Canon network camera VBM600VE User Manual

[Network] Setting Administrator Password, LAN, IP Address, DNS, etc
5-7
5
Setting Page
SNMP
(1) [SNMP] 
Set SNMP use to [Disable] or [Enable]. Camera 
information can be referenced by the SNMP Manager 
if [Enable] is specified. 
(2) [Community Name] 
Set a community name for SNMP. It is recommended 
that you change the community name to ensure 
system security. 
(3) [Administrator Contact Information] 
Set contact information (e-mail address, etc.) for the 
Administrator of the camera. Setting...

5-8
Current Date and Time
[Date], [Time] 
The date and time currently set in the camera are 
shown. 
Setting
(1) [Setting Method] 
Select from [Set manually], [Synchronize with NTP 
server], [Synchronize with NTP broadcast ], 
[Synchronize with computer time].
(2) [Date], [Time] 
Set the following according to the selection made in 
[Setting Method]. 
[Set manually] 
Set the desired date and time. The date is set by , and the time in 2 4 -h ou r f o rm at  i n  t he  
order  (two digits for month, 
day...

5-9
5
Setting Page
Camera Name
[Camera Name] 
Be sure to enter [Camera Name (alphanumeric 
characters)].
Up to 15 ASCII characters (spaces and printable 
characters) may be used for [Camera Name 
(alphanumeric characters)]. 
Note
 The camera name set here will be shown when the camera is 
registered for use with included RM-Lite. 
Initial Camera Settings
(1) [AE Mode], [Slow Shutter], [Shutter Speed] 
Set the exposure control and shutter speed for the 
camera startup. [AE Mode] 
[Auto] 
The exposure is...

5-10
Use this mode to stabilize the exposure in locations 
where vehicles or people are moving. 
[Spot] 
The center of the screen is metered. 
An appropriate exposure can be achieved for the 
subject at the center of the screen regardless of the 
brightness/darkness on the periphery of the screen. 
Use this mode if you want to adjust the exposure to 
the center of the screen because the subject is 
receiving a spotlight or backlight, etc. 
(4) [Focus Mode] 
Set the focus mode when camera starts. 
[Auto]...

[Camera] Setting Initial Camera Settings and External Device Name
5-11
5
Setting Page
Day/Night
(1) [Mode] 
Set Day/Night mode to [Manual] or [Auto]. 
If [Manual] is selected, it is possible to switch 
manually between [Day Mode] and [Night Mode] 
using Admin Viewer Night Mode function (p. 7-17). 
If you have selected [Auto], set [Switching Brightness] 
and [ Response (sec.)] according to the environment 
in which the camera is installed as well as the desired 
switching conditions. 
(2) [Switching...

5-12
(1) [Restricted to Presets] 
Set the camera control preset to [No Restriction] or 
[Preset Only]. The administrator can limit camera 
control by non-administrators to preset angles by 
selecting [Preset Only]. 
(2) [Camera Position without Control] 
Select either [Do not return to Home Position] or 
[Return to Home Position] as the action when no 
control privileges are requested by users and the 
home position has already been set. 
When [Return to Home Position] is selected and no 
users have...

5-13
5
Setting Page
Initial Camera Settings
(1) [Intelligent Function Information] 
Select from [Do not add] or [Add] for intelligent 
function information other than volume detection in 
JPEG header information. 
JPEG
(1) [Image Quality] 
Select a desired image quality from 1 to 5 (5 levels) for 
images transmitted at each image size in JPEG. 
Greater values have higher quality. 
(2) [Image Size: Image Transmission] 
Select [160 x 120], [320 x 240], [640 x 480] or 
[1280 x 960] for the size of images...

5-14
On-screen display
(1) [Date display] 
Select whether to enable date display over images. If 
[Enable] is selected, date information will be 
displayed over images. 
(2) [Position of date display] 
Select [Upper left], [Upper right], [Lower left] or 
[Lower right] for the position of date display 
information. 
(3) [Format of date display] 
Select [YYYY/MM/DD], [DD/MM/YYYY] or [MM/DD/
YYYY] for the format of the date display. 
(4) [Time display] 
Select whether to enable time display over images. If...

5-15
5
Setting Page
General Upload
[Upload] 
Select [Upload Disabled], [HTTP Upload] or [FTP 
Upload] for the upload method. 
Note
The server or network load may increase and the frame rate may 
drop, depending on the settings. If this occurs, try the following 
measures. Also check the settings including the network to the 
server. 
 Reduce the image file size:
– Set a lower value under [Image Quality] for JPEG (p. 5-13). 
– Set a lower value for [Image Size: Upload] for JPEG 
(p. 5-13). 
 Reduce the...

5-16
(7) [Parameter (query string)] 
Enter the parameter (using up to 127 characters). 
Parameters can be specified using the “%” character 
(p. 8-4).
(8) [HTTP Upload Test] 
Clicking [Exec] initiates an upload test based on the 
settings currently entered. Only one JPEG image is 
uploaded. It is not necessary to click [Apply].
After entering a password, first click [Exec], then 
[Apply] the password.
FTP Upload
(1) [Notification] 
The content of notification is set to [Image data upload 
with FTP]. 
(2)...