE ABOVE 
WARRANTY IS MADE WITH REGARD TO THIS PRODUCT. ALL EXPRESS AND/OR
IMPLIED WARRANTIES, GUARANTIES AND/OR REPRESENTATIONS BY ALLTRADE
AND/OR ITS REPRESENTATIVE(S) REGARDING THE DESIGN, MANUFACTURE,
PURCHASE, USE AND/OR OPERATION OF THE PRODUCT OR ANY COMPONENT
THEREOF SOLD HEREUNDER, REGARDLESS OF WHETHER ANY SUCH WARRANTY,
GUARANTY AND/OR REPRESENTATION, WRITTEN OR ORAL, ARISES BY 
OPERATION OF LAW AND/OR EQUITY AND/OR BY ANY ACT OR OMISSION OF
ALLTRADE AND/OR ITS REPRESENTATIVE(S), OR THE PURCHASER, INCLUDING
BUT NOT LIMITED TO THE IMPLIED WARRANTY OF MERCHANTABILITY AND THE
WARRANTY OF FITNESS FOR A PARTICULAR PURPOSE, ARE HEREBY EXPRESSLY
EXCLUDED AND DISCLAIMED BY ALLTRADE AND/OR ITS REPRESENTATIVES.
PURCHASER KNOWINGLY AND WILLINGLY WAIVES ANY AND ALL SUCH 
WARRANTIES AND RIGHTS, CLAIMS AND/OR CAUSES OF ACTION ARISING
THEREFROM OR BASED THEREON. PURCHASER’S SOLE AND EXCLUSIVE 
REMEDY IS AS STATED ABOVE.
Limitation Of Liability
IN NO EVENT SHALL ALLTRADE AND/OR ITS REPRESENTATIVE(S) BE LIABLE FOR
INDIRECT, INCIDENTAL, SPECIAL AND/OR CONSEQUENTIAL DAMAGES OF ANY
KIND ARISING OUT OF OR RELATED TO, DIRECTLY OR INDIRECTLY, ANY BREACH
OF ANY PROVISION OF ANY AGREEMENT BETWEEN ALLTRADE AND/OR ITS 
REPRESENTATIVE(S) AND PURCHASER, ANY WARRANTY HEREUNDER, 
AND/OR THE EXISTENCE, DESIGN, MANUFACTURE, PURCHASE, USE AND/OR
OPERATION OF ANY ITEM(S) SOLD HEREUNDER EVEN IF ALLTRADE AND/OR ITS
21 
						

							COMPONENT
#840056
19.2V BATTERY PACK 
INSTRUCTION MANUAL
87-1904-60957
KAWASAKI™ IS A TRADEMARK LICENSED BY KAWASAKI™
MOTORS CORP., U.S.A., WHICH DOES NOT MANUFACTURE OR 
DISTRIBUTE THIS PRODUCT. CONSUMER INQUIRES SHOULD BE
DIRECTED TO:
©COPYRIGHT 2006 ALLTRADE TOOLS, LLC.
1431 VIA PLATA
LONG BEACH, CA 90810-1462 USA
840056 – 19.2V Battery Pack_Rev 7/24/06
THIS MANUAL CONTAINS IMPORTANT INFORMATION REGARDING SAFETY, OPERATION, MAINTENANCE AND STORAGE OF THIS
PRODUCT. BEFORE USE, READ CAREFULLY AND UNDERSTAND ALL CAUTIONS, WARNINGS, INSTRUCTIONS AND PRODUCT
LABELS. FAILURE TO DO SO COULD RESULT IN SERIOUS PERSONAL INJURY AND/OR PROPERTY DAMAGE.
IF YOU SHOULD HAVE ANY QUESTIONS OR EXPERIENCE A PROBLEM WITH YOUR ALLTRADE PRODUCT, DO NOT RETURN THIS
PRODUCT TO THE STORE. PLEASE CALL OUR CUSTOMER SERVICE DEPARTMENT AT 1-800-590-3723. BEFORE YOU CALL,
HAVE THE FOLLOWING INFORMATION AVAILABLE: MODEL No., DATE PURCHASED AND STORE LOCATION. AN ALLTRADE 
REPRESENTATIVE CAN RESOLVE YOUR PROBLEM OVER THE PHONE. IF YOU WOULD LIKE TO MAKE A SUGGESTION OR 
COMMENT, GIVE US A CALL OR EMAIL US AT: [email protected]. YOUR FEEDBACK IS VITAL TO US.
FOR CUSTOMER SERVICE
POUR LE SERVICE APRÉS VENTE
OU DU CONSOMMATEUR
PARA EL SERVICIO
PARA EL CONSUMIDOR1-800-590-3723
Printed in China 
Imprimé dans la Chine 
Impreso en China 
						

							CAUTIONused without the safety alert symbol
indicates a potentially hazardous situation which,
if not avoided, may result in property damage.
NOTEprovides additional information that is useful
for proper use and maintenance of this tool. If a
NOTE is indicated make sure it is fully understood.
BATTERY
Before using battery pack, please read carefully all instruc-
tions and cautionarymarkings on battery pack, battery charg-
er and product using battery.
Do not incinerate the battery pack even if it is severely dam-
aged or is completely worn out.The battery pack can explode. 
Do not carry battery packs in aprons, pockets, or tool boxes, product kit
boxes, drawers, etc. with loose metal objects.battery pack terminals could
be short circuited causing damage to the battery pack, severe burns or fire.
The battery pack is Nickel-Cadmium (Ni-Cad) and is considered to be a toxic
material by the Environmental Protection Agency.Before disposing of dam-
aged or worn out Ni-Cad battery packs, check with your State Environmental
Protection Agency to find out about special restrictions on the disposal of these
battery packs, take them to your local recycling center for proper disposal, or
call 1-800-822-8837.
The battery is not fully charged. Before first use, the battery pack requires 
8-10 hours charge time to be fully charged. Subsequent recharging needs 3-5
hours for the battery to be fully charged. 
Always switch to a fresh battery when tool performance begins to diminish.
Severe heat is most destructive to a battery; the more heat generated, the faster
the battery loses power. A battery that gets too hot can have a shortened life. 
Never over-discharge a battery by using the tool even after tool performance
has decreased.Do not attempt to discharge a tool’s battery by continuing to
pull on the tool trigger. When tool performance begins to diminish, stop the tool
and recharge the battery for optimal performance.
CONGRATULATIONS!
Thanks for choosing this product. At Alltrade, our aim is to provide you with quality
products at an affordable price, and we want you to be totally satisfied with your
product and our Customer Service. If any help and advice is needed, please 
contact us at 1-800-590-3723. Properly cared for, this tool will give you many 
years of satisfaction.
INTENDED USE
This tool is intended for consumer use only. Your charger and/or adapter has been
designed for charging batteries of the type approved and supplied with this tool.
RECOGNIZE SAFETY SYMBOLS, WORDS AND LABELS
The safety instructions provided in this manual are not intended to cover all possible
conditions and practices that may occur when operating, maintaining and cleaning
power tools.
Always use common sense and pay particular attention to all the DANGER, 
WARNING, CAUTIONand NOTEstatements of this manual.
This is the safety alert symbol. It is used to alert
you to potential personal injury hazards. Obey all
safety messages that follow this symbol to avoid
possible injury or death.
DANGERindicates an imminently hazardous 
situation which, if not avoided, will result in death
or serious injury.
WARNINGindicates a potentially hazardous 
situation which, if not avoided, could result in
death or serious injury.
CAUTIONindicates a potentially hazardous 
situation which, if not avoided, may result in
minor or moderate injury.
12
® 
						

							PROTECTING THE ENVIRONMENT
BATTERIES
Alltrade batteries can be recharged many times. At the end of their useful life, recy-
cle batteries with due care for our environment. 
Ni-Cad and Ni-MH batteries are recyclable. Take them to your local recycling center
or call 1-800-822-8837. Collected batteries will be recycled or disposed of properly.
OTHER CONSUMER DO-IT-YOURSELF (DIY) TOOLS
Alltrade offers a full range of Kawasaki™ tools that make DIY jobs easy. If you would
like further information on the following products, please contact Alltrade Customer
Service Department at 1-800-590-3723. 
Cordless Drills/Screwdrivers
Impact Wrenches
Sanders
Jigsaws
Circular Saws
Angle Grinders
Reciprocating Saws
Routers
Rotary Tools
Corded and Cordless Multi-Purpose Tools
Wide Range of Accessories and more
4
Charge battery pack at ambient temperatures between 50° F – 104° F. 
Store tool and battery pack in locations where temperatures will not exceed
120°F. This is important to prevent serious damage to the battery cells.
The battery pack should always be recharged when the Cordless Drill begins to
run slowly. 
When battery pack is not in use, keep it away from other metal objects such as
paper clips, coins, keys, nails, screws or other small metal objects that can
make a connection from one terminal to another.Shorting the battery terminals
together may cause sparks, burns, or fire. 
SYMBOLS
IMPORTANT: Some of the following symbols may be used on your tool. Please
study them and learn their meaning. Proper interpretation of these symbols will
allow you to operate the tool better and safer.
SYMBOL NAME EXPLANATION
V Volts Voltage (Potential)A Amperes CurrentHz Hertz Frequency (Cycles per Second)W Watt PowerKg Kilograms Weight
Alternating Current Type of CurrentDirect Current Type of CurrentAlternating or Direct Current Type of CurrentEarthing Terminal Grounding TerminalClass II Construction Denotes Double Insulation
min Minutes Times Seconds Time

Diameter Size of Drill Bits, 
Grinding Wheels, etc.
No load speed No-load Rotational Speed
.../min Revolutions per Minute Revolutions, Surface Speed, 
Strokes, etc. per Minute
1,2,3, … Ring Selector Settings Speed, Torque or Position Settings
3