Mitel Sx 50 Dpabx Instructions Guide

							Automatic Route Selection and Toll Control 
ARS Digit Modification Table (Command 752) 
There is a maximum of 100 Digit Modification Table (DMT) entries. The Register Number is the 
Entry Number, which is referenced from the Route Table. Each DMT Entry defines how many 
digits are to be deleted from the dialed digit string and what digits are then to be added. (The 
first digit entered is the first deleted). 
The fields which comprise the Digit Modification Table are described below. 
DMT Entry Number: 
This nonprogrammable field is the DMT Entry Number. 
No. of Digits to Delete: This field lists the number of digits the system deletes from 
the dialed digit string. Valid entries are 0 to 12. 
Digits to insert: This field lists the digits that the system prefixes to the dialed digit 
string after the specified digit deletion has occurred. Included in the modifying digits are 
the PAUSE and WAIT FOR DIAL TONE characters. The system accepts a maximum 
of 20 digits per DMT Entry Number. 
Associated with thisform are two softkeys that perform special functions: 
l VIEW: Pressing the VIEW softkey scrolls the digit string display one digit to the left. 
By repeated presses of this key, the user can view the entire 2O-digit string. 
l DELETE: Pressing the DELETE softkey deletes the digit string digits from the cur- 
rent position to the end of the digit string. 
These soft keys appear when the first digit of the digit string is entered: 
l PAUSE: Pressing the PAUSE softkey or dialing *7 inserts a 5--second pause in the 
digit string. The Attendant Console LCD shows the P character for each pause. 
l WFDT: Pressing the WFDT softkey or dialing *‘6 halts the outpulsing of the digit string 
until Dial Tone is returned. The Attendant Console LCD shows the W character each 
time the WFDT softkey is pressed. 
220 5-6 Revision 0 9104-091-220-NA Issue 5  
						

							SX-50@ DIGITAL PRIVATE’ 
AUTOMATIC BRANCH EXCHANGE 
(DPABX) 
Addendum 
Package (MR4)  
						

							Addendum Package 
NOTICE 
The information contained in this document is believed to be accurate in all 
respects but is not warranted by Mite1 Corporation (MITEL@). The informa- 
tion is subject to change without notice and should not be construed in any 
way as a commitment by Mite1 or any of its affiliates or subsidiaries. Mite1 
and its affiliates and subsidiaries assume no responsibility for any errors or 
omissions in this document. Revisions of this document or new editions of it 
may be issued to incorporate such changes. 
Revision 0 9104472-019-NA Issue 1  
						

							1 
’ INTRODUCTION 
General 
1.1 After the successful mechanical installation of the SX-50s system (refer to Section 
9104-091-200-NA, Shipping, Receiving and Installation Information), the system is 
ready for programming. This Section provides forms for the installer to record 
customer data. For information on programming options and access to CDE from the 
Console or Test Line, refer to Section 9104-091-210-NA. 
Reason for Reissue 
I 
1.2 Section 9106091-102-NA, Customer Data Entry Forms, has been reissued to 
include a description of the SUPERSET’” 410 and 
SUPERSET 420 telephones, the 
Digital Network interface Circuit (DNIC) Line Card and the functionality provided by 
MS55 software. 
9104-091-l 02-NA Issue 3 
Revision 0 102 l-l  
						

							Customer Data Entrv Forms 
102 l-2 Revision 0 9104-091-l 02-NA Issue 3  
						

							1 
’ INTRODUCTION 
General 
1.1 The Documentation Index lists the MITEL Standard Practices included in the SX-508 
.DPABX Communications documentation. Each practice forms a section of the 
system documentation. A brief description of each section is given. 
Reason for Reissue 
1.2 This Section is reissued to incorporate MS55 modifications. 
The following Section is added: 
l 9104-091-I 50-NA, Ordering Information. 
9104-091-01 C+NA Issue 5 Revision 0 010 l-l  
						

							Documentation Index 
010 l-2 Revision 0 9104-091410-NA Issue 5  
						

							2 . 
DOCUMENTATION 
General 
2.1 The SX-50 system documentation is contained in one volume. Contents are listed in 
Table 2-l. 
Description of Sections 
2.2 The content of each Section is as follows: 
(a) 9104-091-001-NA, Control Sheet, is identified by a unique part number, and iden- 
tifies the issue of each standard practice contained. 
(b) 9104-091--Ol O-NA, The Documentation Index lists the MITEL Standard Practices 
included in this SX-50 DPABX Communications System documentation. 
(c) 9104-091-l 00-NA, General Description, contains a brief description of the SX-50 
system. 
(d) 9104-091-l 02-NA, Customer Data Entry Forms, contains blank programming 
forms. This Section can also be-ordered separately. 
(e) 9104-091-l 05-NA, Features Description, describes the features available on the 
SX-50 system. Each feature description-details: 
l programming required, conditions affecting the feature, and feature operation. 
(9 9104-091-l 50-NA, Ordering Information, lists those parts which are orderable for 
the SX-50 system. 
(g) 9104-091-l 80--NA, Engineering Information, contains technical information relat- 
ing to the SX-50 system. 
(h) 9104-091-200-NA, Shipping, Receiving, and Installation Information, provides 
the correct procedures for installation of the SX-50 system. 
(i) 9104--091-210-NA, Customer Data Entry, describes how to program the SX-50 
system to meet the customer’s requirements. 
(j) 9104-091-220-NA, Automatic Route Selection and Toll Control Description, con- 
tains a description of the Automatic Route Selection (ARS) and Toll Control 
package the SX-50 system provides. 
(k) 9104-091-221-NA, Station Message Detail Recording (SMDR), describes 
SMDR, including printer installation and system programming. 
9104-091-010-NA Issue 5 Revision 0 010 l-l