Panasonic Digital Disk Recorder Wj Hd616 Wj Hd716 Installation Guide

							101
Configure	the	settings	relating	to	DNS	[DNS]
Select the [DNS] tab on the "Network" page. (+ Page 60)
The settings relating to DNS (Domain Name System) can be configured on this tab. 
    
[DNS]
Determine whether or not to use the DNS. 
   Off/Auto/Manual
	 •	 Select	"Manual"	or	"Auto"	to	enable	IP	address	 searching by the host name using the DNS. 
	 •	 Select	"Off"	when	not	using	the	DNS.	
	 •	 Selecting	"Auto"	is	available	only	when	"On"	is	 selected for "DHCP" (using the DHCP server). 
	 •	 Selecting	"Manual"	is	available	regardless	of	the	set- ting for "DHCP" (with or without using the DHCP 
server). 
	 •	 When	"Manual"	is	selected	for	the	DNS,	enter	the	 DNS server addresses in "Primary server address" 
and "Secondary server address".
[Primary	server	address],	[Secondary	server	address]
Enter the IP address of the primary DNS server and second-
ary DNS server. Enter 4 units from the decimal numbers 
(0-255).
Default: 0.0.0.0
[Domain	name]
Enter the domain name of this recorder. The first character of 
the domain name should be an alphabetical character. The 
first character of the domain name should be an alphabetical 
character.
Enter 3 to 63 alphanumeric characters including hyphens (-) 
and periods (.).
Default: localdomain
     
						

							102
Configure	the	settings	relating	to	DDNS	[DDNS]
Select the [DDNS] tab on the "Network" page. (+ Page 60)
The settings relating to DDNS (Dynamic Domain Name System) can be configured on this tab. 
    
[DDNS]
Select "On" or "Off" to determine whether or not to use the 
DDNS. 
When "On" is selected, configure the following settings. 
[User	name]
Enter a user name registered in the DDNS. 
Enter up to 32 alphanumeric characters excluding "&" listed 
in the description of "Available characters" (+ page 96). 
[Password]
Enter the password registered together with the user name. 
Enter up to 32 alphanumeric characters excluding "&" listed 
in the description of "Available characters". Enter up to 32 
alphanumeric characters excluding "&" listed in the descrip-
tion of "Available characters" (+ page 96). 
[Access	interval]
Select an interval to update the DNS from the following:
   10 min/30 min/1 h/6 h/24 h
Default: 1h
[Host	name]
Enter a host name registered in the DDNS. Enter up to 255 
alphanumeric characters including hyphens (-) and periods 
(.). 
Important:
	 •	 It	is	impossible	to	set	a	host	name	if	the	first	character	of	 the entered host address is a numerical character or 
symbol. 
 
     
						

							103
Configure	the	settings	relating	to	SNMP	[SNMP]
Select the [SNMP] tab on the "Network" page. (+ Page 60)
The settings for the SNMP can be configured on this tab. The settings are configured to check the status of the recorder, etc. by 
connecting the SNMP manager.
    
[Community]
Enter a name used for SNMP authentication in alphanumeric 
characters. Enter up to 32 alphanumeric characters exclud-
ing "&" listed in the description of "Available characters". (+ 
Page 96) 
[System	name]
Enter a system name in alphanumeric characters to manage 
this unit by the SNMP system, for example, No1. Enter up to 
255 alphanumeric characters listed in the description of 
"Available characters" (+ page 96). 
[Location]
Enter the name of the location where the camera is installed, 
for example, 2F. Enter up to 255 alphanumeric characters 
listed in the description of "Available characters" (+ page 
96). 
[Contact]
Enter the contact information such as a mail address of an 
administrator of this recorder. Enter up to 255 alphanumeric 
characters listed in the description of "Available characters". 
Enter up to 255 alphanumeric characters listed in the 
description of "Available characters" (+ page 96).  
						

							104
Configure the Panasonic alarm protocol settings  
[Panasonic	alarm	protocol]
Select the [Panasonic alarm protocol] tab on the "Network" page. (+ Page 60)
The settings to notify the PC of the event and error information when an event or an error occurs can be configured on this tab. 
To display the event and error information, it is necessary that the dedicated software is installed on the PC.
Refer to the "readme.txt" file on the CD-ROM for details about the software.
    
[Port	number	(to	PC)]
Enter the addresses of the recipient PCs.
Default: 01818
[Retry]
Set the number of retry attempts for the transmission to the 
PC. 
   0 to 8 (times) (In steps of times)
Default: 2
■  Destination address
[Address1	to	Address8]
Enter the addresses of the recipient PCs. Enter the IP 
address or host name for "Address 1" - "Address 8".
The host name is available only when selecting "Manual" or 
"Auto" for the "Network" page - the [DNS] tab.
Up to 8 destinations can be registered.
Enter up to 255 alphanumeric characters including hyphens 
(-) and periods (.).
     
						

							105
Configure	the	settings	relating	to	network	transmission	[Transmission]
Select the [Transmission] tab on the "Network" page. (+ Page 60)
The settings relating to the resolution and rate to transmit live images to a PC via a network can als\
o be configured on this tab. 
    
[Live	video	resolution]
Select the resolution for live images from the following. REC resolution: Live images are transmitted with the resolution applied at the time of recording. 
QVGA: Live images are transmitted in the QVGA size. 
Default: REC resolution:
[Live	video	rate(rec	resolution)]
Select the image transmission rate of live images (activated 
when recording is not performed) when "REC resolution" is 
selected for "Live video resolution". During recording, record-
ing rate is activated for live image transmission.
    Off/ 1.25ips/ 2.5ips/ 3.75ips/ 7.5ips/ 15ips (Only for 
HD716K)
Default: 7.5ips
[Live	video	quality(rec	resolution)]
Select the image quality of live images (activated when 
recording is not performed) when "REC resolution" is select-
ed for "Live video resolution". During recording, recording 
image quality is activated for live image transmission. XF	(Extra	Fine): Extra quality
SF (Super Fine): Super high quality
FQ (Fine): High quality
NQ (Normal): Standard quality
EX	(Extended): Low quality (for long recording)
Default: FQ
[Live	video	rate(QVGA)]
Select the transmission bit rate when "QVGA" is selected for 
"Live video resolution".
    128Kbps/192Kbps/256Kbps/384Kbps*/512Kbps*
    * Only for HD716K
Default: 256Kbps
[Bandwidth	control]
Select the maximum transmission rate for data to be trans-
mitted from the following.
    Unlimited/512Kbps/1 024Kbps/2Mbps/3Mbps/5Mbps/ 
8Mbps
Default: Unlimited
    
Note:
	 •	 Regardless	of	the	setting	for	"Live	video	resolution",	 when images are displayed on a multiscreen (4-split/ 
9-split/16-split screen) or with the sequential display, 
"QVGA" is activated for resolution, and the setting for 
"Live video rate (QVGA)" is activated when image is 
transmitted.
	 •	 When	image	is	displayed	on	a	single	screen,	the	setting	 for "Live video resolution" is activated when image is 
transmitted.
	 •	 The	settings	for	"Live	video	rate(rec	resolution)",	"Live	 video quality(rec resolution)" and "Live video rate(QVGA)" 
are applied to each screen segment.
Example: When "128Kbps" is selected for "Live video rate (QVGA)" while images are being displayed on a 
4-split screen, the whole transmission rate is  
512 Kbps.
	 •	 Select	the	setting	for	"Bandwidth	control"	so	that	the	 value is greater than the total rate required for network 
transmission. When the setting value is less than the 
total transmission rate, image data may be destroyed 
during transmission.
Example: When "QVGA" is selected for "Live video res-olution" and "128Kbps" is selected for "Live video 
rate (QVGA)" while 4 PCs displaying a single screen 
are accessing the recorder simultaneously, select the 
value greater than "512Kbps" for "Bandwidth con-
trol". 
    When "REC resolution" is selected for "Live video resolu-
tion", it is recommended to set "Unlimited" for 
"Bandwidth control" to prevent the images from destruc-
tion due to change in transmission rate caused by the 
recording setting. When images are destroyed even 
when "Unlimited" is selected for "Bandwidth control", 
select a lower value for image quality or recording rate. 
						

							106
The settings relating to the user authentication On/Off, PSD user, administrator registration and operation levels can be config-
ured on the "User mng." page. It is possible to restrict users and hosts (PCs) to access the recorder by registering the users and 
hosts (PCs) who can access the recorder in advance when "On" is selected for the user authentication and the\
 host authentica-
tion. 
The "User mng" page has [Basic], [Administrator], [User], [Host] and [Us\
er level] tabs. 
Configure	the	basic	settings	relating	to	user	management	[Basic]
Select the [Basic] tab on the "User mng." page. (+ Page 60)
The setting can be configured on this tab to determine whether to enable or disable the user authen\
tication and the host authen-
tication for network operation, the settings relating to the login users who operate the recorder using the buttons on the front 
cover of the recorder and the settings relating to the users who operate the recorder using the PS·Data compatible controllers. 
    
Configure	the	settings	relating	to	the	user	management	[User	mng.]
■ Network
Determine whether to enable or disable the user authentica-
tion and the host authentication when operating the recorder 
using a PC via a network. 
[User	authentication]
Select "On" or "Off" to determine whether or not to authenti-
cate the user. 
[Host	authentication]
Select "On" or "Off" to determine whether or not to authenti-
cate the host. 
■ Front panel
Configure the settings to enable the auto login function that 
starts the recorder automatically when the power of the 
recorder is turned on.
[Auto	login	user]
When "On" is selected for "Auto login", the user registered 
as auto login user in this setting can log into the recorder 
automatically. An auto login user should be one of the users 
registered in the recorder. 
Default: ADMIN
[Auto	login]
Select "On" or "Off" to determine whether to activate or 
deactivate the auto login function. 
    
Off: Does not log in to the recorder automatically. Login 
is required when operating the recorder from the 
logout status. 
On: Logs in to the recorder automatically
Default: On
[Auto	logout]
Configure the settings to log out a user automatically when 
the set time has passed from the time a user logged in. 
    Off/1 min/2 min/3 min/4 min/5 min/30 min:
Default: Off
Note:
	 •	 When	"On"	is	selected	for	"Auto	login",	the	user	will	not	 be logged out automatically even if "1 min", "2 min",  
"3 min", "4 min", "5 min" or "30 min" is selected for 
"Auto logout".
	 •	 To	prevent	inappropriate	operations,	it	is	recommended	 to select "On".
[Quick	login]
Select "On" or "Off" to determine whether to enter or select 
the user name . Off: Enters a user name.
On: Selects a user name.
Default: On
     
						

							107
Register	or	change	the	administrator	information	[Administrator]
Select the [Administrator] tab on the "User mng." page. (+ Page 60)
The administrator information relating to the password and default screen, etc. can be registered on this tab. 
To change the administrator information that has been registered, select the [Edit] button after changing each setting item. 
    
[Administrator	name]
Enter an administrator name. Enter 5 to 8 alphanumeric 
characters for the administrator name. Enter 5 to 14 alpha-
numeric characters for the administrator name.
[New	password]
Enter a password for an administrator. Enter 5 to 8 alphanu-
meric characters for the administrator name.Important:
	 •	 For	enhanced	security,	change	the	password	on	a	regu- lar basis. Change the password periodically. 
 
[Retype	new	password]
Enter the password that has been set for "New password" 
again for confirmation. 
[Level]
Display the operation level of an administrator. It is impossi-
ble to change the setting value for an administrator. "0" has 
been set for the administrator. 
[Access	priority]
Displays the settings to assign priorities to operate the 
recorder in case two or more users access the recorder 
simultaneously. 
It is impossible to change the setting value for an administra-
tor. "0" has been set for the administrator. 
    [Default	screen]
Select a startup display to be displayed after login from the 
following.  Cam.1 to 16: Displays an image from the selected cam-era channel on a single screen.
    4Screen-A/4Screen-B/4Screen-C/4Screen-D/4Screen(
WD)/7Screen(WD)/8Screen/9Screen-A/9Screen-
B/9Screen(WD)/12Screen(WD)-A/12Screen(WD)-
B/16Screen
    Refer to page 84 for further information about each set-
ting value. 
SEQ: Displays images from camera channels sequen-
tially according to the settings performed in advance.
Note:
	 •	 When	the	selected	multi-screen	setting	is	unavailable	for	 the web browser, live images from Camera 1 will be dis-
played after the login from the web browser.
[Camera	partitioning]
Determine the operational functions of each camera channel. 
It is impossible to change the setting value for an administra-
tor. "0" has been set for the administrator. 
[Edit]	button
Modifies the administration information.
    
■  PS.Data
[PSD	user]
Configure the settings for a user when using a PS·Data com-
patible controller. A PSD user should be one of the regis-
tered users for the recorder. An auto login user should be 
one of the users registered in the recorder. 
     
						

							108
Register,	change	or	delete	the	user	information	[User]
Select the [User] tab on the "User mng." page. (+ Page 60)
The user information such as the user name, password and operation level can be registered, changed and deleted on this tab. 
Registers user information
Register user information such as a user name, password and operation level. 
Select the [Registration] button after completing each setting item. 
    
[User	name]
Enter a user name.Enter 5 to 14 alphanumeric characters for 
the user name.
[Password]
Enter a password.Enter 5 to 8 alphanumeric characters for 
the password.Important:
	 •	 For	enhanced	security,	change	the	password	on	a	regu- lar basis. 
 
[Level]
Display the operation level of a user. 
Operable functions can be set in the "User level" tab  
(+ page 112). 
    LV1/LV2/LV3
Default: LV1
[Access	priority]
Displays the settings to assign priorities to operate the 
recorder in case two or more users access the recorder 
simultaneously. 
    1 (high)-16 (low)
Default: 1
[Default	screen]
Select a startup display to be displayed after login from the 
following. Available setting values are the same as "Default 
screen" of the [Administrator] tab. 
Note:
	 •	 When	the	selected	multi-screen	setting	is	unavailable	for	 the web browser, live images from Camera 1 will be dis-
played after the login from the web browser.
     [Camera	partitioning]
Determine the operational functions of each camera channel. 
View/Operate: Displaying live images, displaying recorded images and controlling cameras are possi-
ble. 
View: Displaying live images and displaying recorded  images are possible, but controlling cameras is 
impossible. 
– –: Displaying live images, displaying recorded images  and controlling cameras are impossible. 
Default: View/Operate:
[Edit/Delete]	button
Select this button to display the "User edit" page.
Select this button to change or delete the user information 
that has been registered.
[Registration]	button
Select this button to newly register the edited user informa-
tion. 
     
						

							109
Change or delete the user information
Change or delete the user information that has been registered. 
    
Step 1
Select the [Edit/delete] button on the [User] tab.
  →  The "User edit" page will be displayed. 
Step 2
Select the "User name" of the user to change or delete the 
user information.
  →  The user information of the selected user will be dis-
played. 
Note:
	 •	 Select	the	[Back]	button	to	return	to	the	screen	to	regis- ter a user.
    Step 3
To change the user information, select the [Edit] button after 
changing the user information by performing the same pro-
cedure as user registration. (+ Page 108)
Select the [Delete] button to delete the selected user. 
     
						

							110
Register, change, or delete a PC (host) accessible to this recorder 
[Host]
Select the [Host] tab on the "User mng." page. (+ Page 60)
The information of host that accesses the recorder via a network can be registered, changed and deleted on this tab. 
Registers host information
Registers the host information such as the IP address, operation level and priority. 
Select the [Registration] button after completing each setting item. 
    
[Host	IP	address]
Enter an IP address. Enter 4 units from the decimal numbers 
(0-255). Enter 4 units from the decimal numbers (0-254). Note:
	 •	 When	performing	the	settings	using	the	web	browser,	it	 is possible to use "*" that stands for all numbers.
	 •	 It	is	impossible	to	register	"0.0.0.0"	and	"∗.∗.∗.∗".
[Level]
Display the operation level of a host. 
Operable functions can be set in the "User level" tab  
(+ page 112). 
    LV1/LV2/LV3
Default: LV1
[Access	priority]
Displays the settings to assign priorities to operate the 
recorder in case two or more hosts access the recorder 
simultaneously. 
    1 (high)-16 (low)
Default: 1
[Default	screen]
Select a startup display to be displayed after login from the 
following. Cam.1 to 16: Displays an image from the selected cam-era channel on a single screen.
    4Screen-A/4Screen-B/4Screen-C/4Screen-
D/9Screen-A/9Screen-B/16Screen
Refer to page 84 for further information about each setting 
value. SEQ: Displays images from camera channels sequen-tially according to the settings performed in advance.
     [Camera	partitioning]
Determine the operational functions of each camera channel. 
View/Operate: Displaying live images, displaying recorded images and controlling cameras are possi-
ble. 
View: Displaying live images and displaying recorded  images are possible, but controlling cameras is 
impossible. 
– –: Displaying live images, displaying recorded images  and controlling cameras are impossible. 
Default: View/Operate
[Edit/delete]	button
Select this button to display the "Host edit" page.
Select this button to change or delete the host information 
that has been registered.
[Registration]	button
Registers the host information.