Candy Cdi 1010 S User Instructions

							Congratulations!
Thank you for choosing a Candy
appliance; quality dishwashers which
guarantee high performance and
reliability.
Candy manufacture a vast range
of domestic appliances: washing
machines, washer/dryers, cookers,
microwave ovens, ovens and hobs,
refrigerators and freezers.
Ask your dealer for the catalogue with
the complete range of Candy products.
Please read this booklet carefully  as
it provides important information
regarding the safe installation, use,
and maintenance of the machine,
together with some useful advice on
how to achieve the best results from
your dishwasher.
For future reference please keep this
instruction booklet in a safe place.
CUSTOMER SERVICE AND 
GUARANTEEYour new appliance is fully guaranteed
by the manufacturer for 12 months
against electrical/mechanical break-
down excluding:
A.Any faults which occur due to bad
installation or misuse of the machine.
B.Any faults which occur due to repair
of, or interference with, the machine
by any person not authorised by the
manufacturer to carry out service.
C.Any faults which occur due to
any parts which are fitted to the
machine which are not the original
manufacturers parts.
D.Any faults arising from non-domestic
use or unusual or abnormal use of
the machine.
E.Any faults arising from operation at
incorrect voltage.
F.Any faults arising from incorrect
operation of the machine.
The guarantee applies to Gt Britain
and Northern Ireland only, and is an
addition to your statutory rights.
AFTER SALES SERVICEFor service and repairs call your local engineer on our national telephone number: 
GIAS Service           Tel: 08705 400 600 
Support Service       (Eire 018301 666)
81
 
						

							83
SAFETY INSTRUCTIONSThere are certain basic safety rules
which are valid for any domestic
appliance. Installation■Make sure that the plug fitted to the
machine is compatible with the power
supply socket. If it is not, get a suitably
qualified person to fit the correct type,
and to make sure that the cables to the
mains socket are able to cope with the
power rating of the appliance.
■Ensure that the dishwasher does not
crush power cables.
■In general it is not advisable to use
adaptors, multiple plugs and/or extension
cables.
■Should it be necessary to replace the
supply cord, call the After Sales Service
Centre.Safety■Never touch the appliance when your
hands or feet are wet or damp.
■Do not use when your feet are bare.
■Do not remove the plug from the mains
supply socket by pulling the mains cable
or the machine itself.
■Do not leave the appliance exposed to
the elements (rain, sun etc).
■Do not let children (or others incapable
of operating it) use the machine without
supervision.
■Water left in the machine or on the
dishes at the end of the wash programme
should not be swallowed.
■The door should not be left in the open
position since this could present a potential
hazard ( es. tripping ).
■Leaning or sitting on the open door of
the dishwasher could cause it to tip over.WARNING !
Knives and other utensils with sharp
points must be loaded in the basket
with their points down or placed in a
horizontal position.
Daily use■This appliance is be designed for domestic
use only.
■The dishwasher is designed for normal
kitchen utensils.
Objects that have been contamined by
petrol, paint, traces of steel or iron,
corrosive chemicals, acids or alkalis
must not be washed in the dishwasher.
■If there is a water softening device installed
in the home there is no need to add
salt to the water softener fitted in the
dishwasher.
■Cutlery is washed best if it is placed in
the basket with the handles downwards.
■If the appliance breaks down or stops
working properly, switch it off, turn off the
water supply and do not tamper with it.
Repair work should only be carried out
by an approved service agent and only
genuine spare parts should be fitted. Any
failure to follow the above advice may
have serious consequences for the safety
of the appliance.Disposal■The dishwasher has been made from
materials which can be recycled so that it
can be disposed of in an environmentally
friendly way.
■If you wish to dispose of an old dishwasher
be careful to remove the door to
eliminate the risk of children becoming
trapped inside it.
82
CONTENTSSafety advice
Setting up, installation
Water softener unit
Loading the salt
Adjusting the upper basket
Loading the dishes
Information for test laboratories
Loading the detergent 
Types of detergent
Loading the rinse aid
Cleaning the filters
Some practical hints
Routine cleaning and maintenance
Description of the control panel
Technical data
Programme selection and special functions
Programme guide 
Identifying minor faultspag. 83  
pag. 84
pag. 87
pag. 88
pag. 89
pag. 90
pag. 92
pag. 93
pag. 94
pag. 95
pag. 96
pag. 97
pag. 98
pag. 99
pag. 99
pag. 100
pag. 102
pag. 104Please read the instructions in this booklet carefully because they contain important
information on how to install, use and maintain your dishwasher safely as well as
containing useful tips on how to make the most of it.
Keep this booklet safe for future reference.
Fig. A
321
4 5
 
						

							Water connectionIMPORTANT
The appliance must be connected to
the water mains using new hose-sets.
The old hose-sets should not be reused.
■The inlet and drain hoses can be directed
to left or right.
IMPORTANT
The dishwasher can be connected to
either cold or hot water, as long as it
is no hotter than 60 °C.
■Water pressure must be between
0,08 MPa and 0,8 MPa. If the pressure is
below the minimum consult our service
department for advice.
■The inlet hose must be connected to a
tap so that the water supply can be cut
off when the machine is not in use
(fig. 1 B).
■The dishwasher is fitted with 3/4" threaded
connector (fig. 2). 
■Connect inlet hose “A”to water tap “B”
with a 3/4" attachment making sure that
it has been properly tightened.
■If it is necessary, the inlet pipe can be
lengthened up to 2,5 m. The extension
pipe is available from the After Sales
Service Centre.
■If limescale deposits or sand are present
in the water, it is advisable to obtain the
appropriate filter, art. 9226085, from the
After Sales Service Centre (fig. 3). The
filter “D”must be inserted between the tap
“B”and the inlet hose “A”, remembering
to fit the washer “C”. 
■If the dishwasher is connected to new
pipes or to pipes which have not been in
use for a long time run water through for
a few minutes before connecting the
inlet hose. In this way no deposits of
sand or rust will clog up the water inflow
filter.
1
2
3
85
84
INSTALLATION(Technical notes)IMPORTANT
When the appliance is located on a
carpet floor, attention must be paid to
ensure that there is no obstruction to
the bottom vents.
Make sure that the plug on the
appliance remains accessible after
installation.Electrical connectionThis appliance complies with international
safety standards, and is fitted with a 3 pin
plug with earth connection to ensure
complete earthing of the product.
Before connecting the appliance to the
mains supply it is important to ensure:
1.that the supply socket is properly
earthed;
2.that your electricity supply is capable of
meeting the consumption requirements
listed on the rating plate of your
appliance.
WARNING!
Ensure that your product is properly
earthed. 
In the absence of adequate earthing
you will notice that when touching
the metal parts of your appliance an
electrical dispersion can be felt, due
to the presence of a radio interference
suppressor.
Manufacturer declines all responsibility
for any damage due to non-earthing of
the machine.
This appliance complies with
Directives 89/336/EEC, 73/23/EEC
and following changes.
Electrical connection (for U.K. only) Plug your dishwasher into the power
socket.
If the plug we supply does not fit :
■CUT IT OFF AND DESTROY IT!
You can't use it on other appliances, and
the exposed wires could be dangerous if
anyone plugged it in.
■Fit a suitable plug, as follows:
WARNING!
THIS APPLIANCE MUST BE EARTHED.
Fuses and plugs
This appliance should be used only on a
socket with a minimum rating of 13 Amp.
Our ready-fitted plug is already equipped
with a 13 amp fuse which is BS 1362 ASTA
approved.
Any replacement should be exactly the same.
If the fuse cover is lost, do not use the plug
until it is replaced. 
Acorrect replacement fuse cover (obtaina-
ble from your dealer or Electricity board)
must be the same colour as shown or
named on the insert on the base of the
plug.Green and
yellow wireMarked with the letter E,
OR marked with the Earth
symbol, 
OR coloured green,
OR coloured green and
yellow.
Blue wire 
Brown wireMarked N,
OR coloured black.
Marked L,
OR coloured red.Connect        to the terminal in the plug
 
						

							According to the degree of hardness of
your water, regulate the softener unit in the
following way:
IMPORTANT
The dishwasher must be ALWAYS off
before start this procedure.
1.Press the "ON/OFF"button.
2.Wait for the programme indicator lights
to start flashing.
3. WITHIN  2  MINUTESof  switching  the
machine  on,  hold  down  the
"PROGRAMME  SELECTION"button
(PR.) for at least 10seconds (an
intermittent acoustic signal will sound).
4.When the 3 indicator lights on the left
will come on and the acoustic signal will
stop, release the button.
5.The light indicating the water softener
setting level will come on and the alarm
will shortly sound once. To change the
setting, press the "PROGRAMME
SELECTION"button: each time the
button is pressed, one indicator light
will come on (for level 5 all the indicator
lights will come on).
6.When the required setting is reached,
wait for the alarm to sound to indicate
that the settings were saved (the
programme indicator lights will return to
flash).
WARNING!
If any problem occurs, turn the
dishwasher off by pressing the
"ON/OFF" button and start the
procedure again from the beginning
(STEP 1).
87
WATER SOFTENER UNITDepending on the source of the supply,
water contains varying amounts of limestone
and minerals which are deposited on the
dishes leaving whitish stains and marks.
The higher the level of these minerals
present in the water, the harder the water is.
The dishwasher is fitted with a water
softener unit which, through the use of
special regenerating salt, supplies
softened water for washing the dishes. 
The degree of hardness of your water can
be obtained from your water supply
company.Regulating the water softener 
with electronic programmerThe softener unit can treat water with a
hardness of up to 90°fH (French grading)
or 50°dH (German grading) through six
different settings.
The table below lists different degrees of
water hardness with the corresponding
setting for the softener unit.
*The water softener unit is set in the
factory at level 3, as this is suitable for
the majority of users.
Level
°fH
(French)
°dH
(German)
NOYES
YES
YES
YES
YES
Indicator
light 1
Indicator
light 1
Indicator
light 2
Indicator
light 3
Indicator
light 4
Indicatorlights 1,2,3,4
Water
hardness
Water
softener
setting
Use of
regenerating
salt
0
1
2
*3
4
5
0-5
6-15
16-30
31-45
46-60
61-900-3
4-9
10-16
17-25
26-33
34-50
1234“PROGRAMME SELECTION” button
“ON/OFF”
button
Indicator lights
86
Connecting the outlet hose■The outlet hose should disharge into a
standpipe, making sure that there are no
kinks (fig. 4).
■The standpipe must be at least 40 cm
above floor level and it must have an
internal diameter of at least 4 cm.
■It is advisable to fit an anti-odour air trap
(fig. 4X).
■If necessary the outlet hose can be
extended up to 2,5 m, provided that it is
kept at a maximum height of 85 cm
above floor level. The extension pipe is
available from the After Sales Service
Centre.■The hose can be hooked over the side of
the sink, but it must not be immersed in
water, in order to prevent water from
being syphoned back to the machine
when this is in operation (fig. 4Y).
■When installing the appliance under a
worktop the hose pipe clamp must be
attached to the wall in the highest possible
position under the worktop (fig. 4Z).
■Check that there are no kinks in the inlet
and outlet hoses.
4
Opening the doorIf the machine comes open while it is working,
an electrical safety device automatically
switches everything off. 
IMPORTANT
For the machine to work properly,
the door should not be opened while
it is in operation.
Closing the doorPlace the baskets in the machine. 
Make sure that both the spray arms are
free to rotate and are not obstructed by
cutlery, crockery or pans. Close the door,
pressing on it to make sure it is firmly shut.
 
						

							89
ADJUSTMENT OF THE
UPPER BASKETIf 27 cm to 31 cm plates are normally used,
load them onto the lower basket after the
upper basket has been placed in its upper
position and proceed as detailed below:
1.Turn the front stops “A” outwards;
2.Take out the basket and remount it in the
upper position;
3.Replace the blocks “A” in their original
position.
Dishes that are bigger than 20 cm in
diameter can no longer be loaded onto the
upper basket and the mobile supports
cannot be used when the basket is in the
upper position.
A
A
LOADING THE SALT■On the bottom of the machine there is a
container for the salt for regenerating
the softener.
■It is important to use only a salt that is
specifically designed for dishwasher.
Other types of salt contain small quantities
of insoluble particles which over a long
period of time may affect and deteriorate
the softener performance. 
■To add salt, unscrew the cap of the con-
tainer on the bottom and then refill the
container. 
■During this operation a little water will
overflow; but keep adding salt until the
container is full. When the container is
full, clean the thread of salt residue and
retighten the tap.
■After loading the salt, it is recommended
running a complete washing cycle,
or COLD RINSE programme. 
The salt dispenser has a capacity of
between 1.5 and 1.8 kg and, for efficient
88
Salt loading indicatorThis model is provided with a blind cap. In
this case, the salt level must be checked
periodically, according to the regulation of
the water softener unit.
IMPORTANT 
The appearance of white stains on
dishes is generally an important
sign that the salt container needs
filling.
use of the appliance, it should be refilled
from time to time according to the
regulation of the water softener unit.
IMPORTANT
(Only for first start up)
When the appliance is used for the
first time, after completely filling the
salt container, it is necessary to add
water until the container overflows.
 
						

							91
Astandard daily load is represented in figs. 1, 2and 3.
Upper basket (fig. 1)
A=soup plates
B=dinner plates
C=dessert plates
D=saucers
E=cups
F=glasses 
Upper basket (fig. 2)
A=soup plates
B=dinner plates
C=dessert plates
D=saucers
E=cups
F= glasses
G=single section cutlery basket
Lower basket (fig. 3)
A=medium-sized saucepan
B=large saucepan 
C=frying pan
D=lids
E=tureens, serving dishes
F=cutlery
G=oven dishes
Please load the dishwasher sensibly to ensure the
best wash results.
Cutlery basket (fig. 4) 
The cutlery basket is made with two detachable
parts which will enable various loading options. The
two parts can be detached by sliding the left section
away from the right section.
D
FAG
E
B
C
34
A
BC
D
G E
F
2
F
1
A
BC
D
EF
90
LOADING DISHESUsing the upper basket■The upper basket is provided with mobi-
le racks hooked to the sides of the
basket which can be regulated in two
positions: upright and lowered. In the
lowered position the racks may be used
for tea and coffee cups, kitchen knives
and ladles. Glasses with stems may be
safely hung on the ends of the racks.
Glasses, cups, saucers and dessert
plates may be loaded under the racks.
■Soup plates and ordinary plates may be
loaded with the rack in the upright
position. Plates should be loaded
vertically with   the underside of the plate
towards the back of the dishwasher with
a space between each plate to allow
water to pass freely.
■It is advisable to load plates of the same
size together in order to utilize maximum
basket capacity.
■Plates may be loaded in a single row
(fig. 1) or on both rows (fig. 2).
■It is advisable to load large plates
(approx. 27 or more cm) slightly tilted
towards the rear to facilitate introduction
of the basket into the machine.■Salad bowls and plastic bowls may also
be loaded on the upper basket. It is
advisable to block these in place so that
the jets of water do not make them
overturn.
■The upper basket has been designed to
offer maximum flexibility in use and can
be loaded with up to 24 plates on two
rows, up to 30 glasses on five rows or a
mixed load.
Using the lower basket■Saucepans, oven dishes, tureens, salad
bowls, lids, serving dishes, dinner
plates, soup plates and ladles can be
loaded on the lower basket.
■Place the cutlery in the plastic cutlery
holder with the handles pointing
upwards.
■Place the cutlery holder on the lower
basket (fig. 3), making sure that the
cutlery does not get in the way of the
rotating arms.
IMPORTANT
The lower basket has a  safety-stop
device,for its safe extraction, also
especially useful with a full load.
For loading salt, cleaning filter and for
ordinary maintenance, the complete
extraction of the basket is necessary. 
 
						

							LOADING THE DETERGENT The detergentIMPORTANT
It is essential to use a detergent
that is specifically designed for
dishwashers either in powder, liquid
or tablet form.
“FINISH” gives very good results and can
be easily obtained.
Unsuitable detergents (like those for
washing up by hand) do not contain the
proper ingredients for use in a dishwasher,
and stop the dishwasher from working
correctly.Filling the detergent containerThe detergent container is inside the door
(fig. A “2”). If the lid of the container is
closed, press the button(A)to open. 
At the end of every wash cycle the lid is
always open and ready for the next time
the dishwasher is used.
WARNING!
When loading the lower basket, please
ensure that the plates or others do not
obstruct the detergent dispenser.
The amount of detergent to be used varies
according to how dirty the dishes are and
on the type of dishes to be washed.
We advise using 20÷30 g of detergent in the
wash section of detergent compartment (B).
93
After pouring the detergent into the container,
close the lid, firstly pushing (1)and then
pressing on it (2) until you hear the click.
Since not all detergents are the same the
instructions on the boxes of detergent can
vary. We should just like to remind users
that too little detergent does not clean the
dishes properly whilst too much detergent
will not produce better results and is also a
waste. 
IMPORTANT
Do not use an excessive amount of
detergent and help limit damage to
the environment at the same time.
A
B
Lower basket (fig. 6)
M= 8 + 4 soup plates
N= 11 + 1 dinner plates
O= 12 dessert plates
P=serving dish
Q=cutlery
92
Upper basket (fig. 5) 
A= 5 + 5 + 2 glasses
B= 12 saucers
C= 4 + 6 + 2 cups
D= small bowl
E= medium bowl
F= large bowl
G= 1 fork
H= 1 + 1 serving spoonsI= 3 + 3 dessert spoonsL= 3 + 3 teaspoons
INFORMATION FOR THE TEST LABORATORIESGeneral programme comparison  (Ref. EN 50242 Standards) (see programmes selection)
1.Upper basket position: low
2.Normal load
3.Shine setting: 612 international place load (Ref. EN 50242)Correct loading is indicated, in fig. 5for the upper basket, in fig. 6for the lower
basket and in fig. 7for the cutlery basket.
Cutlery basket without side racks (fig. 7)
Insert the remaining cutlery, taking care not to
load more than two differenttypes of cutlery in
the same compartment.
4.Amount of detergent:
- 8 g for pre-wash;
- 22 g for wash.
A F
C
C C G
B
E D
H
H
5
L I
QN
M
P
O
MN
6
A
A
7
 
						

							LOADING THE RINSE AIDThe rinse aidThe rinse aid, which is automatically
released during the last rinsing cycle, helps
the dishes to dry quickly and prevents
spots and stains forming.Filling the rinse aid containerThe rinse aid container can be found to the
left of the detergent container (fig. A "3").
To open the lid, push the reference mark
and, in the same time, pull the tab of
opening.
It is always advisable to use rinse aid that
is specifically designed for dishwasher.
Check the rinse aid level through the
indicator eye (C)which is located on the
dispenser.Regulating the rinse aid from 1 to 6The regulator (D)is placed under the lid
and can be turned using a coin. 
The recommendedposition is 4.
The limestone content of the water
considerably affects the formation of
limescale and the drying performance.
It is therefore important to regulate the
quantity of rinse aid to achieve good
washing results.
If, after the wash, streaks occur on the
dishes, decrease the amount by one
position. If whitish spots occur, increase the
amount by one position.
95 FULL EMPTY
dark                     light
C
D
TYPES OF DETERGENTDetergent tabletsDetergent tablets of different manufacturers
dissolve at different speeds, for this
reason, during short programmes, some
detergent tablets may be not fully effective,
because they are not completely dissolved.
If these products are used, is recommended
to choose longer programmes to guarantee
the complete use of the detergent. 
IMPORTANT
To get satisfactory washing results,
the tablets MUST be placed in the
wash section of the detergent
container and NOT directly in the
tub.Concentrated detergentsThe concentrated detergents, with reduced
alkalinity and with natural enzymes, in
conjunction with 50°C wash programmes,
have a smaller impact on the environment
and they protect the dishes and the
dishwasher. 
The 50°C wash programmes purposely
exploit the dirt-dissolving properties of the
enzymes, allowing therefore, with the use
of the concentrated detergents, to achieve
the same results of the 65°C programmes
but at a lower temperature.   Combined detergentsThe detergents that also contain the rinse
aid must be placed in the wash section of
the detergent container. The rinse aid
container must be empty (if it is not empty,
set the rinse aid regulator to lowest position
before using combined detergents)."3 in 1"/"4 in 1"/"5 in 1" 
combined detergentsIf you are planning to use combined detergents
i.e. those with built in salt and/or rinse
agent, we would advise the following:
■read carefully and follow the manufacturer’s
instructions given on the packaging;■the effectiveness of detergents containing
the built in water softener/salt depends
on the hardness of your water supply.
Check that the hardness of your water
supply is within the effective range given
on the detergent packaging. 
If when using this type of product, you
dont get satisfactory washing results,
please contact the detergent
manufacturer.
In certain circumstances use of combined
detergents can cause:
■limescale deposits on dishes or in the
dishwasher;
■a reduction in washing and drying
performance.
IMPORTANTAny problems which arise as a direct
result of the use of these products
are not covered by our warranty.
Please note that using the 3 in 1/
4 in 1/”5 in 1 combined detergents,
the rinse aid and salt indicator lights
(only used on selected models) are
superfluous, so you must ignore the lights.
If washing and/or drying problems occur,
we recommend you return to use traditional
separate products (salt, detergent and
rinse agent). This will ensure that the water
softener in the dishwasher operates
correctly.
In this case, we recommends that you:
■refill both the salt and rinse aid container;
■run one normal washing cycle without a
load.
Please note that on return to the use of
conventional salt, a number of cycles will
be required before the system becomes
fully efficient again.
94
 
						

							97
PRATICAL HINTSHow to get really good wash
results■Before placing the dishes in the
dishwasher, remove any remaining
food (bones, shells, pieces of meat or
vegetables, coffee grounds, skin of fruit,
cigarette ash, tooth picks etc. to avoid
blocking the filters, water outlet and
washing arm nozzles.
■Try not to rinse the dishes before
loading them into the dishwasher.
■If saucepans and oven dishes are
encrusted with the remains of burnt or
roast food, it is advisable to leave them
to soak before washing.
■Place the dishes face downwards.
■Try to place the dishes in such a way
that they are not touching one another.
If they are loaded properly you will get
better results.
■After loading the dishes check that the
washing arms can rotate freely.
■Pans and other dishes that have
particularly stubborn food particles or
remnants of burnt food should be left to
soak in water with dishwasher
detergent.
■To wash silver properly:
a)rinse the silver immediately after
use, especially if it has been used for
mayonnaise,eggs, fish etc.;
b) do not sprinkle detergent onto it;
c)keep it separate from other metals.
How to make savings■If you want the dishwasher to give a
complete wash, place the dishes in the
dishwasher at the end of each meal and
if necessary turn on the COLD RINSE
cycle to soften the food remains and
remove bigger particles of food from the
new load of dishes. 
When the dishwasher is full start the
complete wash cycle programme.
■If the dishes are not very dirty or if the
baskets are not very full select an
ECONOMY programme, following the
instructions in the program list.What not to wash■It should be remembered that not all
dishes are suitable for washing in a
dishwasher.We advise against using
the dishwasher to wash items in
thermoplastic, cutlery with wooden or
plastic handles, saucepans with
wooden handles, items in aluminium,
crystal, leaded glass unless otherwise
stated. 
■Certain decorations may fade. It is
therefore a good idea before loading the
whole batch to wash just one of the
items first so as to be sure that others
like it will not fade.
■It is a good idea not to put silver cutlery
with non-stainless steel handles into
the dishwasher as there could be a
chemical reaction between them.
IMPORTANT
When buying new crockery or
cutlery always make sure that they are
suitable for washing in a  dishwasher.Useful hints■In order to avoid any dripping from the
top rack, remove the lower rack first.
■If the dishes are to be left in the
machine for some time, leave the door
ajar, to let some air circulate and to
improve the drying performance. 
96
123
CLEANING THE FILTERSThe filter system(fig.A “4”) consists of: 
a central containerthat traps the larger
particles;
a flat gauzethat continuously filters the
wash water;
a micro filter, located beneath the gauze,
that traps the tiniest particles ensuring a
perfect rinse.
■To achieve excellent results every time,
the filters should be checked and
cleaned after each wash. 
■To remove the filter unit, simply turn the
handle anticlockwise (fig. 1).
■For ease of cleaning, the central container
is removable (fig. 2).
■Remove the gauze filter (fig.3)and
wash the whole unit under a jet of
water. If necessary a small brush can
be used.
■With the Self-cleaning Micro filter,
maintenance is reduced and the filter
unit need only be checked every two
weeks. Nevertheless, after each wash it
is advisable to check that the central
container and the gauze filter are not
clogged.
WARNING!
After cleaning the filters, make sure
that they are correctly reassembled
and that the gauze filter is properly
positioned at the bottom of the
dishwasher.
Make sure that the filter is screwed
back, clockwise, into the gauze, as
poor seating of the filter unit could
have an adverse effect on the
efficiency of the appliance.
IMPORTANT
Never use the dishwasher without
the filters.
 
						

							99
EN 50242 place load
Capacity with pans and dishes
Water supply pressure 
Fuse
Power input
Supply voltage12
8 persons
Min. 0,08 - Max 0,8 MPa
(see rating plate)
(see rating plate)
(see rating plate)DESCRIPTION OF THE CONTROL PANEL
TECHNICAL DATA: DIMENSIONS:Height
Depth 
Width 
Depth with door open
cm
cm
cm
cm82 ÷ 88,5
55
59,8
11 7
A
"ON/OFF" button 
B
PROGRAMME DESCRIPTION
C 
"PROGRAMME SELECTION" button
D 
"PROGRAMME SELECTION" 
indicator lights
C
BA
D
98
WHEN CYCLE IS FINISHEDAfter every wash it is essential to turn off
water supply and to switch off the machine
by pressing the On/Off button to the off
position. 
If the machine is not going to be used for
some time, it is advisable to follow these
rules:
1.doan empty wash with detergent in order
to clean the machine of any deposits;
2.pull out the electric plug;
3.turn off the water tap;
4.fill the rinse aid container; 
5.Ieave the door ajar;
6.keep the inside of the machine clean;
7.If the machine is left in places where the
temperature is below 0°C any water left
inside the pipes may freeze. Wait until
the temperature rises above zero and
then wait for about 24 hours before
starting up the dishwasher.
CLEANING AND 
MAINTENANCE■To clean the dishwasher outside, do not
use solvents (degreasing action) neither
abrasives, but only a cloth soaked with
water.
■The dishwasher does not require special
maintenance, because the tank is
self-cleaning. 
■Regularly wipe the door gasket with a
damp cloth to remove any food remains
or rinse aid. 
■It is advisable to remove limestone
deposits or dirt periodically, by doing an
empty wash; pour a glass of vinegar on
the bottom of the tank and select the
light wash.
■If, in spite of the routine cleaning of the
filters, you notice that the dishes or pans
are not properly washed or rinsed, check
that all the spray heads on the rotor
arms (fig. A “5”)are clear.
If they are blocked, clean them in the
following way:
1.to remove the upper rotor arm, turn it
until it lines up with the stop marked
by the arrow (fig. 1). Push it upwards
(fig. 1b)and, keeping it pushed in,
unscrew it in a clockwise direction
(to reassemble it repeat the same
operation, but turn it anticlockwise).
The lower rotor arm can be removed
simply by pulling it upwards (fig. 2);
2.wash the rotor arms under a jet of water
to clear any blockage in the spray
heads;
3.when you have finished, refit the rotor
arms in the same position, remembering
to re-align the arrow and screw into
position.
■Both the door lining and the tank lining
are in stainless steel; however, should
spots caused by oxidation occur, this is
probably due to a high level of iron salts
presents in the water. 
■The spots can be removed with a mild
abrasive agent; never use chlorine
based materials, steel wool, etc.  
12
1b