Black and Decker Spacemaker Can Opener CO100 CO100WM CO100B CO95 User Manual

							

Models 
Modelos
❑	CO100
❑	CO100WM
❑	CO100B
❑	CO95
USA/Canada	 1-800-231-9786
www.prodprotect.com/applica
Accessories/Parts	(USA/Canada)
Accesorios/Partes	(EE.UU/Canadá)
1-800-738-0245
Please	 Read	and	Save	 this	Use	 and	Care	 Book
Por	favor	 lea	este	 instructivo	 antes	de	usar	 el	producto
U N D E R - T H E - C A B I N E T 
CAN  OPENER
ABRELATAS
PARA  INSTALAR DEBAJO  DEL  GABINETE
Register your product online at  www.prodprotect.com/applica, for a chance to  WIN $100,000! For US residents only
Registre su producto por Internet en  www.prodprotect.com/applica y tendrá la oportunidad de GANAR $100,000! Solamente para residentes de EE.UU
™
† 
						

							



IMPORTANT	SAFEGUARDS
 When using electrical appliances, basic safety precautions should always 
be followed, including the following:
❑ Read all instructions.
❑ To protect against risk of electrical shock do not immerse cord, plugs or 
appliance in water or other liquid.
❑ Close supervision is necessary when any appliance is used by or near 
children.
❑ Make sure appliance is OFF when not in use, before putting on or taking 
off parts, and before cleaning.
❑ Avoid contacting moving parts. 
❑ Do not operate any appliance with a damaged cord or plug or 
after the appliance malfunctions, or is dropped or damaged in any 
manner. Return appliance to the nearest authorized service facility for 
examination, repair or electrical or mechanical adjustment. Or, call the 
appropriate toll-free number on the cover of this manual.
❑ The use of attachments not recommended or sold by the manufacturer 
may cause fire, electric shock or injury.
❑ Do not use outdoors.
❑ Do not open pressurized (aerosol-type) cans.
❑ Do not open cans of flammable liquids such as lighter fluids.
❑ To reduce the risk of fire or electric shock, do not operate any heating 
appliance beneath the mounted unit.
❑ Do not mount the storage bracket/unit over or near any portion of a 
heating or cooking appliance, or a sink or basin.
SAVE	THESE	 INSTRUCTIONS.
This	product	is	for	household	use	only.
POLARIZED 	PLUG 	(  0V 	Models 	Only)
This appliance has a polarized plug (one blade is wider than the other). To reduce the 
risk of electric shock, this plug is intended to fit into a polarized outlet only one way. If 
the plug does not fit fully into the outlet, reverse the plug. If it still does not fit, contact a 
qualified electrician. Do not attempt to modify the plug in any way.
TAMPER-RESISTANT	 SCREW
Warning:	This	appliance	 is	equipped	 with	a	tamper-resistant	 screw	to	prevent	
removal	 of	the	 outer	 cover.	 To	reduce	 the	risk	 of	fire	 or	electric	 shock,	do	not	
attempt	 to	remove	 the	outer	 cover.	 There	are	no	user-serviceable	 parts	inside.	
Repair	 should	 be	done	 only	by	authorized	 service	personnel.
ELECTRICAL	 CORD
a) A short power-supply cord (or detachable power-supply cord) is to be provided 
to reduce the risk resulting from becoming entangled in or tripping over a 
longer cord.
b) Longer detachable power-supply cords or extension cords are available and 
may be used if care is exercised in their use.
c) If a long detachable power-supply cord or extension cord is used,
  1) The marked electrical rating of the detachable power-supply cord  
    or extension cord should be at least as great as the electrical rating of the  
   appliance,
 2)  If the appliance is of the grounded type, the extension cord should be  
    a grounding-type 3-wire cord, and
 3)  The longer cord should be arranged so that it will not drape over the  
    countertop or tabletop where it can be pulled on by children or  
   tripped over.
Note:	If the power supply cord is damaged, it should be replaced by qualified 
personnel; in Latin America, by an authorized service center. 
						

							



Product	may	vary	 slightly	 from	what	 is	illustrated.
	 .	 Bag 	cutter
	 .	 Knife 	sharpener
	 .	 Bottle 	opener
	 .	 Cover
†	 .	 Blade 	assembly 	with 	magnet 	(Part 	# 	CO00 )	(White), 	(Part 	# 	CO00 )	(Black)
	 6.	 Locating 	post
	 7.	 Piercing 	lever
	 8.	 Cord 	storage 	(not 	shown)
	 9.	 Cord 	management 	hook 	(not 	shown)
†	 0.	 Mounting 	Kit 	(Part 	# 	CO00 -0 )	White, 	(Part 	# 	CO00 -0 )	Black	(not 	shown)
Note: 	† 	indicates consumer replaceable/removable parts







A
†	 .	 Mounting 	Parts		 	 (Part 	# 	SDC-MOUNTING 	KIT)
	 	A.	 6	Spacers		 	 	 				½"		 	 					¼"		 	 					/6"		 	 	 				/6"
	 	B.		 Screws		 	 	 				"		 	 					½"		 	 					¼"
	 	C.		Washers
	 .	 Mounting 	Template 	(in 	box)
You 	will 	also 	need:
•	 Tape
•	 Ruler 	(or 	you 	may 	cut 	out 	the 	ruler 	provided 	on 	the 	template)
•	 Electric 	drill 	with 	a 	¼” 	drill 	bit
A
A
C
B 
						

							
6
7

Note: If you are connecting this appliance to the receptacle of another 
†SpaceMaker™ appliance such as the toaster oven or coffeemaker, make sure you 
can easily unplug the appliance following use.
DETERMINE	CABINET	TYPE
Prior to installation, determine if your cabinet has a flat bottom (B) or an 
overhang molding (C). If your cabinet is flat, follow STANDARD INSTALLATION; 
if the cabinet has an overhang molding, refer to OVERHANG MOLDING 
INSTALLATION.
STANDARD	 INSTALLATION	 (FLAT	CABINET)
Important:	 Always	wear	protective	 glasses	or	goggles	 to	prevent	 injury	when	
drilling.
1. Clear countertop under installation area to avoid getting dust or debris on other 
appliances or items. Open cabinets and remove contents to make mounting 
easier.
2. Clean both the underside and topside of the bottom panel of the cabinet.
3. With cabinet doors open, place mounting template flush against the surface of 
the underside of your cabinet, making sure to align thick line on template with 
bottom front edge of your cabinet (D).
Important:	 Do	not	 align	 screw	 holes	on	template	 directly	under	the	partition	
between	 cabinets,	 as	this	 will	 prevent	 you	from	 installing	 the	appliance	 properly.	
Pay	close	 attention	 to	where	 the	drill	 holes	 will	be	set	 so	as	not	 to	damage	 your	
cabinets	 during	mounting.	 Drilling	through	 your	cabinet’s	 partition	may	cause	
damage	 to	cabinets	 and	prevent	 proper	installation.
4. Fold the template along the edge of your cabinet so the thick line is straight 
with bottom front edge; pull template tight and tape down to hold in place.
GETTING	 STARTED	
• Remove all packing material, labels and any stickers.
• Remove and save literature.
• Unpack mounting parts and set them aside in a safe place where they will not 
roll away or get lost.
Important:	 Do	not	 attempt	 to	operate	 appliance	 until	it	is	 properly	 installed.
CHOOSE	 A	LOCATION
When choosing your location, consider the following:
• DO make sure to mount within reach of an electrical outlet.
• DO consider your normal work patterns in the kitchen when choosing 
location.
• DO	 NOT mount over any heating or cooking appliance such as your range or 
oven.
• DO	NOT mount over or near a sink.
• DO	NOT	mount under, in front of or behind any under-cabinet light fixtures.
Note:	If mounting multiple †SpaceMaker™ appliances and you are installing your 
appliance next to the SpaceMaker™ oven (Fig.	 A.):
• Allow at least 1” between the control panel side of the oven and the appliance. 
• Allow at least 4” between the side opposite the control panel of your oven and 
adjacent wall or other appliance. You can mount the other appliances flush to 
one another. 
BC
D
A.
4”1”
4”
1” 
						

							
8
9

Note: If you are connecting this appliance to the receptacle of another 
†SpaceMaker™ appliance such as the toaster oven or coffeemaker, make sure you 
can easily unplug the appliance following use.
13. Your †SpaceMaker™ appliance is now ready for use!
OVERHANG	 MOLDING	INSTALLATION	
For	cabinets	 with	an	overhang	 molding	(see	Illustration	 C)
Important:	Always	wear	protective	 glasses	or	goggles	 to	prevent	 injury	when	
drilling.
Note:	Spacers are provided in case your cabinet has an overhang molding at the 
front edge. Only use spacers on the rear screws of the appliance to ensure it is 
level with the front.
1. Clear countertop under installation area to avoid getting dust or debris on other 
appliances or items. Open cabinets and remove contents to make mounting 
easier.
2. Clean both the underside and topside of the bottom panel of the cabinet.
3. Using a ruler, measure the thickness of the overhang molding (G), accurately 
noting the number for use in the following step.
Note: If you do not have a ruler, you may cut out the paper ruler provided on the 
edge of your mounting template.
4. After measuring the overhang molding thickness as shown in Illustration G, look 
at the dashed lines on the mounting template; each line has a measurement 
next to it that indicates the thickness of the overhang molding used with that 
line. For example, if your cabinet has an overhang molding thickness of ½”, 
you will use the ½” dashed line on the template. 
  5.  Fold the template along the dashed line that matches the thickness of your 
overhang molding.
  6. Place the folded template against the back edge of the overhang molding, 
making sure the side with the drill hole marks is facing down (H).
5. Drilling from under the cabinet up, drill holes through the 4 places marked on 
the template, using a ¼-inch drill bit (E).
Important:	 Always	ensure	you	are	drilling	 straight	 up	through	 the	marked	
mounting	 holes	on	the	 template.	 Drilling	at	an	 angle	 may	prevent	 proper	
installation	 and	may	 damage	 cabinets	 if	the	 drill	 bit	pierces	 the	partition.
  6. Once holes are drilled, remove tape and mounting template.
  7. Wipe dust and debris off the topside and underside of the cabinet surface.
  8. Place a washer inside the cabinet over each of the 4 holes you drilled.
  9. Hold appliance in place, aligning front of unit with front edge of cabinet; 
drilled holes on cabinet should be aligned with mounting holes on the unit.
10. Drop one of your screws through each of the washers covering the holes in the 
cabinet, from inside the cabinet down.
Note: To determine which screws to use, you must have enough of the screw 
exposed underneath the cabinet to properly thread the screw into the nut. 
11. Screwing from inside the cabinet down into appliance holes, tighten 4 screws 
in place to secure appliance to cabinet.
Note: Always tighten screws to ensure the appliance does not move or shake 
during operation.
12. Pull out cord from cord storage behind appliance and plug into standard 
electrical outlet. Extra cord can be fed back into storage or hung over cord 
management hook behind unit (F).
F
G
E
H 
						

							
0


Note: To determine which screws to use, you must have enough of the screw 
exposed underneath the cabinet to properly thread the screw into the nut.
14. Place the appropriate number of spacers determined in step 12 on both of the 
rear screws to ensure the appliance will be even (L).
Note:	If the height of your overhang molding is too tall to be accommodated by 
the number of spacers provided, you may call, toll-free, at 1-800-231-9786 to 
order additional spacers at no charge.
Note: For spacer installation, you may require assistance in mounting in order to 
hold spacers in place while securing the appliance at the same time. If assistance 
is not available, use a small clamp to hold the spacers in place while you position 
the appliance.
15. Once spacers are set, hold appliance up and tighten screws to secure. Screw 
from inside the cabinet down. 
Note: Always tighten screws to ensure the appliance does not move or shake 
during operation.
16. Pull out cord from cord storage behind appliance and plug into standard 
electrical outlet. Extra cord can be fed back into storage or hung over cord 
management hook behind unit (see	 illustration	 F).
Note: If you are connecting this appliance to the receptacle of another 
†SpaceMaker™ appliance such as the toaster oven or coffeemaker, make sure you 
can easily unplug the appliance following use.
17. Your †SpaceMaker™ appliance is now ready for use!
Important:	 Do	not	 align	 screw	 holes	on	template	 directly	under	the	partition	
between	 cabinets,	 as	this	 will	 prevent	 you	from	 installing	 the	appliance	 properly.	
Pay	close	 attention	 to	where	 the	drill	 holes	 will	be	set	 so	as	not	 to	damage	 your	
cabinets	 during	mounting.	 Drilling	through	 your	cabinet’s	 partition	may	cause	
damage	 to	cabinets	 and	prevent	 proper	installation.
  7. Making sure to keep the fold line straight against the back edge of the 
overhang molding, tape the template securely in place.
  8. Drilling from under the cabinet up, drill holes through the 4 places marked on 
the template using a ¼-inch drill bit (J).
Important:	 Always	ensure	you	are	drilling	 straight	 up	through	 the	marked	
mounting	 holes	on	the	 template.	 Drilling	at	an	 angle	 may	prevent	 proper	
installation	 and	may	 damage	 cabinets	 if	the	 drill	 bit	pierces	 the	partition.
  9. Once holes are drilled, remove tape and mounting template.
10. Wipe dust and debris off the underside and topside of the cabinet surface.
11. Place a washer inside the cabinet over each of the 4 holes you drilled.
12. Now, use your ruler or the paper ruler provided to measure the overhang 
molding height, placing your ruler vertically against the underside of the 
cabinet behind the overhang molding. This number determines the number of 
spacers you need, using a number of spacers equal to the overhang molding 
height. For example, a 1” overhang molding would use 2, ½” spacers on each 
of the rear holes	(K).
13.  Drop one of your screws through each of the washers covering the holes in the 
cabinet, from inside the cabinet down.
J
L
K 
						

							



How	to	Use
This appliance is for household use only.
OPENING	 A	CAN
1.  Lift piercing lever.
2. Tip can so that the rim is under the locating post, then push down on the piercing 
lever, making sure the cutter blade is inside the rim of the can (M).
Note:	Because of the hands-free feature, it is not necessary to hold the lever down 
or hold the can during cutting. However, you may have to support very tall or heavy 
cans.
Tip: When the can is opened, the can opener will stop automatically.
3. To remove the can, hold it with one hand and raise the lever with the other.
Caution:	 Avoid	contact	 with	the	cut	edges	 of	the	 can	 or	lids	 —	they	 are	sharp.	 During	
opening	 process,	 the	design	 of	your	 can	opener	 will	roll	the	rim	 of	the	 can	 to	prevent	
sharp	 edges;	 however,	 handle	with	caution	 and	always	 handle	 cut	lid	with	 caution,	 as	
these	edges	 are	not	 rolled.
4. Carefully discard the lid from the magnet.
Important	 Tips:
 • Do not use this can opener to open cans with a pull tab, peel-off foil seal,  
    or rolling key or rimless cans.
 • Open frozen juices or foods in cardboard cans right from the freezer, while they  
    are frozen. 
 • Aluminum lids will not stick to the magnet.
M
USING	 THE	KNIFE	 SHARPENER
1. For best results, sharpen the entire blade length in one continuous stroke. 
2. Insert blade to be sharpened with the end of the blade closest to the handle on the 
knife into the sharpening slot. 
3. Carefully press down on the blade and pull it toward you through the slot in one 
continuous stroke (N).
Important:	 Do	not	 saw	 knife	 back	and	forth	 to	sharpen.	 Pull	through	 the	sharpener	
in	one	 direction	 with	a	continuous,	 slow,	even	motion.	 Failure	to	do	 so	may	 dull	or	
damage	 your	blade.
4. Repeat until desired sharpness is achieved.
5. Wash and dry knife before using again.
Important	 Tips:
 • Use caution when washing and drying knives after sharpening.
 • Do not sharpen serrated blades, as this will smooth their edges.
 • Do not sharpen scissors.
USING	 THE	BOTTLE	 OPENER
1. Grasp the bottle and position cap above the lip on the back side of the bottle 
opener. 
2. Tilt bottom of the bottle away from you to catch the cap on the lip and open the 
bottle (P).
N
P 
						

							



USING	THE	BAG	 CUTTER
1. Grasp the plastic or metal foil bag to be opened by one corner, with one hand 
holding the top edge and the other holding the side or bottom, depending on the 
size of the bag.
2. Position tightly pulled corner of bag against the cutter and pull firmly to the left to 
open the bag (Q).
Note: Pulling a bag straight against the cutter will cut a line along the top of the bag; 
pulling at an angle will simply remove the corner.
Q
Care	 and	Cleaning
This product contains no user serviceable parts. Refer service to qualified service 
personnel.
Important:	 Unplug	the	cord	 before	 cleaning	 the	unit.
REMOVING	 BLADE	ASSEMBLY
1. Lift the piercing lever up as far as it will go (roughly 90°).
2. Carefully grip the blade assembly and pull it away from the can opener (R).
3. Wash in sudsy water by hand and dry thoroughly. Do not put the blade assembly in 
the dishwasher.
4. Before replacing the blade assembly, wipe the can opener body, knife sharpener 
and area around the geared wheel with a slightly damp cloth or sponge.
REPLACING	 BLADE	ASSEMBLY
1. Align key post on the blade assembly with key slot on the unit (S).
2. Push in blade assembly and turn clockwise until it locks into position (T).
R
S
T 
						

							
6
7

INSTRUCCIONES	IMPORTANTES	
DE	SEGURIDAD
Cuando se usan aparatos eléctricos, siempre se deben respetar las 
siguientes medidas básicas de seguridad:
❑ Por favor lea todas las instrucciones.
❑ A fin de protegerse contra el riesgo de un choque eléctrico, no sumerja 
el cable, los enchufes ni el aparato en agua ni en ningún otro líquido.
❑ Todo aparato eléctrico usado en la presencia de los niños o por ellos 
mismos requiere la supervisión de un adulto.
❑ Desconecte el aparato del tomacorriente cuando no esté en uso, antes 
de instalarle o retirarle piezas y antes de limpiarlo.
❑ Evite el contacto con las piezas móviles. 
❑ No use ningún aparato eléctrico que tenga el cable o el enchufe 
averiado, que presente un problema de funcionamiento o que esté 
dañado. Acuda a un centro de servicio autorizado para que lo 
examinen, reparen o ajusten o llame gratis al número correspondiente 
en la cubierta de este manual. 
❑ El uso de accesorios no recomendados por el fabricante del aparato 
puede ocasionar incendio, choque eléctrico o lesiones.
❑ No use este aparato a la intemperie.
❑ No abra latas (tipo aerosol) presurizadas. 
❑ No abra latas de líquidos inflamables tales como las de los líquidos 
encendedores.
❑ Para evitar el riesgo de incendio o choque eléctrico, no opere ningún 
artefacto de calefacción debajo del montaje de este aparato.
❑ No instale el soporte de almacenaje / aparato sobre ni cerca de ninguna 
superficie de un aparato de calentar o de cocina ni sobre una pila o 
fregadero.
CONSERVE	 ESTAS	
INSTRUCCIONES.
Este	aparato	eléctrico	es	para	uso	doméstico	únicamente.
ENCHUFE	POLARIZADO 	(Solamente 	para 	los 	modelos 	de 	 0V)
Este aparato cuenta con un enchufe polarizado (un contacto es más ancho que el 
otro). A fin de reducir el riesgo de un choque eléctrico, este enchufe encaja en un 
tomacorriente polarizada en un solo sentido. Si el enchufe no entra en el tomacorriente, 
inviértalo y si aun así no encaja, consulte con un electricista. Por favor no trate de 
alterar esta medida de seguridad.
TORNILLO	 DE	SEGURIDAD
Advertencia:	 Este	aparato	 cuenta	con	un	tornillo	 de	seguridad	 para	evitar	
la	remoción	 de	la	cubierta	 exterior	del	mismo.	 A	fin	 de	reducir	 el	riesgo	 de	
incendio	 o	de	 choque	 eléctrico,	 por	favor	 no	trate	 de	remover	 la	cubierta	
exterior.	 Este	producto	 no	contiene	 piezas	reparables	 por	el	consumidor.	
Toda	 reparación	 se	debe	 llevar	 a	cabo	 únicamente	 por	personal	 de	servicio	
autorizado.
CABLE	 ÉLECTRICO
a) El producto se debe de proporcionar con un cable eléctrico corto (o uno 
separable), a fin de reducir el riesgo de tropezar o de enredarse en un cable 
más largo.
b) Existen cables eléctricos más largos y separables o cables de extensión que uno 
puede utilizar si toma el cuidado debido.
c) Si se utiliza un cable separable o de extensión,
  1) El régimen nominal del cable separable o del cable de extensión debe ser,  
    como mínimo, igual al del régimen nominal del aparato.
 2)  Si el aparato es de conexión a tierra, el cable de extensión debe ser un  
    cable de tres alambres de conexión a tierra.
 3)  Uno debe de acomodar el cable más largo de manera que no cuelgue del  
    mostrador o de la mesa, para evitar que un niño tire del mismo o que  
   alguien se tropiece.
Nota:	Si el cordón de alimentación es dañado, en América Latina debe sustituirse 
por personal calificado o por el centro de servicio autorizado. 
						

							
8
9

El	producto	 puede	variar	ligeramente	 del	que	 aparece	 ilustrado	 aquí.	
	.	 Cortabolsas
	 .	 Afilador 	de 	cuchillos
	 	 .	 Compartimiento 	para 	el 	cable
	 .	 Tapa
†	 .	 Montaje 	de 	la 	cuchilla, 	con 	magneto 	(Pieza 	Nº 	C00 )	blanco, 	(Pieza 	Nº 	C00 )	negro
	 6.	 Guía 	de 	colocación
	 7.	 Palanca 	de 	perforación
	 8.	 Compartimiento 	para 	el 	cable 	(no 	mostrado)
	 9.	 Gancho 	para 	afianzar 	el 	cable 	(no 	mostrado)
†	 0.	 Juego 	de 	piezas 	de 	montaje 	(Pieza 	Nº 	C00 -0 )	blanco, 	(Pieza 	Nº 	C00 -0 )	negro			 	 (no 	mostrado)
Nota: 	† 	indica piezas desmontables/reemplazables por el consumidor







A†	 .	 Piezas 	para 	el 	ensamblaje		 	 (Pieza 	Nº 	SDC-MOUNTING 	KIT)
	 	A.	 6	Separadores	 	 				½"		 					¼"		 					/6"		 	 				/6"
	 	B.	 	 Tornillos	 	 				"		 					½"		 					¼"
	 	C.		Arandela
	.	 Plantilla 	para 	el 	ensamblaje 	(en 	caja)
También 	necesitará:	
•	 Cinta 	adhesiva
•	 Regla 	(o 	puede 	también 	cortar 	la 	regla 	que 	se 	proporciona 	con 	la 	plantilla)
•	 Taladro 	eléctrico 	con 	broca 	de 	¼”	
A
C
B
A