Panasonic Digital Imaging System Dp 1810f Copier Operating Instructions
Have a look at the manual Panasonic Digital Imaging System Dp 1810f Copier Operating Instructions online for free. It’s possible to download the document as PDF or print. UserManuals.tech offer 10737 Panasonic manuals and user’s guides for free. Share the user manual or guide on Facebook, Twitter or Google+.
21 NOTE Creative Features Job Memory Making Copies Two Copy Jobs Can Be Programmed in Memory (M1, M2) for recall at a later time. To Store a Job in Memory #Set up the copy job to be stored in memory, by first selecting each function you wish the copier to perform. $Press the MEMORY IN (F2) key. %Press the M1 (F3) or M2 (F4) key. To Recall a Job Stored in Memory &Place the Original (Press the M1 (F3) or M2 (F4) key. The stored contents will be displayed. )Press START CStored job(s) will not be deleted even if the power switch is turned Off. CWhen storing a new job into programmed memory, the previously stored job will be overwritten. JOB MEMORY PRESS M1,M2 TO STORE. RECALL JOB MEMORY LOADING...
22 Creative Features Sort Copy 1 1 1 1 11 NOTECWhen the memory becomes full during original scanning, the message “OUT OF MEMORY ” “CONTINUE 1:YES 2:NO” will be displayed in the message display. If this occurs, follow the instructions in the message display. For additional memory consult your authorized servicing dealer. CTo reset all job settings, press the RESET key. Sort Copy The sort copy has 2 available electronic sorting functions as follows: Note: Before using the sort copy, select the desired sorting mode by setting its function first (See page 28). 1 ADF : Place the Originals Platen: Place the First Original 2 Select the SORT Mode (3) COPY SIZE (Reduction/ Enlargement Only) 4 Number of Copies 5 Press START 6 ANOTHER ORIGINAL? 1:YES 2:NO Press “1” key. 7 Place next Original 8 Press START 9 Repeat steps 6 and 7 until all originals are scanned and stored into the copier’s memory. 10 ANOTHER ORIGINAL? 1:YES 2:NO Press “2” key. Sort Sort-Rotate Multiple copies sorted automatically.Multiple copies sorted automatically and Stacked in alternate direction. (Up to Letter size) From Platen Glass only:Platen Glass ADF
23 NOTE INTERRUPT (F1) Key ENERGY-SAVER Key These modes can save power while the copier is not in use. Energy Saver Mode #To enter this mode Press the ENERGY-SAVER key or the copier will automatically enter the Energy Saver Mode after 15 minutes * from the last copy. The indicator will flash. $To cancel this mode and make copies Press the ENERGY-SAVER key again. Sleep Mode #Automatically enters the Sleep Mode after 30 minutes from the last copy. The copier power will drop and the indicator will light. $To make copies, press the ENERGY-SAVER key. Interrupt Mode CThis mode can interrupt other copy jobs while making copies. #Press the INTERRUPT (F1) key, the indicator will light. $Make another copy job using the platen glass. %Press the INTERRUPT (F1) key again to continue the original job. Note: The ADF can not be used with interrupt. (Use only the Platen) ∗Energy saver time (15 minutes) and Sleep time (30 minutes) can be changed by the key operator. (See page 30) Other Features Modes Power Consumption Warm Up Time Normal Operation Energy Saver Mode Sleep ModeApproximately 92 Wh Approximately 40 Wh Approximately 1.5 WhN/A 30 sec. recovery 30 sec. recovery ENERGY SAVER INTERRUPT Making Copies Energy Saver/Interrupt Mode
24 CAn incorrect exposure may occur when there is a black line at the edge of the original or an image which the copier interprets as a black pattern in the Skyshot mode. CAn incorrect position detection of the original may occur when a strong light shines onto the glass during Skyshot mode. Other Features Skyshot Mode Skyshot allows copying a manuscript without generating dark borders even if the platen cover or ADF is opened. Skyshot mode eliminates dark borders around the originals, and is especially convenient for copying small-sized originals like bank checks or documents with unusual shapes (round, oval, etc.). These documents can be reproduced without generating any unnecessary black areas simply by making a copy with the cover open. Two types of Skyshot modes can be selected; Digital Skyshot Mode : The scanning area (size) is not pre-determined. Manual Skyshot Mode : The scanning area (size) is pre-registered into memory (M1 and M2) in advance. (See page 29) Digital Skyshot Mode 1 Place the Original on the platen (Opening the Platen Cover/ADF) Note: The default setting of Digital Skyshot Mode is “NORMAL”. In this setting, the unit scans once. If there are black areas around the borders in the copies, set the Digital Skyshot Mode to “QUALITY” to soften the dark borders. In this setting, the unit scans twice. #Press the FUNCTION key. $Press the 2 key to select COPIER SETTINGS. %Press the SET key. &Press 6 and SET key to select DIGITAL SKYSHOT. ( Press 1-3 key to select the Digital Skyshot Mode. 1: OFF NONE 2: NORMAL Default setting (usually select this mode). 3: QUALITY For better definition, select the Quality mode. )Press the SET key. *Press the RESET key. FUNCTION MODE (1-2) ENTER NO. OR ∨ ∧ 2:COPIER SETTINGS PRESS SET TO SELECT COPIER PARAM. (00-14) ENTER NO. OR ∨ ∧ 06 DIGITAL SKYSHOT 2:NORMAL 3 Press START Key 2 Number of Copies NOTE
25 NOTE 1 Place the Original 23 Number of Copies 4 Press START Select the Custom Size (M1 or M2) Upper- left corner Platen Manual Skyshot Mode When using this function, the custom size should be registered into memory (M1, M2) in advance. (See page 29) Other Features 2 ∗The default size for M1 is: 70(X) × 160(Y) mm, and M2 is: 95(X) × 220(Y) mm CWhen changing the M1 or M2 size, consult with the key operator. CWhen using the Manual Skyshot mode, M1 and M2 are turned ON and other job memory cannot be used. CPress the RESET key to cancel all job settings. FUNCTION MODE (1-2) ENTER NO. OR ∨ ∧ 2:COPIER SETTINGS PRESS SET TO SELECT COPIER PARAM. (00-14) ENTER NO. OR ∨ ∧ 07 MANUAL SKYSHOT 2:M1 ON #Press the FUNCTION key. $Press the 2 key to select COPIER SETTINGS. %Press the SET key. &Press 7 and SET key to select MANUAL SKYSHOT. (Press 2 or 3 key to select the Custom Size. 1: OFF NONE 2: M1 ON M1 size is ON* 3: M2 ON M2 size is ON* 4: M1, M2 ON Both sizes are ON )Press the SET key. *Press the RESET key. Making Copies
26 Next Selections2-ORIGINAL H COPYMargin SORTOther Functions Zoom Copy 2 in 1 Copy 2 Page CopySort-Rotate Manual Skyshot Job Memory Retrieval Job Memory Storing Remarks First Selections Sort Book Edge Margin Non-Sort Combined Function Table OAAOOOOOOAAO OAAOOOOOOAAO OO OAOOOOOAAO OO OOAOOOOAAO OO OOOAOOOAAO O O O OOOAAA A AO O O O OOOAAA A AO OO OOOOAAA A AO O✕✕OOO–––AA✕ O✕O OOO–––✕✕✕ Zoom Copy 2-ORIGINAL H COPY Margin Other Functions SORT 2 in 1 Copy 2 Page Copy Book Edge Margin Non-Sort Sort Sort-Rotate Manual Skyshot Interrupt O: Possible Combined Functions. ✕: Unavailable Combined Functions. A : Next Selection is Carried Out. –: Indicates that SORT mode cannot be used. Non-sort operation is carried out.AO O OOOOOOAAO
27 NOTE Procedure RESET Key #Press the FUNCTION Key $Press 1 (GENERAL FUNCTIONS) or 2 (COPIER SETTINGS) key. You may also use the (G or F) keys. %Press the SET key. &Press the Keypad to select function modes or use the (G or F) keys. (Follow the on screen instructions. )After setting, press the SET key to set up the function. CPlease refer to each option’s operating instructions for function settings. Printer Settings for Key OperatorGeneral Functions for Key OperatorCopier Settings for Key OperatorLAN Settings for Key Operator Input Identification Code Printer Settings Using Function Modes to Change the Initial Copy Modes General FunctionsCopier SettingsLAN Settings Options Function Making Copies Checking the Copier’s Total Counter To display the copier’s Total Counter, press the COPY SIZE and PAPER TRAY keys simultaneously.COPY SIZE KeyPAPER TRAY Key FUNCTION MODE (1-2) ENTER NO. OR ∨ ∧ FUNCTION Key
28 Function No. ModesInitial Setting Function 00 SORT MODE DEFAULT Selects the sort mode. CNON-SORT, SORTNON-SORT General Functions 05 Displays the amount of sort memory used on the panel. COFF, DISPLAYSORT MEMORY USAGEOFF Copy usage and copy limit of the selected department and total copy usage will appear on the screen. DEPT. COUNTERConsult your service technician. 06 08 09Select Sort-Rotate mode. COFF, ON SORT-ROTATE DEFAULT OFF KEY OPERATOR MODEInput the key operator ID code. 02 POWER ON DEFAULT Select mode.* CCopy, FaxCopy ∗Not available for plain copier, but will be available when installing options with advanced functions. (See page 51)NOTE
29 No.ModesInitial Setting Function 00 MARGIN DEFAULT Selects the margin position and shift value. CPOSITION (Left, Right, Top, Bottom) CVALUE (5 - 99 mm)LEFT 10 mm Copier SettingsFunction Selects the edge mode (Equal Rate = set the same value for X & Y or Individual = set the value for X & Y individually) and width. CEQUAL RATE (X & Y ), INDIVIDUAL C5 - 99 mm EDGE DEFAULT 05 Selects whether or not to disable edge deletion. CINVALID, VALID 2 in 1 WITH FRAMESelects the book Center Void margin width. C5- 99 mm BOOK MARGIN DEF.EQUAL RATE 5 mm 20 mm INVALID Enables or disables the use of skyshot mode. COFF, NORMAL, QUALITY DIGITAL SKYSHOT NORMAL OFF VALID Enables or disables the use of Manual Skyshot. COFF; M1 ON; M2 ON; M1, M2 ON MANUAL SKYSHOT Input key operator ID code. KEY OPERATOR MODEAutomatically adjusts the copy density for text and photographic originals. CINVALID, VALID AUTO EXPOSURE 01 02 06 07 08 14 PORTRAIT L \ R Selects the orientation and layout for 2 in 1 Copy. CORIENTATION (Portrait, L-Scape) CLAYOUT (L \ R, R \ L) 2 in 1 DEFAULT 12 L \ R Selects the 2 page mode. CL \ R, R \ L 2 PAGE MODE DEF. 13 INVALID Select the reduction ratio in margin mode. CINVALID, VALID FRAME MARGIN 03 NOTECCertain Functions or Parameters are available for selection only when their respective option is installed. Making Copies
30 Function General Functions for Key Operator No.ModesInitial Setting Function NOTE Selects the Control Panel reset time. COFF, 30 sec, 1 min., 2 min., 3 min., 4 min. Selects the message language of the display. CA-ENGLISH, C-FRENCH, SPANISH AUTO RESET TIME LANGUAGE DEFAULT 05 Sets the paper tray for special paper (ex: colored). CNONE, TRAY 1, TRAY 2, BYPASS SPECIAL TRAY 1NONE Sets the Energy Saver mode and time. CINVALID, ENERGY-SAVER, SLEEP Energy save mode timer : 1-120 minutes Sleep mode timer : 1-120 minutes ENERGY SAVER MODE 1 min. SLEEP A-ENGLISH KEY/TOUCH BEEPSets the panel touch sound. COFF, SOFT, LOUDSOFT 01 02 04 09 Sets the date & time. DATE & TIME Sets daylight saving time. CINVALID, VALID DAYLIGHT TIME 20 21 CIt is necessary to input the Key Operator ID code before changing items on this page. CThe Special Tray 1 and 2 are not auto-selectable in the switching mode. ∗Not available for plain copier, but will be available when installing options with advanced functions. (See page 51) Sets the paper tray for special paper. CNONE, TRAY 1, TRAY 2, BYPASS SPECIAL TRAY 2 NONE 06 Sets the sound when put paper(s) on bypass tray. C1: INVALID 2: VALID BYPASS SET BEEP INVALID 10 Sets the sound when put paper(s) on ADF. C1: INVALID 2: VALID ORIG. SET BEEP ADF VALID 11 Prints list containing Current Setting and Standard Setting. COPY SETTING LIST 25VALID Sets the paper size of each paper tray. CTray-1, Tray-2, Tray-3, Tray-4 PAPER SIZEConsult your service technician. 00 Sets the on time and off time for Energy Saver mode. CStart time - End time ENERGY SAVER TIME 03 Total print out volume from the PC. PC PRINT COUNT 16 Total print out volume from the main unit. TOTAL COUNT 15