Mitel Sx 50 Dpabx Instructions Guide
Have a look at the manual Mitel Sx 50 Dpabx Instructions Guide online for free. It’s possible to download the document as PDF or print. UserManuals.tech offer 55 Mitel manuals and user’s guides for free. Share the user manual or guide on Facebook, Twitter or Google+.
Customer Data Entry Forms COMMANDS 501 + 580 TRUNK PROGRAMMING TYPE: - Register 1 - Trunk Group Membership (1 - 6 = Trunk GroupNumber) (0 = Incoming Calls Only) -Trunk Alarm Control (0 = Disable, 1 = Enable) - Trunk Hardware Type 0 = Short Analog CO Trunk 4 = Satellite Tie Trunk 1 = Long Analog CO Trunk 5 = Short Analog DID Trunk 2 = Analog Toll Office Trunk 6 = Long Analog DIDTrunk ( 3 = Analog Tie Trunk - Trunk Class of Service (1 - 9) - Inward Dial Delay before Answer (8 set) (0 = Disable, 1 = Enable Note: this applies to all trunk types. - Connect to Outgoing Trunk without Third Party 0 = Disable, 1 = Enable Inward Dialing ARS Routing Class of Service (1 - 3) 0 = ARS does not apply r Trunk Use 0 = Disable 2 = Use as a Tie Trunk 1 =UseasaCO 3 = Used as a DID Trunk Trunk Dialing Type 0 = DIL, 1 = DISA, 3 = DID I Default 1 0 1 6 1 0 1 0 3 2 CO TRUNK E&M TRUNK DID TRUNK . . : 102 2-60 Revision 0 9104-091-l 02-NA Issue 3
Customer Data Entry Forms COMMANDS 501 - 580 TRUNK PROGRAMMING TYPE: SLOT: - Register 2 - Trunk Outpulsing Break/Make Ratio 0 = 60140 1 = 65135 2 = 30120 3 = 35115 - Disconnect Supervision Guaranteed? 0 = No, 1 = ?es - Disappearance of Reversal 0 = is ignored 1 = means disconnect - Reversal Meaning on Call Origination 0 = Not Incoming Call 1 = Incoming Call - Disconnect Timing 0 = 60 ms 3 = 4.0 set 1 = 500 ms 4=10.Osec 2 = 1.5 set 5 = Disconnect Ignored Start Type (CO Trunks) 0 = Loop Start 1 = Ground Start r Trunk Hang-up Delay (Guard) Timer 01 -+16=1 +16seconds L l- L -I- l- J I I---l l- lCommandlalbjcldlejf lglhl i 5 2 - 5- 2 5- 2 5- 2 5 2 - I 5-14 I I I I I I I I 5 2 - 5- 2 Default 200001001 9104-091-l 02-NA Issue 3 Revision 0 102 2-61
Customer Data Entry Forms COMMANDS 561 - 580 TRUNK PROGRAMMING TYPE: - Register 3 Command a bl “I - Tie Line Disconnect Timer 0=150ms 1 = 300 ms -E&M Lead Inversion Type 1 Type 5 o= M-Lead None l= ‘Both E-Lead 2= None M-Lead 3= E-Lead Both l- -E&M Delay Dial Outgoing 0 = Disable 1 = Enable - E&M Wink Start Incoming 0 = Disable 1 = Enable -r 7 - E&M Wink Start Outgoing 0 = Disable 1 = Enable RESERVED I I dlelflgl I Default 131112101010121 102 2-62 Revision 0 9104-091-l 02-NA Issue 3
Customer Data Entry Forms COMMANDS 501 - 580 TRUNK PROGRAMMING - Register 4 TYPE: - Dictation Trunk (for LS/GS Trunks) 0 = Disable 1 = Enable - Inter-ringing Delay (for KS/GS Trunks) 5 - 4 5 - 4 Default 4 0 5 1001000* 3 - 9 seconds -Day Answer Mode Day Illegal Number Intercept (DID/DISA) 0 = Direct-In Line 1 = LDNl 2 = LDN2 3 = LDN3 - Day Answer Point (Day Answer Mode = 0) Day Inward Dial Trunk Intercept Answer Point (DID/DISA) 000 = Night Bell 001 -+ 160= Station Number 161 + 166= Hunt Group Number 167= Ring Group 168= RMATS - Busy Intercept 0 = Disable 1 = Enable - Do Not Disturb Intercept 0 = Disable 1 = Enable - No Answer Intercept 0 = Disable 1 = Enable Illegal/Vacant Number Intercept 0 = Disable 1 = Enable * = 0 for CO & DID Trunks; 1 for E&M Trunks 9104-091-l 02-NA Issue 3 Revision 0 102 2-63
Customer Data Entry Forms COMMANDS 561 - 580 TRUNK PROGRAMMING TYPE: Night answer Mode Night illegal Number Intercept (DID/DISA) 0 = Flexible Night Service 1 = LDN 1 2=LDN2 3=LDN 3 _ 5 Register 5 -Night Answer Point (Night Answer Mode = 0) Night Inward Dial Trunk Intercept Answer Point (DID/DISA) 000 = Night Bell 001 - 160 = Station Number 161 - 166 = Hunt Group Number 167= Ring Group 168= RMATS r DID Night Answer Point 0 = Disable 1 1 = Enable e f I I I I 102 2-64 Revision 0 9104-091-l 02-NA Issue 3
Customer Data Entry Forms COMMANDS 501 - 580 TRUNK PROGRAMMING - Register 6 - DID Start Type 0 = Immediate Start 1 = Wink Stat-l 2 = Delay Dial - RESERVED - Incoming Address Signalling 0 = LoopDial Pulsing 1 = Battery-and-Ground Pulsing 2 = DTMF - N = Number of Digits Expected (1 - 9) - M = Number of Digits to be Absorbed (0 - 8) Digits to be Inserted 5 6 - 5- 6 Default 6 1 1 0 4 1 TYPE: 9104-091-l 02-NA Issue 3 Revision 0 l-02 2-65
Customer Data Entry Forms COMMANDS 501 + 580 TRUNK PROGRAMMING TYPE: r - Register 7 -r - Incoming Seizure Debounce Timer (01 - 15) x 10 ms - WinkTimer (3 + 6) x 50 ms - Permanent-Signal Partial-Dial Timer .(I +6)x5s - DID Disconnect Timer (3-6)x50ms Release Acknowledge Timer 002+12os l- a 1 b 1 c 1 d I e I f I g I h I i I 5 7 - 5 - 7 I Default I 7 I I I I I o I 4 I I I, I I I 102 2-66 Revision 0 9104-091-l 02-NA Issue 3
Customer Data Entrv Forms COMMAND 600 VERIFIED AUTHORIZATION CODE PROGRAMMING L I l- l- 11 DEFAULT VALUES - Register Number: 001 +.999 - VAC Activation: 0 = Disable, 1 = Enable - CDS for Authorization Code 0 = Disable, 1 -j 9 = COS 1 - 9 (for VAC) - ARS Routing Nilmber 1 +3=ARSRCSl -3(forVAC), 0 = Original RCS Number of Calling Device Authorization Code (1 to 8 digits) 9104-091-102-NA Issue 3 Revision 0 102 2-67
Customer Data Entry Forms COMMAND 700 ARS DIGIT COMPARISON TABLE PROGRAMMING r Entry Number 001 - 800 r Time-of- Day Table Number 01 -45 [ 1 [ . . 1 1 I 1 1 102 2-68 Revision 0 9104-091-l 02-NA Issue 3
Customer Data Entry Forms COMMA-NDS 701 - 745 ARS TIME-OF-DAY TABLE PROGRAMMING COMMAND 7 CO-MMAND 7 - -. I- r a 1 1 2 - Period Number - Start Hour 00 - 23 - Start Minute 00 + 59 Route List 001 + 200, 000 = not programmed RCS 1 Route List RCS 2 Route List RCS 3 Route List Ill I I I I I elf 1 al hl iI iI kl I Iml nl - Period Number - Start Hour 00 - 23 . - Start Minute 00 - 59 Route List 001 + 200, 000 = not programmed RCS 1 Route List RCS 2 Route List RCS 3 Route List I 1 I I I I I cldlelf I al hl i jI k llmln I I I - - ., _ - 0 0 0 0 0 0 0 0 0 Default - - - - 0 0 0 0 0 0 0 0 0 Default 9104-091- 02-NA Issue 3 Revision 0 102 2-69