Canon printer PIXMA MG2922 User Manual

							•If No Driver  is displayed for the name, associate the port with the printer.
When the Printer Driver Is Not Associated with a Port
•
If Not Found  is displayed for the status, check the followings:
•
The access point is turned on.
•
When using wired LAN, the LAN cable is connected properly.
•
If the printer on a network is not detected, make sure that the printer is turned on, then select
Refresh . It may take several minutes to detect printers. If the printer is not yet detected, connect
the machine and the computer with a USB cable, then select  Refresh.
•
If the printer is being used from another computer, a screen is displayed informing you of this
condition.
Note
•
This item has the same function as  Update in the Canon IJ Network Tool  screen.
Network Information Displays the  Network Information  screen to confirm the network settings of the printer and the
computer.
Network Information Screen
Display Warning Automatically Enables or disables automatic display of the instruction screen.
When this menu is selected, the instruction screen is displayed if one or more ports are unavailable for printing.
3.
Settings  menu
Configuration... Displays the  Configuration  screen to configure settings of the selected printer.
Configuration Screen
Note
•
This item has the same function as  Configuration... in the Canon IJ Network Tool  screen.
Enable switch printer function When you cannot use your printer, you can use the same one on the network instead. When you
enable this function and you cannot use your printer, the screen to confirm if you start searching
the same printer as yours is displayed. Follow the message on the screen.
Note
•
When this function is enabled, a check mark appears on the menu.
Associate Port... Displays the  Associate Port  screen and you can associate a port with the printer.
Associate Port Screen
This menu is available when  No Driver is displayed for the selected printer. Associating a port
with the printer enables you to use it.
231 
						

							Maintenance...Displays the  Maintenance  screen to revert the network settings of the printer to factory default
and to mount the card slot as the network drive.
Maintenance Screen
Set up printer's wireless LAN... You can change the access point mode settings. Perform settings following the message on thescreen.
If you change the  Encryption Method:  setting and the Password: setting on the  Set up printer's
wireless LAN  screen, the changed settings are applied to the printer settings.
Note
•
You can use this function only when you are using a computer compatible with the wireless LAN.
4.
Help menu
Instructions Displays this guide.
About Displays the version of IJ Network Tool.
232 
						

							Status ScreenYou can check the printer status and connection performance.
To display the  Status screen, select  Status from the  View menu.
Note
•
This screen is not available depending on the printer you are using.
•
When using wired LAN,  Signal Strength:, Link Quality:  and Advanced Measurement...  are not
available.
1.
Device Status:
The device status is displayed as  Available or Unavailable .
2.
Signal Strength:
Indicates the strength of the signal received by the printer, ranging from 0% to 100%.
3.
Link Quality: Indicates the signal quality excluding the noise while communicating, ranging from 0% to 100%.
4.
Advanced Measurement...
To examine the connection performance between the printer and the access point or between the printer
and the computer.
When you click, the  Connection Performance Measurement  is displayed.
Connection Performance Measurement Screen
233 
						

							Connection Performance Measurement Screen
Note
•
This screen is not available depending on the printer you are using.
Displays to execute the connection performance measurement.
Connection Performance Measurement Screen (Initial Screen)
Connection Performance Measurement Screen (Completion Screen)
Connection Performance Measurement Screen (Initial Screen)Click  Next>  to start measurement.
Connection Performance Measurement Screen (Completion Screen)
Displays when the measurement is finished.
234 
						

							1.Connection Performance between the Printer and the Access Point:
A mark indicates the result of the connection performance measurement between the printer and the access point.
: Good connection performance
: Unstable connection performance
: Cannot connect
: Measurement is canceled, or cannot measure
2.
Remeasurement
Measures the connection performance again.
Note
•
If any messages appear on  Overall Network Performance: , move the machine and access point as
instructed to improve the performance.
235 
						

							Maintenance ScreenDisplays to perform  Setting Initialization  and Network Setup of the Card Slot .
To display the  Maintenance screen, select  Maintenance...  from the Settings menu.1.
Setting Initialization
Reverts all the network settings of the printer to factory default. Click  Initialize to display the  Initialize
Settings  screen and click  Yes to initialize the network settings of the printer. Do not turn off the printer
during initialization. Click  OK when initialization is complete.
Performing initialization when connected over wireless LAN will break the connection, so perform setup with the Setup CD-ROM or perform setup according to the instructions on our website.
2.
Network Setup of the Card Slot
Note
•
This item is not available depending on the printer you are using.
Status  displays whether the card slot is mapped as a network drive.
When you click, the  Network Setup of the Card Slot  is displayed.
Network Setup of the Card Slot Screen
236 
						

							Network Setup of the Card Slot Screen
Note
•
This screen is not available depending on the printer you are using.
Displays settings of the card slot and allows you to map a card slot on the network as a network drive on the
computer.
Displays when you click  Setup on the  Maintenance  screen.
Network Setup of the Card Slot Screen (Setup Screen)
Network Setup of the Card Slot Screen (Setup Failed Screen)
Note
•
You can change the network settings of the printer using IJ Network Tool with USB connection after
initializing the LAN settings. To change the network settings using IJ Network Tool, activate the LAN
settings in advance.
Network Setup of the Card Slot Screen (Setup Screen)
1.
Drive:
Select the drive letter to assign to the network drive.
2.
Update Reloads the drive letters that are unassigned in  Computer (My Computer  in Windows XP) and
displays them in the  Drive: list.
Network Setup of the Card Slot Screen (Setup Failed Screen)
Display when the network setup of the card slot is failed.
237 
						

							1.
Skip
Completes the setup without mapping a network drive to the card slot.
2.
Retry
Returns to  Network Setup of the Card Slot  screen and re-executes the network drive mapping.
3.
Cancel
Cancels the card slot setup. When IJ Network Tool is running over LAN, the  Cancel button is
displayed grayed out and cannot be clicked.
238 
						

							Associate Port ScreenAllows you to associate a created port with a printer driver.
Select the printer for which you want to change the association, then click  OK.
Note
•
You cannot print with the printer unless the printer driver is associated with the port.
1.
Model:
Displays the name of device specified as a destination port.It is blank if the name of device is not detected.
2.
Printer:
Displays the printer driver installed in the computer. Select the printer for which you want to change the association.
3.
OK
Performs association.
239 
						

							Network Information ScreenDisplay the network information that is set for the printers and the computers.
To display the  Network Information  screen, select Network Information  from the View menu.1.
OK
Returns to the  Canon IJ Network Tool  screen.
2.
Copy All Information
All network information displayed is copied to the clipboard.
240