Cisco D9854i Manual

							 
 
 Control, Management and Data Interfaces 
 
78-4021470-01 Rev J 287 
 
Control, Management and Data Interfaces 
Ethernet Management Interface 
Item Specification 
Number of connectors 1 
Type of connector Eight-pin RJ-45 
Ethernet type 100/1000 BASE-T 
Required setup IP address, default gateway and subnet mask 
  
Ethernet Data Interface 
Item Specification 
Number of connectors 1 
Type of connector Eight-pin RJ-45 
Ethernet type 100/1000 BASE-T 
Required setup IP address, default gateway and subnet mask 
  
RS-232 Data Interface 
Item Specification 
Connector type 9-pin sub-D female 
Data rates RS-232 asynchronous data at selectable rates up 
to 38.4 kb/s: 300, 1200, 2400, 4800, 9600, 19,200, 
38,400 b/s 
  
Alarm Interface 
Item Specification 
Number of outputs 1, with one set of contacts closed and one set 
open during normal operation.  
Type of connector 15-pin sub-D female  
						

							 
Appendix A 
Technical Specifications 
288 78-4021470-01 Rev J 
Item Specification 
Max. voltage 40 V peak 
Max. current 0.5A 
  
Contact Closure Interface 
Item Specification 
Connector type 15-pin sub-D female 
Minimum duration of event 
guaranteed to be detected 
250 ms, 1 frame period, e.g., for 1080i/25 Hz 40 
ms for DPI applications 
Max. on generator impedance 100 ohms 
Min. off generator impedance 100 kilohms 
 
  
						

							 
 
 Power and General Specifications 
 
78-4021470-01 Rev J 289 
 
Power and General Specifications 
General 
Item Specification 
LCD 2 lines of 40 characters, backlit LCD. 
Keypad Arrow keys, 0 to 9, SELECT, MENU, INFO, 
ADV, MAP, APPLY and NAV keys. 
LEDs Green LED for Signal status. Red LED for Alarm 
indication. 
  
Power 
AC Power Connector 
Item Specification 
Type of connector IEC 320 style C14 appliance receptable 
AC input 100 to 240 V AC, 50/60 Hz 
Power 37 W max 
Current 0.34 A @ 240 V AC typical, 0.5 A @ 120 V AC 
typical 
Power Quality ANSI/IEEE Std C62.41.1-2002 
Power 
To operate the receiver, you must connect it to an AC power source. 
  
 
WARNING: 
Make sure that at least one end of the power cable(s) remains easily accessible for 
unplugging, if you need to switch off the unit. For example: Ensure that the socket 
outlet is installed near the product. 
 
  
 
WARNING: 
To avoid electrical shock, connect the three-prong plug on this product to an earth-
grounded three-pin socket outlet only. 
   
						

							 
Appendix A 
Technical Specifications 
290 78-4021470-01 Rev J 
Mechanical 
Item Specification 
Height  1 U (4.37 cm) (1.72”) 
Width  44.07 cm (17.35”) 
Depth 35.0 cm (13.78“) 
Weight 4.5 kg (10 lb.) 
  
Environment 
Item Specification 
Storage  
General The product is within the original packaging. 
Humidity 5 – 95% non-condensing 
Temperature  -20 – +70°C (-4 to 158°F) 
Operation  
Humidity (non-condensing) 95% humidity is valid up to 40°C 
91% humidity is valid up to 45°C 
70% humidity is valid up to 50°C 
Temperature  0°C – +50°C (32°F to 122°F) 
Altitude  
Operating  10,000 ft. (3048 m) max. 
Non-operating  30,000 ft. (9144 m ) max. 
 
  
						

							 
 
78-4021470-01 Rev J 291 
 
B Appx auto letter 
Appendix B 
Default Settings  
Introduction 
The D9854 Advanced Program Receiver is factory configured with 
default settings unless you have requested a custom factory 
configuration. This appendix lists the factory default settings.  
 
 
In This Appendix 
 Factory Default Settings ..................................................................... 292 
 DPM Default Settings for Different Output Modes ....................... 299  
						

							 
Appendix B 
Default Settings 
292 78-4021470-01 Rev J 
Factory Default Settings 
Administration 
Parameter Default 
Lock Level 0 
Password 1234 
KB Lock Disable 
KB Lock Timeout 60 
LCD Contrast 30 
DL Mode Always 
Date Format YYY_MM_DD 
Time Format 24 Hr 
GMT Off +05.30 
  
RF Input 
Parameter Default 
Tune Mode Basic 
CA Ctl Std 
Select UserCfg 
LO1 (GHz) 5.15 
LO2 (GHz) 0.0 
Crossover (GHz) 0.0 
OrbPos 0.0 
E/W NA 
Pol H (horizontal) 
Freq (GHz) 3.449 
Sym Rate 28.3465 MS/s 
FEC Auto 
Modulation DVB-S 
Roll-off .35  
						

							 
 
 Factory Default Settings 
 
78-4021470-01 Rev J 293 
 
Parameter Default 
InputIQ Auto 
NetID 1 
LNB Power Off 
22kHz Off 
  
Tune Mode 
Parameter Default 
Service List Mode Rigorous 
Frequency Tuning NIT 
Use BAT in Service List No 
Use NIT in Service List Yes 
Use SDT in Service List Yes 
Use PAT in Service List Yes 
  
IP 
Note: A factory reset does not change the IP settings. 
Parameter Default 
Port ID 1 
V4/V6 IPv4 
IP Address 192.131.244.6 
Mask 24 
Gateway 192.131.244.254 
SNMP Read Community 
String 
public 
SNMP Write Community 
String 
public 
Multicast Forwarding Forward All, if Port ID is set to 2 
SNTP Server 0.0.0.0 
SNTP Enable No  
						

							 
Appendix B 
Default Settings 
294 78-4021470-01 Rev J 
Parameter Default 
Password Complexity Full Complexity Checking 
  
Video 
Parameter Default 
PV Format Auto 
SD Format Auto 
Tri-Synch (Front Panel only) Disabled 
TV A/R 4:3 
Convert None 
WSS Mode Passthrough 
Enable Banner Display (Web 
GUI only) 
Enable 
  
Audio 
Parameter Default 
Stereo/Mono Stereo 
AC3 Compression RF Mode 
Left (dB) 0 
Right (dB) 0 
PMT Source AUD1 for Audio 1 and AUD2 for Audio 2 
DDP (Front Panel only) Trans 
Digital Out Pref PCM Samples 
  
Subtitles 
Parameter Default 
Op Mode Off 
Select Language By Language Entry 
Language List eng  
						

							 
 
 Factory Default Settings 
 
78-4021470-01 Rev J 295 
 
Parameter Default 
PMT Order First 
Entry eng 
Imitext Position Standard 
ForeGnd Auto 
BackGnd Auto 
  
CI 
Parameter Default 
Decrypt ON 
CI Slot Top 
Query Disabled 
Auto Reset Disabled 
List Mgmt AddDel 
TS_ON_ID Disable 
  
Cueing 
Parameter Default 
Cueing Mode Trigger 
Trigger Polarity High 
Repeat 3 
Tone (ms) 40 
Silence (ms) 40 
Relay Mode Alarm 
Cue Trigger Bit 1 
State Disable 
Mode * 
Delay (sec) 1 
   
						

							 
Appendix B 
Default Settings 
296 78-4021470-01 Rev J 
TS Out - ASI 
Parameter Default 
Name ASI 
Rate Control User 
User Rate 68.5 Mbps 
Output Mode No Output 
Descramble Mode Descrambled 
Insert Null Packet Yes 
  
TS Out - MOIP1 
Parameter Default 
Name MOIP1 
Rate Control User 
User Rate 0 
Output Mode No Output 
Descramble Mode Descrambled 
Insert Null Packet Yes 
Instance Name MPEG over IP 1 
MOIP UDP 
Send SAP No 
SAP ID Cisco Default SAP 
DestAddr 225.1.1.1 
UDPPort 49152 
SrcPort 0 
TS/IP 7 
Min IP/s 0 
PCR@IP Start Yes 
Mgmt Port Mode No Output 
DATA Port Mode Always output 
PCR Addition Yes