Honeywell K35891 Manual

 
– 11 – 
Functions of the Keypads 
 
1OFF
4MAX
7INSTANT
READY
2AWAY
5TEST
8CODE
03
STAY
6BYPASS
9CHIME
#
ARMED
READY
6160V-00-007-V0
MESSAGE
MICRECORD
VOLUME
PLAY
STATUS
VOICE
FUNCTION
12111087
9
132
34
6 5 1
18
17
16
15
14
20
19
 
 
Voice-capable 2-line Alpha keypad 
(shown with flip-down front door removed) 
 
IMPORTANT!  
• Match the numerical callouts in the above graphic with the corresponding number on the 
following pages for a description of usage. 
 When entering codes and commands, sequential...

 
– 12 – 
Functions of the Keypads (cont’d)  
NOTE: The functions printed directly on the 
keys indicate their primary purpose; the 
functions printed under some of the keys (shown 
in brackets under the respective key), indicate 
their alternate or secondary purpose. 
 
1. DISPLAY WINDOW  
 Alpha Display Keypads:  2-line, 32-
character Liquid Crystal Display (LCD) 
keypads that display protection point 
identification, system status, and 
messages.  
 Fixed-Word Display Keypads:  
 Display protection...

 
– 13 – 
 
Functions of the Keypads (cont’d)   
11. #         This key can be used for Quick 
Arming of the system without use of a 
security code (if programmed). 
[FUNCTION] On Voice keypads, enables 
the desired voice or volume function. 
12. 0       
  
[VOICE] On Voice keypads, enables the 
RECORD, VOLUME and PLAY 
functions.  
13. ∗
 READY Used to display all open 
protection zones.  
[STATUS] On Voice keypads, a 
momentary press of the STATUS key 
annunciates the current system status. 
Pressing...

 
– 14 – 
Entry/Exit Delays 
Entry Delay 
Entry Delays give you time to disarm the system when you re-enter through the 
designated entrance door. There are two entry delays (if programmed). The first is for 
your primary entrance and the second can be used for a secondary entrance, where a 
longer delay is required to walk to the keypad to disarm the system. 
 
You must disarm the system before the entry delay period ends, or an alarm will 
occur. The keypad beeps during the entry delay period,...

 
– 15 – 
Entry/Exit Delays (cont’d) 
 
Exit Alarms  
Exit Error Conditions 
Whenever you arm the system, the exit delay begins. If an entry/exit door or interior 
zone is faulted before exit delay expires and remains faulted (e.g., exit door left open), 
the system sounds an alarm and starts the entry delay timer. If you disarm the 
system before the entry delay ends, the alarm sound stops and the message ALARM 
CANCELED  or CA is displayed on the keypad, along with a zone number 
indicating the faulted...

 
– 16 – 
Checking For Open Zones  
Using the [∗
∗∗ ∗] Key to Display and Announce System Status 
Before arming your system, all protected doors, windows and other protection zones 
must be closed or bypassed; otherwise the keypad will display a Not Ready 
message.  
 
Use the READY key to display all faulted zones, making it easier for you to identify 
and secure any open zone. 
 
1. Press [✱] (do not enter code first) to display faulted 
zones. 
2.  Secure or bypass the zones displayed. 
 The keypad’s...

 
– 17 – 
Arming the System  
STAY Mode: Arms Perimeter Only, Entry Delay On 
•  Used when you want to arm the system with persons staying inside (or if you have 
pets that are moving throughout the premises). 
•  The door & window sensors are armed, but interior motion detectors are disarmed. 
•  Exit delay begins (you can leave through the entry/exit door, if desired). 
•  An alarm sounds if any protected window or non-entry/exit door is opened. 
•  You may otherwise move freely within the premises. 
•...

 
– 18 – 
Arming the System (cont’d)  
Arming Commands 
Before arming, close all perimeter doors and windows and make sure the Ready to Arm 
message is displayed.
 
Mode  Press these keys…  Keypad Confirms By… 
STAY security code + 3  STAY  
 • three beeps† 
• armed STAY message displayed 
• red ARMED indicator lights 
NIGHT-
STAY security code + 3  STAY + 3  STAY 
 • three beeps† 
• NIGHT-STAY message displayed 
• red ARMED indicator lights 
INSTANT security code + 7 INSTANT  
 • three beeps† 
• armed...

 
– 19 – 
Arming the System (cont’d) 
Single Button Arming 
The “A”, “B”, “C”, and/or “D” keys on your keypad may have been programmed for 
single-button arming. Note that while it is not necessary to use a security code for 
arming (by using the Quick Arm method described previously), a security code must 
always be used when manually disarming the system. 
 
If Single-Button Arming is programmed: 
•  A function key has been assigned to a specific type of arming: STAY mode, NIGHT-
STAY mode, AWAY mode,...

 
– 20 – 
Keyswitch 
 
Using the Keyswitch 
Your system may be equipped with a keyswitch for use when arming and disarming. 
Red and green lights on the keyswitch plate indicate the status of your system as 
follows: 
Green Light:  Lights when the system is disarmed and ready to be armed (no 
open zones). If the system is disarmed and the green light is off, it 
indicates the system is not ready (one or more zones are open). 
Red Light:  Lights or flashes when system is armed in AWAY or STAY mode. 
See...