Brother 8460 N Manual

							Receiving a fax
41
6
Receive Mode settings6
Ring Delay6
The ring delay sets the number of times the 
machine rings before it answers in Fax Only 
and Fax/Tel modes.
If you have external or extension phones on 
the same line as the machine or subscribe to 
the BT Call Sign
 1 service, keep the Ring 
Delay setting of 4. (See Operation from 
extension telephones on page 49 and Fax 
Detect on page 42.)
1BT Call Sign is for U.K. only.
aMake sure you are in Fax mode  .
bPress Menu, 2, 1, 1. 
21.Setup Receive
1.Ring Delay
a03
b04
Select 
ab & OK
cPress a or b to select how many times 
the line rings before the machine 
answers. Press OK.
dPress Stop/Exit.
F/T Ring Time6
When somebody calls your machine, you and 
your caller will hear the normal telephone ring 
sound. The number of rings is set by the ring 
delay setting. 
If the call is a fax, then your machine will 
receive it; however, if it is a voice call the 
machine will sound the F/T ring (a fast 
double-ring) for the time you have set in the 
F/T ring time setting. If you hear the F/T ring 
it means that you have a voice caller on the 
line.
Because the F/T ring is made by the machine, 
extension and external telephones will not 
ring; however, you can still answer the call on 
any telephone. For more information see 
Using remote codes on page 50.
aMake sure you are in Fax mode  .
bPress Menu, 2, 1, 2. 
21.Setup Receive
2.F/T Ring Time
a20 Secs
b30 Secs
Select ab & OK
cPress a or b to select how long the 
machine will ring to alert you that you 
have a voice call (20, 30, 40 or 70 
seconds). Press OK.
dPress Stop/Exit. 
						

							Chapter 6
42
Fax Detect6
Turning fax detect  On allows the machine to 
receive fax calls automatically if you lift any 
handset on the same line as the machine.
When you see  Receiving on the LCD or 
when you hear ‘chirps’ through the handset of 
an extension phone connected to another 
telephone wall socket, just replace the 
handset and your mach ine will receive the 
fax. 
If this feature is set to on, but your machine 
does not connect a fax call when you lift the 
handset of an external or extension phone, 
press  l51  on the external or extension 
phone. (See  Operation from extension 
telephones  on page 49.)
Note
If you use a modem, or send faxes from a 
computer, on the same line and your 
machine intercepts them, set fax detect to 
Off.
 
aMake sure you are in Fax mode  .
bPress  Menu, 2, 1,  3. 
21.Setup Receive
3.Fax Detect
aOn
bOff
Select 
ab & OK
cPress  a or  b to select  On,or  Off .
Press  OK.
dPress  Stop/Exit .
Setting the Print Density6
You can adjust print density to make your 
printed pages darker or lighter.
aMake sure you are in Fax mode  .
b Press Menu, 2 , 1, 7. 
21.Setup Receive
7.Print Density
-
nnonn+ 
Select 
d  c  & OK
cPress  c to make the print darker.
Or press  d to make the print lighter. 
Press  OK.
dPress  Stop/Exit . 
						

							Receiving a fax
43
6
Additional receiving 
operations
6
Printing a reduced incoming 
fax6
If you choose On, the machine automatically 
reduces each page of an incoming fax to fit on 
one page of A4, Letter, Legal or Folio size 
paper.
The machine calculates the reduction ratio by 
using the page size of the fax and your Paper 
Size setting (Menu, 1, 3).
aMake sure you are in Fax mode  .
bPress Menu, 2, 1, 5.  
21.Setup Receive
5.Auto Reduction
aOn
bOff
Select ab & OK
cPress a or b to select On or Off. Press 
OK.
dPress Stop/Exit.
Duplex printing for Fax mode 
(MFC-8860DN and 
MFC-8870DW only)6
If you set Duplex to On for fax receive the 
machine will print received faxes on both 
sides of the paper.
You can use A4, Letter, Legal or Folio size of 
paper for this function. 
aMake sure you are in Fax mode  .
bPress Menu, 2, 1, 0. 
21.Setup Receive
0.Duplex
aOn
bOff
Select 
ab & OK
cPress a or b to choose On or Off. 
Press OK.
dPress Stop/Exit.
Note
When you turn Duplex on the auto 
reduction feature is also turned on.
  
						

							Chapter 6
44
Setting the Fax Receive 
Stamp6
You can set the machine to print the received 
date and time in the top centre of each 
received fax page.
aMake sure you are in Fax mode  .
bPress Menu, 2, 1, 9. 
21.Setup Receive
  9.Fax Rx Stamp
aOnbOff
Select 
ab & OK
cPress a or b to choose On or Off. 
Press OK.
dPress Stop/Exit.
Note
• The received time and date will not appear 
when using Internet Fax* (*MFC-8860DN 
and MFC-8870DW only).
• Make sure you have set the current date 
and time in the machine.
 
Receiving faxes into memory6
As soon as the paper tray becomes empty 
during fax reception, the screen will display 
No Paper, asking you to put paper in the 
paper tray. (See Loading paper, and other 
media on page 14.) If you are unable to put 
paper in the paper tray the following will 
happen:
If Memory Receive is On:6
The machine will carry on receiving the fax, 
with the remaining pages being stored in 
memory, if enough memory is available. 
Further incoming faxes will also be stored into 
memory until the memory is full. When the 
memory is full the machine will stop 
automatically answering calls. To print the 
faxes, put fresh paper in the tray.
If Memory Receive is Off:6
The machine will carry on receiving the fax, 
with the remaining pages being stored in 
memory, if enough memory is available. The 
machine will then stop automatically 
answering calls until fresh paper is put in the 
paper tray. To print the last fax you received, 
put fresh paper in the tray.
aMake sure you are in Fax mode  .
bPress Menu, 2, 1, 6.
cUse a or b to select On or Off. Press 
OK.
dPress Stop/Exit. 
						

							Receiving a fax
45
6 Printing a fax from the 
memory6
If you are using the Fax Storage feature 
(Menu, 2, 5, 1), you can still print a fax from 
the memory when you are at your machine. 
See Fax storage on page 61.
aPress Menu, 2, 5, 3. 
25.Remote Fax Opt
  3.Print Document
Press Start
bPress Start. 
						

							46
7
Phone line services7
Setting the Phone Line Type7
If you are connecting the machine to a line 
that features a PBX or ISDN to send and 
receive faxes, it is also necessary to change 
the Phone Line Type accordingly by 
completing the following steps.
aPress Menu, 0, 6. 
06.Phone Line Set
aNormal
ISDN
bPBX
Select 
ab & OK
bPress a or b to select PBX, ISDN (or 
Normal). Press OK.
cPress Stop/Exit.
PBX and TRANSFER7
The machine is initially set to Normal, which 
lets the machine connect to a standard PSTN 
(Public Switched Telephone Network) line. 
However, many offices use a central 
telephone system or Private Branch 
Exchange (PBX). Your machine can be 
connected to most types of PBX. The 
machine’s recall feature supports timed break 
recall only (TBR). TBR will work with most 
PBX systems allowing you to gain access to 
an outside line, or transfer calls to another 
extension. The feature works when Tel/R is 
pressed.
Note
You can program a Tel/R key press as 
part of a number stored in a One-Touch or 
Speed-Dial location. When programming 
the One-Touch or Speed-Dial number 
(Menu, 2, 3, 1 or 2, 3, 2) press Tel/R first 
(the screen displays “!”) then enter the 
telephone number. If you do this, you do 
not need to press Tel/R each time before 
you dial using a One-Touch or Speed-Dial 
location. (Storing One-Touch dial 
numbers on page 54 or Storing Speed-
Dial numbers on page 56.) However, if 
PBX is not selected in the Phone Line 
Type setting, you cannot use the One-
Touch or Speed-Dial number that Tel/R 
press is programmed into.
 
Phone and external devices7 
						

							Phone and external devices
47
7
BT Call Sign (U.K. only)7
The BT Call Sign subscriber service is a way 
to have a separate number for your machine, 
it allows you to have at least two separate 
telephone numbers on one phone line. Each 
phone number has its own distinctive ringing 
pattern.
You can set up your machine so that it only 
responds to the second number.
When you set the BT Call Sign feature to ON, 
the receive mode is set to Manual 
automatically. Manual mode will not respond 
to incoming telephone calls, since the 
number you use for telephone calls will use 
the normal ring pattern. If you turn the feature 
off, your receive mode will remain on 
Manual.
To enable the machine to work with BT 
Call Sign 
7
This feature will only work with your external 
phone.
aPress Menu, 2, 0, 2.
The screen displays the current setting.
 
20.Miscellaneous
2.BT Call Sign
aOn
bOff
Select ab & OK
bPress a or b to select On (or Off). 
Press OK.
cPress Stop/Exit.
Connecting an external 
TAD 
7
You can connect an external Telephone 
Answering Device (TAD) to the same line as 
your machine. When the TAD answers a call, 
your machine will “listen” for the CNG (fax 
calling) tones sent by a sending fax machine. 
If it hears them it will take over the call and 
receive the fax. If it does not hear them, it will 
let your TAD take a voice message and the 
display will show Telephone.
The external TAD must answer within four 
rings (we recommend you set it to two rings). 
This is because your machine cannot hear 
the CNG tones until the external TAD has 
picked up the call. The sending machine will 
send CNG tones for only eight to ten seconds 
longer. We do not recommend using the toll 
saver feature on your external TAD if it needs 
more than four rings to activate it.
Note
If you have problems receiving faxes, 
reduce the ring delay setting on your 
external TAD.
  
						

							Chapter 7
48
Connections7
The external TAD must be connected as 
shown in the illustration below.
 
1TAD
aSet your external TAD to one or two 
rings. (The machine’s Ring Delay 
setting does not apply.)
bRecord the outgoing message on your 
external TAD.
cSet the TAD to answer calls.
dSet the Receive Mode to 
External TAD. (See Choosing the 
receive mode on page 39.)
Recording an outgoing 
message7
aRecord 5 seconds of silence at the 
beginning of your message. This allows 
your machine time to listen for fax tones.
bLimit your speaking to 20 seconds.
cEnd your 20-second message by giving 
your Fax Receive Code for people 
sending manual faxes. For example: 
“After the beep, leave a message or 
send a fax by pressing l51 and Start.”
Note
We recommend beginning your OGM with 
an initial 5 second silence because the 
machine cannot hear fax tones over a loud 
voice. You may try leaving out this pause, 
but if your machine has trouble receiving, 
then you should re-record the OGM to 
include it.
 
Multi-line connections (PBX)7
We suggest you ask the company who 
installed your PBX to connect your machine. 
If you have a multi line system we suggest 
you ask the installer to connect the unit to the 
last line on the system. This prevents the 
machine being activated each time the 
system receives telephone calls. If all 
incoming calls will be answered by a 
switchboard operator we recommend that 
you set the Receive Mode to Manual.
We cannot guarantee that your machine will 
operate properly under all circumstances 
when connected to a PBX. Any difficulties 
with sending or receiving faxes should be 
reported first to the company who handles 
your PBX.
1
1 
						

							Phone and external devices
49
7
External and extension 
phones
7
Operation from extension 
telephones7
If you answer a fax call on an extension 
telephone, or an external telephone that is 
correctly connected to the machine into the 
correct socket on the machine, you can make 
your machine take the call by using the Fax 
Receive Code. When you press the Fax 
Receive Code l51, the machine starts to 
receive the fax. (See Fax Detect on page 42.)
If you answer a call and no one is on 
the line:
7
You should assume that you’re receiving a 
manual fax.
aPress l51 and wait for the chirp or until 
the machine’s LCD shows Receiving, 
and then hang up.
Note
You can also use the Fax Detect feature to 
make your machine tactically take the call. 
(See Fax Detect on page 42.)
 
For Fax/Tel mode only7
When the machine is in Fax/Tel mode, it will 
use the F/T Ring Time (pseudo/double-
ringing) to alert you to pick up a voice call.
Lift the external telephone’s handset, and 
then press Tel/R to answer.
If you’re at an extension phone, you will need 
to lift the handset during the F/T Ring Time 
and then press #51 between the 
pseudo/double rings. If no one is on the line, 
or if someone wants to send you a fax, send 
the call back to the machine by pressing l51.
Connecting an external or 
extension phone7
You can connect a separate telephone 
directly to your machine as shown in the 
diagram below.
 
1 Extension telephone
2 External telephone
When you are using an external telephone, 
the LCD shows Telephone.
Using extension telephones (U.K. 
only)
7
Your premises may already be wired with 
parallel extension telephones (those 
connected to sockets in other rooms in the 
building), or perhaps you intend to add 
extension telephones to your line. While the 
simplest arrangement is a parallel 
connection, there are some reasons why this 
arrangement may cause problems.
The most common problem, is someone 
picking up an extension telephone while the 
machine is trying to send a fax.
Such problems can easily be eliminated, if 
you arrange modification of your extension 
wiring circuit, such that extension devices are 
connected “downstream” of your machine, in 
a master/slave configuration (see figure 2). In 
such a configuration, this machine can 
always detect whether a telephone is in use, 
so it will not attempt to seize the line during 
that time. This is known as “telephone off-
hook detection”.
1
2 
						

							Chapter 7
50
The inadvisable configuration is shown in 
figure 1, and the recommended master/slave 
configuration is shown in figure 2.
This new connection configuration can be 
arranged by contacting BT, Kingston upon 
Hull Telecommunications, your PBX 
maintainer or a qualified telephone 
installation company as appropriate. Simply 
explained, the extension telephone circuit 
should be terminated on a normal modular 
plug (BT 431A style), which in turn should be 
inserted into the modular socket of the white 
“T”-shaped connector provided as part of the 
line cord assembly.
Figure 1:
 7
1 Extension socket
2 Master socket
3 Incoming line
Figure 2:
Recommended connection of extension 
sockets
 7
1 Extension socket
2 Master socket
3 Incoming line
These phones are now connected as external 
devices as shown on page 49, because they 
are connected to the fax machine via the T-
connector.
Using a cordless external 
handset7
If your cordless telephone is connected to the 
telephone line cord (see page 49) and you 
typically carry the cordless handset 
elsewhere, it is easier to answer calls during 
the Ring Delay. 
If you let the machine answer first, you will 
have to go to the machine so you can press 
Tel/R to transfer the call to the cordless 
handset.
Using remote codes7
Fax Receive Code7
If you answer a fax call on an extension or 
external telephone, you can tell your machine 
to receive it by dialling the fax receive code 
l51. Wait for the chirping sounds then 
replace the handset. See Fax Detect on page 
42.
FAX
12
3 1
FAX
12
3 1