Canon printer imageCLASS MF247dw User Manual

							2Spreadthedocumentguidesapart.
	Slide the document guides outward until they are slightly farther apart than the actual document width.
3Fanthedocumentstackandaligntheedges.
	Fan the document stack in small batches, and align the edges by lightly tapping the stack on a  5at surface a
few times.
4Placethedocument(s)faceupinthefeeder.
	 Make sure that the document stack does not exceed the load limit guide ().
	 Do not load documents of various sizes at the same time.
	 Up  to  50  sheets *
  can  be  loaded  at  a  time.  If  50  or  more  sheets  are  loaded,  scanning  may  stop  or  a  paper
jam may occur.
* For MF247dw / MF236n, up to 35 sheets.
5Alignthedocumentguidesagainsttheedgesofthedocument.
	 Slide the document guides inward until they are aligned securely against the edges of the document.
Basic Operations
43 
						

								The machine is ready to scan the document.
Alignthedocumentguidessecurelyagainsttheedgesofthedocument
Document guides that are too loose or too tight can cause misfeeds or paper jam.
Whiledocumentsarebeingscanned
Do not add or remove documents.
Whenscanningiscomplete
Remove the scanned documents from beneath the feeder to prevent paper jams.
Basic Operations
44 
						

							LoadingPaper
1469-00S
You can load the paper into the paper drawer or manual feed slot. Load the paper you usually use into the paper drawer. The paper drawer is convenient when using large amounts of paper. Use the manual feed slot when you
temporarily use size or type of paper that is not loaded in the paper drawer. See 
Paper(P.650) for available paper
sizes.
PaperTypeandSettingfortheMachine
See the table below to specify the paper settings according to the type and weight of the paper to load into the
paper source. For more information about how to specify the paper settings on the machine, see 
Specifying
PaperSizeandType(P.56) . For the amount of paper that can be loaded in each paper source, see 
Paper(P.650).
Paper TypePaper WeightPaper Setting
on the Machine
Plain paper16 to 23 lb Bond (60 to 89 g/mt)
 *Recycled paper16 to 23 lb Bond (60 to 89 g/mt)Color paper16 to 23 lb Bond (60 to 89 g/mt)
Heavy paper
24 to 32 lb Bond (90 to 120 g/mt)33 to 60 lb Cover (121 to 163 g/mt)
Bond paper
16 to 24 lb Bond (60 to 90 g/mt)25 to 32 lb Bond (91 to 120 g/mt)33 to 60 lb Cover (121 to 163 g/mt)EnvelopeLabelIndex card*
 If set to  and that printout is curled, specify  and print again.Donotusethefollowingtypesofpaper:
	 Wrinkled or creased paper
	 Curled or rolled paper
	 Torn paper
	 Damp paper
Basic Operations
45          
						

								Very thin paper
	 Paper printed by a thermal transfer printer
	 Highly textured paper
	 Glossy paper
Paperhandlingandstorage 	 Store the paper on a  5at surface.
	 Keep the paper wrapped in its original package to protect the paper from moisture or dryness.
	 Do not store the paper in such a way that may cause it to curl or fold.
	 Do not store the paper vertically or stack too much paper.
	 Do not store the paper in direct sunlight, or in a place subject to high humidity, dryness, or drastic
changes in temperature or humidity.Whenprintingonpaperthathasabsorbedmoisture Steam may emit from the paper output area, or water droplets may form on the back side of theoperation panel or around the paper output area. There is nothing unusual about any of these
occurrences, which occur when the heat generated from  4xing toner on the paper causes moisture in the
paper to evaporate (most likely to occur at low room temperatures).
LINKS
RegisteringaCustomPaperSize(P.58)
Basic Operations
46    
						

							LoadingPaperinthePaperDrawer
1469-00U
Load the paper that you usually use in the paper drawer. When you want to print on paper that is not loaded in the paper drawer, load the paper in the manual feed slot.  
LoadingPaperintheManualFeedSlot(P.50)
Makesuretoloadpaperinportraitorientation
Paper cannot be loaded in landscape orientation. Make sure to load the paper in portrait orientation. 
1Liftthedustcover.2Slidethepaperguidesapart.
Sizeabbreviationsonthepaperguides
The abbreviations on the paper guides in the paper drawer indicate paper sizes as follows:
	 LGL: Legal
	 LTR: Letter
	 STMT: Statement
Basic Operations
47    
						

								EXEC: Executive
3Insertthepaperintothepaperdraweruntilthepaperstops.
	Load the paper in portrait orientation (with the short edge toward the machine), with the print side face up.
Paper cannot be loaded in landscape orientation.
	 Fan the paper stack well, and tap it on a  5at surface to align the edges.
	 When you insert the paper with  set to , a  con4rmation screen is
displayed. 
NotifytoCheckPaperSettings(P.487)
Donotexceedtheloadlimitguidewhenloadingpaper
Make sure that the paper stack does not exceed the load limit guide (
). Loading too much paper can cause
paper jams.
When loading envelopes or paper with a logo, see LoadingEnvelopes(P.52) or LoadingPreprinted
Paper(P.54) .
4Alignthepaperguidesagainsttheedgesofthepaper.
	Move the paper guides in so they are exactly the width of the paper.
Alignthepaperguidessecurelyagainsttheedgesofthepaper
Paper guides that are too loose or too tight can cause misfeeds or paper jams.
Basic Operations
48          
						

							5Lowerthedustcover.
WhenLegalsizepaperisloaded
The paper guides at the rear edge of the paper will be extended. Open the dust cover extension, then lower the dust cover.
6Pulloutthepaperstoppertoopen.}ContinuetoSpecifyingPaperSizeandType(P.56)
Whenchangingthepapersizeortype
The factory default settings for paper size and type are  and , respectively. If you load a different size or type of paper into the machine, make sure to change the settings.
If you do not change the settings, the machine cannot print properly.
PrintingontheBackSideofPrintedPaper(Manual2-SidedPrinting)You can print on the back side of printed paper. Flatten any curls on the printed paper and insert it into the
manual feed slot ( 
LoadingPaperintheManualFeedSlot(P.50) ), with the side to print face up (previously
printed side face down).
	 Load one sheet at a time per each print.
	 You can use only the paper printed with this machine.
	 You cannot print on the side that has previously been printed on.
	 If you are using A5 paper, the reverse side may not be printed correctly.
LINKS
Paper(P.650)
Basic Operations
49          
						

							LoadingPaperintheManualFeedSlot
1469-00W
When you want to print on paper that is not loaded in the paper drawer, load the paper in the manual feed slot. Load
the paper that you usually use in the paper drawer. 
LoadingPaperinthePaperDrawer(P.47)
Makesuretoloadpaperinportraitorientation
Paper cannot be loaded in landscape orientation. Make sure to load the paper in portrait orientation.
1Openthemanualfeedcover.2Spreadthepaperguidesapart.
	 Slide the paper guides outward.
3Insertthepaperintothemanualfeedslotuntilthepaperstops.
	Load the paper in portrait orientation (with the short edge toward the machine), with the print side face up.
Paper cannot be loaded in landscape orientation.
	 When you insert the paper with  set to , a  con4rmation screen is
displayed. 
NotifytoCheckPaperSettings(P.487)
Basic Operations
50       
						

							When loading envelopes or paper with a logo, see LoadingEnvelopes(P.52)or LoadingPreprinted
Paper(P.54) .
4Alignthepaperguidesagainsttheedgesofthepaper.
	Slide the paper guides inward until they are aligned securely against the edges of the paper.
Alignthepaperguidessecurelyagainsttheedgesofthepaper
Paper guides that are too loose or too tight can cause misfeeds or paper jams.
5Pulloutthepaperstoppertoopen.ContinuetoSpecifyingPaperSizeandType(P.56)Basic Operations
51          
						

							LoadingEnvelopes
1469-00X
Make sure to  5atten any curls on envelopes before loading them. Also pay attention to the orientation of envelopes
and which side is face up.
BeforeLoadingEnvelopes(P.52)
LoadedOrientation(P.53)
This section describes how to load envelopes in the orientation you want, as well as procedures that you need to complete before loading envelopes. For a description of the general procedure for loading envelopes in the paper drawer or manual feed slot, see 
LoadingPaperinthePaperDrawer(P.47)  or LoadingPaperin
theManualFeedSlot(P.50) .
Before Loading Envelopes
Follow the procedure below to prepare the envelopes before loading.
Only one envelope at a time can be loaded in the manual feed slot. Follow steps 1 to 4 in the procedure below to prepare the envelope for loading.
1Closethe 5apofeachenvelope.2Flattenthemtoreleaseanyremainingair,andmakesurethattheedgesarepressed
tightly.3Loosenanystiffcornersoftheenvelopesand 5attenanycurls.Basic Operations
52