Brother 8460 N Manual

							Section IV
SoftwareIV
Software and Network features82 
						

							82
13
The User’s Guide on the CD-ROM includes 
the Software User’s Guide and Network 
User’s Guide for features available when 
connected to a computer (for example, 
Printing and Scanning).
„Printing
(For Windows
®, see Chapter 1 in the 
Software User’s Guide on the CD-ROM.)
(For Macintosh
®, see Chapter 7 in the 
Software User’s Guide on the CD-ROM.)
„Scanning
(For Windows
®, see Chapter 2 in the 
Software User’s Guide on the CD-ROM.)
(For Macintosh
®, see Chapter 8 in the 
Software User’s Guide on the CD-ROM.)
„ControlCenter2 
(For Windows
®, see Chapter 3 in the 
Software User’s Guide on the CD-ROM.)
(For Macintosh
®, see Chapter 9 in the 
Software User’s Guide on the CD-ROM.)
„Remote Setup
(For Windows
®, see Chapter 5 in the 
Software User’s Guide on the CD-ROM.)
(For Macintosh
®, see Chapter 11 in the 
Software User’s Guide on the CD-ROM.)
„Brother PC-FAX
(For Windows
®, see Chapter 6 in the 
Software User’s Guide on the CD-ROM.)
(For Macintosh
®, see Chapter 7 in the 
Software User’s Guide on the CD-ROM.)
„LDAP
(See the Network User’s Guide on the CD-
ROM.)
„Network Faxing
(See the Network User’s Guide on the CD-
ROM.)„Network Printing
(See the Network User’s Guide on the CD-
ROM.)
„Network Scanning
(For Windows
®, see Chapter 4 in the 
Software User’s Guide on the CD-ROM.)
(For Macintosh
®, see Chapter 10 in the 
Software User’s Guide on the CD-ROM.)
„Wireless Network Users (MFC-8870DW 
only)
(For details on connecting your machine 
to a wireless Network, see the Quick 
Setup Guide and Network Users Guide 
on the CD-ROM.)
Note
See Accessing the complete User’s Guide 
on page 2.
 
Software and Network features13 
						

							Section V
AppendicesV
Safety and Legal84
Options93
Troubleshooting and routine maintenance95
Menu and Features129
Specifications148
Glossary160 
						

							84
A
Choosing a locationA
Place your machine on a flat, stable surface that is free of vibration. Put the machine near a 
telephone socket and a standard, grounded electrical socket. Choose a location where the 
temperature remains between 10° and 32.5° C.
„Make sure cables leading to the machine do not constitute a trip hazard.
„Avoid placing your machine on the carpet.
„Do not place near heaters, air conditioners, water, chemicals, or refrigerators.
„Do not expose the machine to direct sunlight, excessive heat, moisture, or dust.
„Do not connect your machine to electrical sockets controlled by wall switches or automatic 
timers, or to the same circuit as large appliances that might disrupt the power supply.
„Avoid sources of interference, such as speakers, or the base units of cordless phones.
Safety and LegalA
    
						

							Safety and Legal
85
Important InformationA
Safety precautionsA
Please read these instructions before attempting any maintenance, and keep them for later 
reference. When using your telephone equipment, follow basic safety precautions to reduce the 
risk of fire, electric shock or personal injury.
„Do not use this product near water, or in a damp environment.
„Avoid using this product during an electrical storm. There may be a remote risk of electric 
shock from lightning.
„We do not advise using an extension lead.
„Never install telephone wiring during a lightning storm. Never install a telephone wall socket in 
a wet location. 
„If any cables become damaged, disconnect your machine, and contact your Brother dealer.
„Do not place any objects on the machine, or obstruct the air vents.
„Do not use flammable substances near the machine.
Doing this might cause a fire or electrical shock.
„This product should be connected to an adjacent grounded AC power source within the range 
indicated on the rating label. Do NOT connect it to a DC power source. If you are not sure, 
contact a qualified electrician.
„Do not dispose of batteries in a fire. They may explode. Check with local codes for possible 
special disposal instructions. 
						

							86
WARNING 
Before cleaning the inside of the machine, first 
unplug the telephone line cord, and then the power 
cord from the electrical socket.
 
Do not handle the plug with wet hands. Doing this might 
cause an electrical shock.
 
After you have just used the machine, some internal 
parts of the machine will be extremely hot. When you 
open the front or back cover of the machine, 
DO NOT touch the shaded parts shown in the 
illustration.
 
The fuser unit is marked with a caution label. DO 
NOT remove or damage the label. 
To prevent injuries, be careful not to put your hands on 
the edge of the machine under the document cover as 
shown in the illustration.
  
						

							Safety and Legal
87
 
To prevent injuries, DO NOT put your fingers in the area 
shown in the illustrations.
 
DO NOT use a vacuum cleaner to clean up scattered toner. Doing this might cause the toner 
dust to ignite inside the vacuum cleaner, potentially starting a fire. Please carefully clean the 
toner dust with a dry, lint-free cloth and dispose of it according to local regulations.
If moving your machine, use the handholds 
provided. First making sure to disconnect any 
cables.
  
						

							88
IEC 60825-1 SpecificationA
This machine is a Class 1 laser product as defined in IEC 60825-1 specifications. The label shown 
below is attached in countries where required.
Laser DiodeA
Wave length:  770 - 810 nm
Output: 5 mW max.
Laser Class:  Class 3B
WARNING 
Use of controls, adjustments or performance of procedures other than those specified in this 
manual may result in hazardous radiation exposure.
 
Disconnect deviceA
This product must be installed near an electrical socket that is easily accessible. In case of 
emergency, you must disconnect the power cord from the electrical socket to shut off power 
completely.
Wiring informationA
If you need to replace the plug fuse, fit a fuse that is approved by ASTA to BS1362 with the same 
rating as the original fuse.
Always replace the fuse cover. Never use a plug that does not have a cover. If in any doubt, call 
a qualified electrician. Warning - This printer must be earthed.
The wires in the mains lead are coloured in line with the following code:
„Green and Yellow: Earth
„Blue: Neutral
„Brown: Live This machine has a Class 3B Laser Diode which emits invisible 
laser radiation in the Scanner Unit. The Scanner Unit should not 
be opened under any circumstances.
 
CLASS 1 LASER PRODUCT
APPAREIL À LASER DE CLASSE 1
LASER KLASSE 1 PRODUKT 
						

							Safety and Legal
89
LAN connectionA
CAUTION 
DO NOT connect this product to a LAN connection that is subject to over-voltages.
 
Radio interferenceA
This product complies with EN55022 (CISPR Publication 22)/Class B. When connecting the 
machine to a computer, ensure that you use the following interface cables.
1 A shielded parallel interface cable with twisted-pair conductors and that is marked IEEE 1284 
compliant. The cable must not exceed 2.0 metres in length.
2 A USB cable which must not exceed 2.0 metres in length.
International ENERGY STAR® Compliance StatementA
The purpose of the International ENERGY STAR® Program is to promote the development and popularization 
of energy-efficient office equipment.As an E
NERGY STAR® Partner, Brother Industries, Ltd. has determined 
that this product meets the E
NERGY STAR® guidelines for energy efficiency.
 
EU Directive 2002/96/EC and EN50419A
 
This equipment is marked with the above recycling symbol. It means that at the end of the life of 
the equipment you must dispose of it separately at an appropriate collection point and not place 
it in the normal domestic unsorted waste stream. This will benefit the environment for all. 
(European Union only) 
						

							90
Important safety instructionsA
1 Read all of these instructions.
2 Save them for later reference.
3 Follow all warnings and instructions marked on the product.
4 Unplug this product from the wall socket before cleaning inside of the machine. Do not use 
liquid or aerosol cleaners. Use a damp cloth for cleaning.
5 Do not place this product on an unstable cart, stand, or table. The product may fall, causing 
serious damage to the product.
6 Slots and openings in the cabinet at the back or bottom are provided for ventilation. To ensure 
reliable operation of the product and to protect it from overheating, these openings must not 
be blocked or covered. The openings should never be blocked by placing the product on a bed, 
sofa, rug, or other similar surface. This product should never be placed near or over a radiator 
or heater. This product should never be placed in a built-in installation unless adequate 
ventilation is provided.
7 This product should be connected to an AC power source within the range indicated on the 
rating label. Do NOT connect it to a DC power source. If you are not sure, contact a qualified 
electrician.
8 This product is equipped with a 3-wire grounded plug. This plug will only fit into a grounded 
power outlet. This is a safety feature. If you are unable to insert the plug into the outlet, call 
your electrician to replace your obsolete outlet. Do not defeat the purpose of the grounded 
plug.
9 Use only the power cord supplied with this machine.
10 Do not allow anything to rest on the power cord. Do not place this product where people can 
walk on the cord.
11 Do not place anything in front of the machine that will block received faxes. Do not place 
anything in the path of received faxes.
12 Wait until pages have exited the machine before picking them up.
13 Unplug this product from the power socket and refer all servicing to Brother Authorized Service 
Personnel under the following conditions:
„When the power cord is damaged or frayed.
„If liquid has been spilled into the product.
„If the product has been exposed to rain or water.
„If the product does not operate normally when the operating instructions are followed. 
Adjust only those controls that are covered by the operating instructions. Incorrect 
adjustment of other controls may result in damage and will often require extensive work by 
a qualified technician to restore the product to normal operation.
„If the product has been dropped or the cabinet has been damaged.
„If the product exhibits a distinct change in performance, indicating a need for service.