Mitel SX 200 DIGITAL Pabx Shipping, Receiving, And Installation Information Manual

MITEL STANDARD PRACTICESECTION MITL9109-094-200-NAIssue 
1, April 1988
SX-200” DIGITAL
PRIVATE AUTOMATIC BRANCH EXCHANGE (PABX)
SHIPPING, RECEIVING, AND INSTALLATION INFORMATION
@Copyright 1988, MITEL Corporation. All rights reserved.
T”Trademark of MITEL Corporation
@Registered Trademark of MITEL Corporation 

SECTION MITLSI 09-094-200-NA
NOTICEThe information contained in this document is believed to be accurate in all respects but is
not warranted by 
Mite1 Corporation (MITEL). The information is subject to change without
notice and should not be construed in any way as a commitment by 
Mite1 or any of its
affiliates or subsidiaries. 
Mite1 and its affiliates and subsidiaries assume no responsibility
for any errors or omissions in this document. Revisions of this document or new editions of
it may be issued...

Shipping, Receiving, and Installation Information
CONTENTS
PAGE1. INTRODUCTION
General.............................................1
Reason for Issue......................................1
Notice to Installation Personnel...........................12. CONFIGURATION
General.............................................3
Welded Control Cabinet.................................
4
Universal Control Cabinet................................
4
672-port Control Cabinet................................4
Analog...

SECTION MITL9109-094-200-NACONTENTS (CONT’D)
PAGEDisk Handling Procedures . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
1306. CABLING AND CROSS-CONNECTIONS
General . . . . . . . . . . . . . . . . . . . . . . . . . . . .. . . . . . . . . . . . . . 133
Telephone Set and Trunk Cabling . . . . . . . . . . . . . . . . . . . . . . . .
133System Cable Terminations . . . . . . . . . . . . . . . . . . . . . . . . . . . . 133
7. UPGRADING AN EXISTING SX-200 PABX TO AN SX-200 DIGITAL PABX...

Shipping, Receiving, and Installation Information
CHARTTITLE
PAGE
5-15-2
5-3
5-4
5-5
5-6
5-7
5-8
5-9
5-10
5-115-12
5-13
5-14
5-15
5-16
5-17
5-18
5-19
5-20
5-21
5-22
5-23
5-24
5-25
5-26
5-27
5-28
5-29
5-30
5-31
5-32
5-33
7-l
8-1
Prepare System Configuration...................47
Unpack Equipment Cabinets and Equipment Except
Printed Circuit Boards.......................
48
Inspect Equipment............................
48
Install Control Cabinet.........................
50
Verify Ground...

SECTION MITLSI 09-094~200-NALIST OF ILLUSTRATIONS
FIGURETITLE
PAGE2-l
2-2
2-3
2-4
2-5
2-6
2-7
2-8
4-l
4-2
4-3
4-4
4-5
4-6
4-7
4-8
4-9
4-10
4-11
4-12
4-13
4-14
4-15
4-16
4-17
4-18
5-15-2
5-3
5-4
5-5
5-6
5-7
5-8
5-9
5-10
5-115-12
5-13
5-14SX-200 DIGITAL PABX Welded Control Cabinet........
5
SX-200 Universa! Control Cabinet.................6Universal Control Cabinet with Digital Peripheral Shelf . . 7
SX-200 DIGITAL PABX Peripheral Cabinet............8SX-200 672 port DIGITAL PABX Control Cabinet.......
9...

Shipping, Receiving, and Installation InformationFIGURE5-15
5-16
5-17
5-18
5-19
5-20
5-215-22
5-23
5-24
5-25
5-26
5-27
5-28
5-29
5-30
5-3 15-32
5-33
5-34
5-35
5-36
5-37
5-38
5-39
5-40
5-41LIST OF ILLUSTRATIONS (CONT’D)
TITLEPAGE
PFT Card Connections.........................
77
Charging Unit...............................
81
Reserve Power Supply.........................82Maintenance Terminal Connections 
- SX-200 Cabinet . 86
Maintenance Terminal Connections - SX-200 Universal...

SECTION MITL9109-094-200-NA 

Shipping, Receiving, and Installation Information
1. INTRODUCTIONGeneral
1.01This section provides a general identification, and shipping,
receiving, and installation procedures for the SX-2OU@ DIGITALPABX. The PABX consists of one or two cabinets. The 
Control cabinet
contains a control shelf and an optional peripheral shelf. The 2-cabinet
configuration consists of the Control cabinet, and a Peripheral cabinet
containing one or two peripheral shelves.Reason for Issue
1.02This Section is issued to...

SECTION MITL9109-094-200-NA
Page 2