Panasonic Digital Imaging System Dp 1810f Copier Operating Instructions

							41
NOTECMake sure that the misfeed indicator goes off after removing the misfed
paper.
CThe misfeed indicator will not go off if the paper is still jammed in the copier.
Check again and remove all misfed paper.
Paper Misfeed Locations
A: ADF (see page 45)
(J70, J71)
B: Copier (Paper Exit, Paper Entry/Transport)
area (see page 42-43)
(J51 - J59, J80)
C: Paper Feed Module (see page 44)
(J00 - J50)
IMisfeed Indicator
Removing a Misfed PaperProblem Solving

 

 


Paper Misfeed Indicators and Locations
When a paper misfeed occurs, the misfeed indicator and the misfeed
location(s) will be displayed on the panel display.
I 
						

							42
ATTENTION
Removing a Misfed Paper
CMake sure that the misfeed indicator goes off after removing all misfed paper.
1
Remove the misfed paper. 
Paper Exit Area
CMake sure that the misfeed indicator
goes off after removing all misfed
paper.
Problem Solving 
						

							43
Problem Solving
1
2
3
Open the Right Cover.
Remove the misfed paper.
If copy paper is fed far into the copier:
#Turn the right paper clearing knob.
$Remove the misfed paper.

Paper Entry/Transport Area
CMake sure that the misfeed indicator
goes off after removing all misfed
paper.
ATTENTION
4
#Open the Heat Roller Cover.
$Remove the misfed paper.
%Close the Right Cover.
Caution: This fuser area may be
hot.Caution
heated
surface
CMake sure that the misfeed indicator goes off after removing all misfed paper.
I 
						

							44
Problem Solving
1
2
#Pull the Paper Tray out.
$Remove the misfed paper.
%Return the Paper Tray to the original
position.
#Open the Feed Cover.
$Remove the misfed paper.
%Close the Feed Cover.

Paper Feed Module
CMake sure that the misfeed indicator
goes off after removing all misfed
paper.
CMake sure that the misfeed indicator goes off after removing all misfed paper.ATTENTION
Removing a Misfed Paper 
						

							45
Problem Solving
ATTENTION
1
2
#Open the Entry Cover.
$Remove the misfed paper.
%Close the Entry Cover.
#Open the ADF Cover.
Note: To prevent damaging the originals,
open the ADF Cover before
removing the misfed original(s).
$Remove the misfed paper.
%Close the ADF Cover.
&Close the ADF.

ADF
CMake sure that the misfeed indicator
goes off after removing all misfed
paper.
CMake sure that the misfeed indicator goes off after removing all misfed
paper.
CTo prevent original(s) damage, please make sure to open the ADF Cover
before removing misfed original(s).
I 
						

							46
Troubleshooting
Before Calling Service
CheckAction
Unit Does Not Operate
Does the display light?Check if the Power Switch is turned On and
that the power cord is connected into the
outlet.
Does the Energy Saver key flash (or light)
and displays are turned OFF? (See page
23)Press Energy Saver key on the Control
Panel.
Perform actions in accordance with each
message. Does any of the U## codes and messages
appear on the display?
(U01, U07, U13, U14, U20 and U21) (See
page 48)
Add paper. (See page 38) Does the add paper indicator and message
appear on the display? (J)
∗
Remove the misfed paper. (See page 41) Does the paper misfeed indicator and
message appear on the display? (I)
Turn the copier Off, then On. If the Error
Code does not clear, call for service. Does E#-## indicator and message appear
on the display?
(No) (Yes)
When the Add Toner Warning Indicator begins to flash
∗ or is lit, replace the toner bottle with a new
one.  After this warning is activated, machine operation will begin with the Toner Charging Mode
(approximately 3 minutes to complete) each time the power switch is turned Off then On or if the
Front/Right Cover is opened and then closed.
Note: 
∗When the warning indicator starts flashing, a 300-sheet count-down counter is activated,
and upon reaching 0 the machine will stop operating.  The 300-sheet counter is based on
6% fill, depending on the density some pages may print Blank.
Machine operation and displays are as follows:
1. When turning the power switch to On or opening and then closing the Front/Right Cover, the
machine starts to warm-up and the LCD displays:
PLEASE WAIT...
(No)
(No) (No)
(No)(Yes)
(Yes)
(Yes)
(Yes)
(Yes) 
						

							47
Troubleshooting
Check Action
Light Copies
Does the exposure indicator say “Lighter”?Press the Darker key until the indicator
LED is set to Darker. (See page 12)
Does the add toner indicator and message
appear on the display? (?)Add Toner. (See page 39)
Marked Copies
Is the copier platen glass or platen cover
dirty?Clean the Glass or Platen Cover.
(See page 48)
2. The Toner Charging Mode starts and the LCD displays:
Add Toner Warning  Indicator:
CFlashing = Toner Bottle is nearly empty
CLit = Toner Bottle is empty
3. This message is displayed for approximately 200 seconds.
∗Each “ ❚ ” is approximately 10 sec.
4. This massage will continue to be displayed until the warm-up cycle is completed, and if the toner
bottle was replaced. Upon completion, the Add Toner Warning Indicator automatically turns Off.
(No)(Yes)
CHARGING TONER
CHARGING TONER
❚ ❚ ❚ ❚ ❚
(Yes) (Yes)
Others 
						

							48

If the measures outlined above do not solve the problem, call your Service provider.
Platen
Cover
Platen
(glass)
Copier Care

 As a rule, clean weekly.
Platen/Platen Cover
#Wipe marks off with a cloth and a neutral
detergent.
$Wipe again with a dry cloth. Platen
Cover
Platen
(glass)
User Error Codes (U Code) Troubleshooting
The self-diagnostic functions detect troubles in the important components of the copier.
When any trouble occurs, the copier stops.
Code Display Message Check Points
U01 CLOSE FRONT/RT COVER Front Cover is open.
U07 CLOSE FEED COVER Feed Cover is open.
U13TONER IS RUNNING LOW
NO WASTE TONER BOX1. Toner Bottle is incorrectly installed.
2. Low Toner.
U14 WASTE TONER BOX IS FULL1. Toner Waste Container is incorrectly
installed.
2. Toner Waste Container is full of toner.
U20 CLOSE ADF COVER ADF Cover is open.
U21 CLOSE PLATEN COVERWhile the copier is initializing, the ADF
Cover was opened. (Optional ADF installed) 
						

							49
ATTENTION
Reinstall the Battery Holder.
Troubleshooting
Replacing the Battery
The copier has an internal battery (Product No.: CR2032) which maintains the date
setting in the event of a power outage.

 

 


Battery Replacement Required Message
1
Turn the power Off.
Pull out the Battery Holder.
2
Replace the Battery.
3
denotes hazards that could result in minor injury or damage to the machine.CThe service life of the battery is approximately 1 year when the machine is
turned “Off ”.
REPLACE BATTERY
                U90

 

 


Battery Replacement Procedure
Turn the power On.
Set the Date and Time. (See P.30)
4
Others
ATHIS PRODUCT CONTAINS A LITHIUM BATTERY. DANGER OF EXPLOSION IF BATTERY IS
INCORRECTLY REPLACED.
REPLACE ONLY WITH THE SAME OR EQUIVALENT TYPE. DISPOSE OF USED BATTERIES
ACCORDING TO THE  INSTRUCTIONS  OF YOUR  LOCAL  SOLID WASTE  OFFICIALS.
CAUTION 
						

							50
Specifications

 

 


DP-1810F (Copier)
Platen TypeFixed
Acceptable OriginalsSheets, Books (max. Ledger)
Copying MethodLaser Electrophotography
Fixing MethodHeat Roller Fixing
Resolution
Max. 600 dpi
Maximum Copy SizeLedger - Invoice via paper tray
Void AreaMax. 0.2 in (5 mm)
Warm Up TimeApprox. 30 seconds (68°F/20°C)
First Copy TimeApprox. 6.5 seconds (Letter , from 1st tray)
Multi-Copy Speed18 Letter size copies per minute
Enlargement RatiosPreset: 121%, 129%, 155%, 200%
Variable: from 101% to 200% in 1% increments
Reduction RatiosPreset: 79%, 77%, 65%, 61%, 50%
Variable: from 99% to 50% in 1% increments
Paper FeedPaper tray (550 sheets × 1) + Sheet bypass (50 sheets)
2nd Paper feed module (550 sheets - option)
3rd Paper feed module (550 sheets - option)
4th Paper feed module (550 sheets - option)
Paper WeightPaper Tray: 16 - 24 lb (60 - 90 g/m
2)
[Sheet Bypass: 15 - 34 lb (56 - 128 g/m2)]
Quantity SelectorMax. 999 sheets (output tray capacity is 250 sheets)
Electrical ConsumptionAC 120V, 50/60Hz, 9A
Energy ConsumptionMax. 1.2 kW, 1.5 Wh in Sleep Mode
Imaging MethodDry-Type Single component imaging
Dimensions (W 
× ×× ×
× D 
× ×× ×
× H)23.1 × 25.5 × 20.6 in
(588 × 647 × 522 mm)
Weight99 lb (45 kg)
Operating EnvironmentTemperature: 50 - 95°F (10 - 35°C) Relative Humidity: 45 - 85%
(However, the humidity should be 70% or less at a temperature of 95°F (35°C),
and the temperature should be 86°F (30°C) or less at a humidity level of 85%.)
CSpecifications are subject to change without notice.
TypeDesktop