Panasonic Digital Disk Recorder Wj Hd616 Wj Hd716 Installation Guide

							81
Step 1
Select the desired day of the week.
  →  The time table of the selected day of the week will be 
displayed. 
Step 2
Configure each setting item. 
There are 2 setup pages. To move to another page, select 
the [k] or [l] button. 
    
[Copy	the	other	program]
To copy a time table set for another day of the week, select 
the day of the week to be copied, and select the [Copy] but-
ton.
■  New time table setup
Configure the settings of the following item for each time 
zone. 
[Start]
Set the start time of the time zone. 
[End]
Set the end time of the time zone. 
Note:
	 •	 The	time	can	be	set	in	1-minute	increments.
    However, the end time should be at least 15 minutes 
later than the start time.
	 •	 It	is	impossible	to	set	"23:46"	or	later	for	the	start	time.
	 •	 Set	"Start"	and	"End"	in	the	24-hour	time	display	format.
[Program]
Select the desired program (PROG1 to 4). 
[Event]
Select "On" or "Off" to determine whether or not to perform 
event actions at an event occurrence. 
[Alarm	message]
Select "On" or "Off" to determine whether or not to display 
the pop-up window that notify of an event occurrence with a 
message on the screen of the PC. 
[FTP	image	transmission	by	alarm]
Select "On" or "Off" to determine whether or not to transmit 
the alarm image to the FTP server according to the settings 
of "Image transmission by alarm" (+ page 96) on the 
"Server" page - the [FTP] tab. 
    
Assign	a	program	after	setting	the	time	zone	[Time	table]
Select the [Time table] tab on the "Schedule" page. (+ Page 60)
A time table for program actions can be created for each day of the week, and programs can be assigned to each time table. Up 
to 6 time tables can be created for each day of the week. 
When a signal is supplied from the ALARM/CONTROL connector (external recording changeover, pin no. 24), the recorder will 
work with the set timetable for "Ext." regardless of the days of the week.
At the default, 0:00 to 24:00, PROG1 has been set for "Daily".
     
						

							82
[Panasonic	alarm	protocol]
Select "On" or "Off" to determine whether or not to automati-
cally notify the PC of the event information by Panasonic 
alarm protocol at an event occurrence. 
[Mail]
Select "On" or "Off" to determine whether or not to transmit 
the alarm mail according to the settings of the "Server" page 
- the [Mail] tab (+ page 97) at an event occurrence. 
    [Back]	button
Closes the time table of the selected day of the week and 
returns to the [Time table] tab. 
    
Set the following items for desired special days 
[Date]
Enter the desired date to be set as a special day. 
[Mode]
Select the day of the week to which the desired schedule is 
assigned. 
Note:
	 •	 Only	the	days	of	the	week	to	which	programs	have	been	 assigned on the [Time table] tab will be displayed.
    It is impossible to select this item when there are no 
available days of the week.
Configure the settings of recording programs for special days [Special 
days]
Select the [Special days] tab on the "Schedule" page. (+ Page 60)
It is possible to assign timetables to special days aside from other days of the week. Time tables for special days can be set for 
up to 30 days. 
The settings are configured by specifying dates as special days and by applying a schedule to the\
 specified special days. 
     
						

							83
Configure	the	settings	relating	to	display	[Display]
The settings relating to the display on Monitor 1 and Monitor 2 connected to the recorder and the display on a PC monitor con-
nected to the recorder via a network can be configured on the "Display" page. 
The settings relating to display switching patterns such as multi screen display and sequential display of live images can also be 
configured on this page. 
The "Display" page has [Common], [Monitor 1], [Monitor 2], [Camera title\
], [Network] and [Cascade] tabs. 
Common	settings	for	monitors	[Common]
Select the [Common] tab on the "Display" page. (+ Page 60)
The common display settings for Monitor 1 and Monitor 2 such as the sett\
ings of camera titles or the settings of the time display 
position can be configured on this tab. The settings relating to the multi screen display can also be configured on this tab. 
    
[Time	&	date	display	position]
Select the position to display the time & date. 
When setting the time & date to be recorded together with 
images, the time display will be recorded in the selected 
position. Refer to "Embedded Rec (Time & date)" (+ page 
68) of the "Basic" page - the "Recording" tab for how to 
record the time & date together with the images. L-Upper: Displays the time & date on the upper left cor- ner on the screen. 
R-Upper: Displays the time & date on the upper right  corner on the screen. 
L-Lower: Displays the time & date on the lower left cor- ner on the screen. 
R-Lower: Displays the time & date on the lower right  corner on the screen. 
Default: L-Upper
Note:
	 •	 Determine	whether	or	not	to	display	the	time	&	date	on	 Monitor 1 on the [Monitor 1] tab. (+  Page 86)
[Camera	title	display	position]
Select the position to display the camera title. 
When the settings are configured to record images together 
with a camera title, the camera title position will be deter-
mined on this setting. Refer to "Embedded Rec (Title)" (+ 
page 67) of the "Basic" page - the "Recording" tab for how 
to record the camera title together with the images. 
    L-Upper: Displays the camera title on the upper left cor- ner on the screen. 
R-Upper: Displays the camera title on the upper right  corner on the screen. 
L-Lower: Displays the camera title on the lower left cor- ner on the screen. 
R-Lower: Displays the camera title on the lower right  corner on the screen. 
Default: R-Upper:
Note:
	 •	 Determine	whether	or	not	to	display	the	camera	title	on	 Monitor 1 on the [Monitor 1] or [Monitor 2] tab.  
(+ Pages 86 and 88)
[Line	color	on	the	multi	screen]
Select a parting line color from the following.  White: Displays white parting lines. 
Gray: Displays grey parting lines. 
Black: Displays black parting lines. 
Default: White
[Multi	screen	setup]
Configures the multi screen display pattern and assigns 
camera channels to each multi screen segment. 
Select the [Setup] button to configure the settings.  
(+ Page 84)
     
						

							84
Configure the multi screen display pattern and assign camera channels to each 
multi screen segment
Select the display pattern when switching to the multi screen display. In addition, assign the camera channels to each multi 
screen segment. 
When selecting the [Setup] button of "Multi screen setup" on the [Common] tab, the setup page for camera channel alloca\
tion 
will be displayed.
    
To configure the settings, do the following. 
    
Step 1
Check the desired multi screen display pattern of the param-
eters of "Use". 
The desired display pattern can be selected while moving to 
the previous or next page by selecting "Prev page or Next 
page". To return to the [Common] tab, select the [Back] but-
ton.  4Screen-A: Displays images from camera channels 1 - 4 on a 4-split screen. 
4Screen-B: Displays images from camera channels 5 -  8 on a 4-split screen. 
4Screen-C: Displays images from camera channels 9 -  12 on a 4-split screen. 
4Screen-D: Displays images from camera channels 13  - 16 on a 4-split screen. 
4Screen (WD): Displays images from camera channels  on a 4-split screen. Images from any camera chan-
nels can be selected. 
     7Screen	(WD): Displays images from camera channels 
on a 7-split screen. Images from any camera chan-
nels can be selected. 
8Screen: Displays images from camera channels on a  8-split screen. Images from any camera channels 
can be selected. 
9Screen-A: Displays images from camera channels 1 -  9 on a 9-split screen. 
9Screen-B: Displays images from camera channels 10 -  16 on a 9-split screen. 
9Screen (WD): Displays images from camera channels  on a 9-split screen. Images from any camera chan-
nels can be selected. 
12Screen (WD)-A: Displays images from camera chan- nels 1 - 12 on a 12-split screen. 
12Screen (WD)-B: Displays images from camera chan- nels 13 - 16 on a 12-split screen. 
16Screen: Displays images from camera channels 1 -  16 on a 16-split screen. 
     
						

							85
Step 2
Select the desired camera channels to display on the multi 
screen. 
Select the [Setup] button of "Camera setup". 
  →  The setup page for camera channel allocation will be 
displayed. 
Note:
	 •	 The	[Setup]	button	is	displayed	on	"Camera	setup"	for	 multi screen display patterns for which any camera 
channels can be selected. The [Setup] button is not dis-
played for multi screen display patterns for which any 
camera channels cannot be selected. 
 
    Step 3
Select the desired camera channels to display on each seg-
ment on the multi screen. 
To return to the [Common] tab, select the [Back] button. 
Note:
	 •	 It	is	impossible	to	select	the	same	channel	to	display	 images from it on multiple segments on the multi screen.
	 •	 When	configuring	from	a	PC	(web	browser),	images	from	 cameras will not be displayed.
 
     
						

							86
Configure	the	display	settings	for	Monitor	1	[Monitor	1]
Select the [Monitor 1] tab on the "Display" page. (+ Page 60)
Select "On" or "Off" to determine whether or not to display the time, camera title and ala\
rm display on Monitor 1. 
The settings relating to the sequence display on Monitor 1 can also be configured on this tab. 
    
[Time	&	date	display]
Select "On" or "Off" to determine whether to enable or dis-
able the time display. 
[Camera	title	display]
Select "On" or "Off" to determine whether to enable or dis-
able the camera title display. 
[Alarm	display]
Select "On" or "Off" to determine whether to enable or dis-
able the alarm display. 
[Login	screen]
Select a camera image to be displayed during the login pro-
cedure. --: No camera image will be displayed. (Black screen)
Cam. 1 to Cam. 16: Displays an image from the select-ed camera channel on a single screen. 
    4Screen-A/4Screen-B/4Screen-C/4Screen-D/ 
4Screen(WD)/7Screen(WD)/8Screen/9Screen-A/ 
9Screen-B/9Screen(WD)/12Screen(WD)-A/ 
12Screen(WD)-B/16Screen/SEQ
    Refer to page 84 for further information about each multi 
screen display pattern, and refer to page 87 for further 
information about the sequential display.
Default: --
[Secret	view]
The secret view is a function that skips camera images dis-
played with a single screen display on Monitor 2 when dis-
playing with the sequential display on Monitor 1. Select "On" 
or "Off" to determine whether to enable or disable the secret 
view function.  On: Enables the secret view function. (Camera images displayed with a single screen display on Monitor 2 
is displayed as a black screen. ) However, when 
recorded images are displayed on Monitor 2, the 
black screen is not displayed. 
Off: Disables the secret view function. 
    
[Live	sequence]
Configure the sequential display settings of camera images. 
Select the [Setup] button to configure the settings.  
(+ Page 87)
[Sequence	timing]
Determine how to switch camera images.  Int: Switches images according to the settings of the "Dwell time" of "Live Sequence". 
Ext: Switches images by signals from an external  device. 
Mon2: Switches images according to the sequence tim- ing of Monitor 2. 
Note:
	 •	 "Ext"	is	selected	when	an	external	device	is	connected	 to output the sequence signals
	 •	 Pin	No.	21	(Sequence	Switching)	of	the	ALARM/ CONTROL connector on the rear panel of the recorder 
works as an input terminal when "Int" is set for 
"Sequence timing", and works as an output terminal 
when "Ext" is set. (+ Page 44)
 
     
						

							87
Configuring the sequence display settings
Configure the sequential display settings of camera images. 
When selecting the [Setup] button of "Live sequence" on the [Monitor 1] \
tab, the setup page for live sequence will be displayed. 
(+ Page 86)
    
Configure the following setting items for each step of 
sequential display. 
Up to 16 steps can be registered. 
[Cam.]
Select a camera image to be displayed at each step from 
the following. Cam. 1 to Cam. 16: Displays an image from the select-ed camera channel on a single screen. 
    4Screen-A/4Screen-B/4Screen-C/4Screen-D/ 
4Screen(WD)/7Screen(WD)/8Screen/9Screen-A/ 
9Screen-B/9Screen(WD)/12Screen(WD)-A/ 
12Screen(WD)-B/16Screen
    Refer to page 84 for further information about each set-
ting value. 
[Preset	position]
Select a camera preset position (---, 1 to 256). When "---" is 
selected, the camera does not move to any preset position. 
[Dwell	time]
Select an interval time to go to the next sequential step. 
    2s/3s/5s/10s/20s
[Back]	button
Closes the setup page for live sequence and returns to the 
[Monitor 1] tab. 
     
						

							88
Configure	the	display	settings	for	Monitor	2	[Monitor	2]
Select the [Monitor 2] tab on the "Display" page. (+ Page 60)
Set the position to display the status bar and select "On" or "Off" to determine whether or not to display the camera title. 
The settings relating to the sequence display on Monitor 2 can also be configured on this tab. 
    
[Status	display]
Select the position to display the status bar. Upper: Displays the status bar on the top of the screen. 
Low: Displays the status bar on the bottom of the screen. 
Default: Low:
[Camera	title	display]
Select "On" or "Off" to determine whether to enable or dis-
able the camera title display. 
[Login	screen]
Select a camera image to be displayed during the login pro-
cedure. 
Available setting values are the same as Monitor 1. Refer to 
page 86. 
[Live	sequence]
Configure the sequential display settings of camera images. 
The setup procedure is the same as Monitor 1. Refer to 
page 86. 
    
[Sequence	timing]
Determine how to switch camera images.  Int: Switches images according to the settings of the "Dwell time" of "Live sequence". 
Ext: Switches images by signals from an external  device. 
Note:
	 •	 "Ext"	is	selected	when	an	external	device	is	connected	 to output the sequence signals
	 •	 Pin	No.	21	(Sequence	Switching)	of	the	ALARM/ CONTROL connector on the rear panel of the recorder 
works as an input terminal when "Int" is set for 
"Sequence timing", and works as an output terminal 
when "Ext" is set. 
 
    
Configuring the sequence display settings
Configure the sequential display settings of camera images. 
When selecting the [Setup] button of "Live Sequence" on the [Monitor 2] \
tab, the setup page for live sequence will be displayed. 
The setup procedure is the same as Monitor 1. Refer to page 87. 
     
						

							89
Configure	the	camera	title	[Camera	title]
Select the [Camera title] tab on the "Display" page. (+ Page 60)
The camera title can be configured on this tab. 
    
[Display]
Enter a camera title to be displayed on Monitor 2. 
Enter up to 14 alphanumeric characters for the camera title. Note:
	 •	 Available	characters:
    !"#$%&'( )*+,-./:;?@[\]^_`{|}~ (space)
[Embedded	Rec]
Enter the camera title to be recorded together with the imag-
es.
The setting is also applied to the camera title to be displayed 
on Monitor 1. 
Enter up to 14 alphanumeric characters for the camera title.  Important:
	 •	 To	record	the	camera	title	together	with	the	images,	it	is	 necessary to select "On" for "Embedded Rec (Title)"  
(+ page 68) of the "Basic" page - the "Recording" tab. 
  Note:
	 •	 Available	characters:
    "#&( )*+,-./:;? (space)
     
						

							90
Configure the settings relating to the sequential display on a PC monitor 
[Network]
Select the [Network] tab on the "Display" page. (+ Page 60)
The settings for the sequential display when displaying images on a moni\
tor of a PC connected to this recorder via a network can 
be configured on this tab. 
    
[The	method	of	sequence]
Select the desired sequential display pattern from the follow-
ing. 1-screen: Displays images with the sequential display on a 1-split screen. 
4-screen: Displays images with the sequential display  on a 4-split screen. 
Default: 1-screen
[1-screen	live	sequence]
Configure the settings for the sequential display when dis-
playing images with the sequential display on a 1-split 
screen. 
When the [Setup] button is selected, the following setup 
page will be displayed to configure each setting item. 
     	 •	 [Cam.]
   
Select a camera image (---, Cam.1 - Cam.16) to be dis-
played at each step. When "---" is selected, the step will 
be skipped.
	 •	 [Preset	position]
    Select a camera preset position (---, 1 to 256). When 
"---" is selected, the camera does not move to any pre-
set position. 
	 •	 [Dwell	time]
    Select an interval time to go to the next sequential step. 
    2s/3s/5s/10s/20s
	 •	 [Back]	button
    Closes the setup page for 1-screen live sequence and 
returns to the [Network] tab.