Barco Projector Toolset For Hdx Series Reference Guide

							7. Configurator, Projector alignment settings
Image 7-21
Black level adjustment
AC
B
Image 1Image 2
Image 7-22
ScenergiX, black level adjustment
R5905073 PROJECTOR TOOLSET 07/06/2011107 
						

							7. Configurator, Projector alignment settings
When Linked is checked, R, G and B are adjusted at the same time.
108R5905073 PROJECTOR TOOLSET 07/06/2011 
						

							8. Configurator, Projector adjustment settings
8. CONFIGURATOR, PROJECTOR
ADJUSTMENT SETTINGS
Overview
• Native resolution
• Window and Source selection
• Input setup
•Configuring an input slot
• Status PiP window
• Inputfiles
• Image settings
• Layout settings
8.1 Native resolution
What can be done
The aim here is to always show the resolution of the source independently of the resolution of the DMD
panels.
Image 8-1
When theshow native resolutionfunction is in the ON position, the projector handles the source as follows:
SourceProjected image
Name Ratio Resolution Ratio Resolution
XGA 4:3 1024x768 4:3 1024x768 image projected with
black borders
SXGA5:4 1280x1024 5:4 1280x1024 image projected with
black borders
SXGA+4:3 1400x1050 4:3 1400x1050 image projected with
black borders
R5905073 PROJECTOR TOOLSET 07/06/2011109 
						

							8. Configurator, Projector adjustment settings
SourceProjected image
UXGA4:3 1600x1200 4:3 1600x1200
part of the image
displayed, image scroll
possible
Black borders left and
right.
WUXGA16:10 1920x1200 16:10 1920x1200 normal image projected
How to set native resolution
1. Check the checkbox in front ofUse native resolution. (image 8-2)
Checked : image displayed in native resolution. The main source is displayed with its native resolution.
PiP is switched off.
Not checked : no native resolution used
Image 8-2
Set native resolution
WhenUse native resolutionis checked, some othermenus such as Aspect ratio, timings
are greyed out.
8.2 Window and Source selection
When a certain window is not visible in the layout pane, that means that the window is
disabled.
What can be done?
The active window can be selected by clicking on a window in the window layout preview or by selecting
a window button.
The projectors can have a main window and a PiP (picture in picture) window.
110
R5905073 PROJECTOR TOOLSET 07/06/2011 
						

							8. Configurator, Projector adjustment settings
Window selection
1. Click on the corresponding window in the window layout preview (a1)
Or,
click on the desired window name in theSelection - Window - Slot - Inputpane (a2). (image 8-3)
In the layout preview pane, the white square with 6 selection points is placed around the selected win-
dow.
In theSelection - Window - Slot - Inputpane, the background of the selected window button becomes
light blue.
Image 8-3
Window selection
Slot - input selection
1. In theSelection - Window - Slot - Inputpane, click on the combo next to the desired window and select
the desired input slot. (image 8-4)
R5905073 PROJECTOR TOOLSET 07/06/2011
111 
						

							8. Configurator, Projector adjustment settings
Image 8-4
Slot selection
8.3 Input setup
What can be done ?
Each inserted input must be configured for a specific source before it can be used.
How to configure
1. Click onInput setup(1).
The input setup dialog box opens (2). (image 8-5)
2. To select an input, click on the radio button of your choice (3).
The second column shows immediately the input type (4).
The third column shows the possible configurations for that type of input (5).
3. Select the correct source type for the selected input.
112
R5905073 PROJECTOR TOOLSET 07/06/2011 
						

							8. Configurator, Projector adjustment settings
Image 8-5
Input setup
DVI input
Image 8-6
DVI sources
The following sources are possible:
• DVI mode single link
• RGB analog hs-vs
• YUV analog hs-vs
• DVI mode dual link
R5905073 PROJECTOR TOOLSET 07/06/2011
113 
						

							8. Configurator, Projector adjustment settings
SDI input
Image 8-7
As the SDI input contains 2 inputs, start by selecting the input :
• Input 1 (SD, HD or 3G)
• Input 2 (SD, HD or 3G)
• Input 1 priority over input 2 (SD, HD or 3G)
• Input 2 priority over input 1 (SD, HD or 3G)
• Dual HDSDI (uses both inputs)
Then, select the standard for the selected SDI input. The following standards are possible:
• 4:2:2-YCbCr-10
• 4:4:4-YCbCr-10
• 4:4:4-RGB-10
• 4:4:4-YCbCr-12
• 4:4:4-RGB-12
• 4:4:2-YCbCr-12
When a dual input is used, select the mode:
• Dual normal
•Dualswaplinks
For 3G source, select the 3G setting
•3GDualHD
• 3G Direct Mapping
114
R5905073 PROJECTOR TOOLSET 07/06/2011 
						

							8. Configurator, Projector adjustment settings
5 cable input
Image 8-8
The following sources are possible:
• RGB HS/VS-CS
•RGBCV
•RGBSOG
• YUV HS/VS-CS
•YUVCV
•YUVSOV
•CVBS
•S-Video
•RGBAUTO
• CVBS/S-VIDEO AUTO
8.4 Configuring an input slot
What should be done?
Some input modules can accept different sources. The projector must know which type of source is con-
nected to the input.
This configuration is the same as clicking onInput setup.
How to configure
1. Select the window for which the input must be configured (a1, a2). (image 8-9)
2. Click onAdjust(b).
TheInputdialog box opens.
3. Click onSettingsand selectInput mode. (image 8-10)
TheInput modedialog box opens with the current active settingfilled out.
4. Click on the combo box next toInput modeand select the correct setting.
5. ClickCloseto return.
R5905073 PROJECTOR TOOLSET 07/06/2011
115 
						

							8. Configurator, Projector adjustment settings
Image 8-9
Open the adjustment mode
116R5905073 PROJECTOR TOOLSET 07/06/2011