Carrier Tstatccphp01b Installation Manual

							PROGRAMMING THE  THERMOSTAT
The word COOL flashes on the display.
6Press the UP and DOWN buttons 
to adjust the cooling temperature setting 
listed in your personalized comfort schedule.
NOTE:  Don’t forget, your COOL setting must be at
least 2° higher than your HEAT setting. Your ther-
mostat will automatically change your previously
set temperature to maintain that 2° difference.
7Press the PROGRAM button to 
advance to the next time period. Following 
your personalized comfort schedule, enter 
times and temperatures for DAY, EVE, and
SLEEP time periods. 
You have now programmed 1 day into your
thermostat. At this time, you can 
either repeat steps 1-7 until all days of the 
week have been programmed, OR you can 
copy the schedule onto the remaining days of 
the week. See the section on ”Copying a 
daily schedule“ for details.
7 
						

							PROGRAMMING THE  THERMOSTAT
NOTE:  During programming, if you have not
touched a button or made an entry within 3 
minutes, the programming mode will automatically
shut off. Anything you have programmed will 
be saved.
8Press the END button when 
you finish entering your comfort schedule.
NOTE:  Once you’ve programmed your comfort
schedule, the thermostat will continue operating on
that program until you enter an alternative 
schedule. It may be appropriate to adjust 
temperatures as seasons change.
Copying a daily schedule
Typically, your Monday through Friday
comfort schedule will be the same. That’s
why the thermostat includes a COPY 
PREVIOUS DAY button. When 
programming, this eliminates the need to
re-enter identical information for each day. 
1Program a daily schedule.
Suggestion:  Start with Monday so the 
following 4 days can be copied.
2Press the CHANGE DAY button 
to move to the next day.
8 
						

							PROGRAMMING THE  THERMOSTAT
3Press the COPY PREVIOUS DAY 
button.
The previous day’s schedule will be entered 
into the new day.
4Continue this process by repeating
steps 2 and 3.
9 
						

							OPERATING THE  THERMOSTAT
Changing your comfort schedule
1Press the PROGRAM button to 
begin the programming process.
2Make necessary changes by 
following previous sections.
3Press the END button to 
end the programming process.
NOTE:  Entering new information always deletes
the old selections. Refer to the table of contents 
at the front of this guide to locate the type of 
programming you desire.  
Overriding your comfort schedule
There are 2 ways to override the existing
program. 
1Pressing the HOLD button.
By pressing the HOLD button, the 
thermostat will maintain the current 
temperature settings and ignore the comfort 
schedule for an indefinite period of time. 
The word HOLD will appear in the display.
Press the HOLD button a second time and 
the thermostat will resume normal 
operation, returning the temperature settings 
to the programmed comfort schedule. The 
thermostat will change the temperature 
setting as needed upon the next program 
10 
						

							OPERATING THE  THERMOSTAT
cycle. Pressing HOLD will not 
permanently alter your set program.
4Pressing the UP or DOWN buttons.
By pressing the UP or DOWN button, the 
current temperature settings appear on the 
display. Pressing the UP or DOWN button 
again will temporarily change the temperature 
setting above the flashing indicator as needed. 
To change the other setting for this time 
period, press the SET TIME/TEMP button until 
the other setting indicator flashes.  Pressing the 
UP or DOWN button again will temporarily change the other temperature setting as 
needed. The thermostat will automatically 
restore the comfort schedule settings at the 
next programmed time.
Checking the outdoor temperature
1Press the UP and DOWN buttons 
simultaneously.
11 
						

							OPERATING THE  THERMOSTAT
2The outdoor temperature will appear on 
the display.
NOTE:  If 2 dashes (--) appear, your 
thermostat does not include the outdoor 
temperature sensor or the sensor is not working
properly. Check with your dealer if you are unsure.
Checking current programmed time
and temperature settings
1Press the PROGRAM button.
2The current time and temperature settings 
for the current day and time period are 
displayed for you to check.
3Press the PROGRAM button again 
to advance to the next time period for same 
day. Continue this process to review all 
settings for the day.
4Press the CHANGE DAY button to 
view the next day’s settings.
12 
						

							OPERATING THE  THERMOSTAT
5Repeat steps 3 and 4 to review entire 7 day 
schedule.
CAUTION:  Pressing any other buttons while reviewing
current selections could alter the set program.
6Press the END button to 
exit the program mode.
Checking current temperature
The thermostat will display current 
temperature. To view your current 
temperature settings, press the UP or
DOWN button once. The heat and cool
temperature settings will be displayed.
Clean filter feature
Your thermostat reminds you when it’s
time to change or clean your filter by 
displaying the CLEAN FILTER indicator.
1Press the RESET FILTER button 
after you have changed or cleaned your filter 
to restart the timer.
13 
						

							AUTO CHANGEOVER
Your thermostat provides complete, 
automatic control over heating and 
cooling with auto changeover. Auto
changeover means your system will 
automatically heat or cool as needed to
maintain your temperature set points. Auto changeover makes life easier because
you no longer have to manually switch the
thermostat between heating or cooling
operation. Just set your heating and 
cooling set points and let the system do
the rest!
NOTE:  If auto changeover is not necessary
in your area of the country, your installer may 
disable the AUTO mode.
14 
						

							SMART RECOVERY
Smart recovery is a feature of your new
thermostat designed to save energy by 
gradually adjusting temperatures.
When it’s time for a programmed 
temperature change, smart recovery 
begins working in advance, turning the
system on and off as needed to slowly
adjust the indoor temperature. During
these transition periods, you may notice
that the actual temperature and your 
temperature setting don’t match. That’s
smart recovery in action, adjusting 
temperatures in small increments for
greater energy efficiency. This is moreenergy efficient than simply allowing the
system to operate at full capacity until the
desired temperature has been met.
NOTE:  The thermostat will start adjusting the 
temperature 1.5 hours before the scheduled 
temperature change. Smart recovery does not 
apply to cooling operation.
15 
						

							WHAT IF…
AUXILIARY HEAT indicator is displayed…
The AUX HT indicator appears on the heat
pump version of the 
thermostat only. It is displayed when your
system is operating on auxiliary heat.  
NOTE:  This indicator does not reflect a problem
with your system.
CLEAN FILTER indicator is displayed…
The CLEAN FILTER indicator tells you
when to clean or replace your system’s air
filter.  Press the RESET FILTER button after
cleaning or replacing the filter to turn off
the indicator and restart the timer.
NOTE:  This indicator does not reflect a problem
with your system.
HOLD indicator is displayed…
The HOLD indicator reminds you that
your thermostat’s comfort schedule has
been overridden. This function will hold the
current temperature settings indefinitely, so
it can be used to hold an energy-saving
temperature setting for several days if 
needed. Press the HOLD button to resume
normal system operation.
NOTE:  This indicator does not reflect a problem
with your system.
16